E30/E36 Lock Increase Guide - My try with photos

Need technical Q/A then you're in the right place

Moderator: martauto

Phill172
E30 Zone Camper
E30 Zone Camper
Posts: 1117
Joined: Wed Feb 20, 2008 11:00 pm
Location: Basingstoke

Post Thu Nov 03, 2011 9:39 am

Not sure if this is in the correct section. And also not sure if this has been covered before but I thought it may help others out!

Im still in the process of doing this so this will be updated

From doing as much reading as I can about increasing the lock on a E30/E36 there seemed to be alot of unsures as to how to do it.

Anyhow as you know I have an E30, my car set is.

E36 M3 Evo Hsd Coilovers + Adjustable top mounts (HSD)
E36 M3 Evo Lower Wishbones
E36 M3 Evo eccentric powerflex bushes
E36 325 Steering rack
E36 325 tie-rods
E36 M3 Evo hubs/discs/calipers
Rota Grid et0 8.5j (ish) inc 25mm spacers

This gave me lock like this
Image
Image

Which was great although alot of the time the back of the wheel would catch on either the Anti roll bar or the chassis, of which the latter was sorted by cutting the chassis rail and boxing it in. This would cause the wheel to lock/slow make my handling feel gay and alot of the time spin the car.

So I thought it was time to get some E46 wishbones and see what could be achieved. I managed to pick up some wishbones from a breakers that I used throughout the whole build of the V8 in my car, and next day they arrived.
(im going to cheekily rob some photos from another forum).
Anyway this is the differance.
Image

A noticable differance in length (not sure exactly how much) but also they weigh almost half the weight of the E36 varient.

Onto fitting the bush, after doing alot of reading people state that you have to grind the end of the E46 wishbone down as it is hexagonal and a E36 is circular. Not only that but you MUST also grind the shoulder of the E46 wishbone down too, otherwise the bush wont sit far enough down on the wishbone and you will never get it to line up for the mount pointing point on the chassis leg.

Image

Next is to offer the wishbone up and bolt it into place like this
Image

and bolt the hub to it

Image
Image

Once this is all together you will notice if you do attach the tierod you will have MASSIVE toe in, for the moment (as my car is still in progress) I have adjusted the tie rod to suit, weather or not there is enough safely enough thread on the tie rod I will have to check. I have been told by a few people that you can use the stock e36 rack and tie rods.
However I will more then likely use a mixture of E34/E36 tierod components.

The change in the track width is very noticeable with the E46 wishbone

Here is a E36 wishbone
Image


And E46 wishbone
Image

I will probably run my car with this set up for the moment (DWYB in a week) so once im back I will be taking the hubs off and machine/weld the tierod mount on the hub like this (off another forum :o)

Standard
Image

Modified (ignore the wishbone mounting point has been cut, believe he did that to run the car lower but not to affect the wishbone angle.)
Image

Without the tierod attached it enabled me to see exactly how much lock could be achieved. The difference was huge!
Image
Image
Image

With the correct mods to the tierods and knuckle I think ill easily be able to achieve the lock that some more (very expensive kits offer) and for me its only cost me my time and £30, I will of course be looking into the roll centres etc, but at the moment im going to see how the car performs purely on the new geo that the E46 arms produce. Trying to take on step at a time so I dont fuck my cars handling up to much!

I hope this helps anybody looking to do the same, and I wont to try and prove you dont have to spend hundreds of pounds doing so!

Will update very soon!
cypriot_boy_2k7
E30 Zone Squatter
E30 Zone Squatter
Posts: 1641
Joined: Mon Jan 29, 2007 11:00 pm

Post Thu Nov 03, 2011 7:35 pm

Very nice, looks :cool:
Darrenr
E30 Zone Regular
E30 Zone Regular
Posts: 276
Joined: Thu Jul 21, 2011 11:00 pm

Post Fri Nov 04, 2011 8:21 am

Thats the way to do it :) great thread
User avatar
randomspeedfreak
E30 Zone Regular
E30 Zone Regular
Posts: 992
Joined: Mon Mar 15, 2010 11:00 pm
Location: Bristol

Post Fri Nov 04, 2011 9:14 am

how can you get the grinding you did to be accurate?!

thats gunna have some funky handling if you ask me!
Phill172
E30 Zone Camper
E30 Zone Camper
Posts: 1117
Joined: Wed Feb 20, 2008 11:00 pm
Location: Basingstoke

Post Fri Nov 04, 2011 10:14 am

The grinding? On the wishbone? That just allows the bush to sit far enough on?

In what why should the handling be funky?
User avatar
randomspeedfreak
E30 Zone Regular
E30 Zone Regular
Posts: 992
Joined: Mon Mar 15, 2010 11:00 pm
Location: Bristol

Post Fri Nov 04, 2011 10:24 am

Phill172 wrote:The grinding? On the wishbone? That just allows the bush to sit far enough on?

In what why should the handling be funky?
that pin that was a hexagon is now a circle, so it could be off center so as the suspension compresses the wishbone moves changing the geometry?

do you know jamie kay by the way?!
Phill172
E30 Zone Camper
E30 Zone Camper
Posts: 1117
Joined: Wed Feb 20, 2008 11:00 pm
Location: Basingstoke

Post Fri Nov 04, 2011 12:20 pm

randomspeedfreak wrote:

that pin that was a hexagon is now a circle, so it could be off center so as the suspension compresses the wishbone moves changing the geometry?

do you know jamie kay by the way?!
......Nahhhhh...... :D

haha

Yea I know Jamie, take it your from round here and proberly know Rob Nicklin???

I drift with both and am watching nicklin put a 4.0 m60 into a S14!
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Fri Nov 04, 2011 12:25 pm

Is this aimed at 'track use' only?
Youth is wasted on the young.
Phill172
E30 Zone Camper
E30 Zone Camper
Posts: 1117
Joined: Wed Feb 20, 2008 11:00 pm
Location: Basingstoke

Post Fri Nov 04, 2011 12:51 pm

The set up? Yes and no, I dont know if the potential benefit is worth it for the road, the lock side of things defiently couldnt see a benefit for the road but the wider track maywell be benifical on a road car, I will see how it performs and let you know

(certainly easier to obtain to do a 5 stud conv)

Bushes I can use E46 varients so I wouldnt of had to grind the wishbone down, but im poor at the moment!!!

:)
User avatar
randomspeedfreak
E30 Zone Regular
E30 Zone Regular
Posts: 992
Joined: Mon Mar 15, 2010 11:00 pm
Location: Bristol

Post Fri Nov 18, 2011 12:11 pm

Phill172 wrote:
randomspeedfreak wrote:

that pin that was a hexagon is now a circle, so it could be off center so as the suspension compresses the wishbone moves changing the geometry?

do you know jamie kay by the way?!
......Nahhhhh...... :D

haha

Yea I know Jamie, take it your from round here and proberly know Rob Nicklin???

I drift with both and am watching nicklin put a 4.0 m60 into a S14!
yeah back home is that way im just down the road from jamie im one of his good mates. ive met rob once or twice i think, would like to see your car at some point my e30 will be back around in a few weeks!