Running out of ideas... :(
Moderator: martauto
-
325isparda
- E30 Zone Newbie

- Posts: 105
- Joined: Thu Jun 02, 2011 11:00 pm
- Location: Essex
Hello all,
I have a 325i 1989 i bought a couple of year ago, it had been standing for about 18 months then i got the head rebuilt as the camshaft had worn. At first it was running fine with only a little ruchness but i was told i needed a new afm. Anyway as time went on things were fine untill one morning after the car had been standing over night, i started it and it was really lumpy, it could barely rev over 2000 revs and when it did it sounded like it was mis firing majorly. I was a bit worried so had a look around and couldnt find any problems. I then decided i would see what happens when it warms up so i took it for a drive and when warm it ran fine, me thinking the problem hasd cured itself the next morning did the same thing and has done ever since. I now have to leave the car to run for around 5-10 minutes to warm up before i can pull away safely otherwise the car wont rev up and when it does it's lumpy and mis-fires. A list of things i have changed
Blue temp switch
AFM twice
Induction hose
TPS
ICV
Cleaned throttle body
Relays
Dizzy cap
Rotor Arm
Leads
Plugs
Fuel Filter
Fuel Pressure Regulator
Inlet Manifold Gasket
Checks all connecters
And more that may have crossed my mind, i then also had a friend check with diagnostics but no luck. I have done countless compression tests and gas checks to see what could be happening but no luch. At the moment all i am left with is the idea that maybe i have a sticky valve. I now can't think of anything else i can do.
Any Ideas?
I have a 325i 1989 i bought a couple of year ago, it had been standing for about 18 months then i got the head rebuilt as the camshaft had worn. At first it was running fine with only a little ruchness but i was told i needed a new afm. Anyway as time went on things were fine untill one morning after the car had been standing over night, i started it and it was really lumpy, it could barely rev over 2000 revs and when it did it sounded like it was mis firing majorly. I was a bit worried so had a look around and couldnt find any problems. I then decided i would see what happens when it warms up so i took it for a drive and when warm it ran fine, me thinking the problem hasd cured itself the next morning did the same thing and has done ever since. I now have to leave the car to run for around 5-10 minutes to warm up before i can pull away safely otherwise the car wont rev up and when it does it's lumpy and mis-fires. A list of things i have changed
Blue temp switch
AFM twice
Induction hose
TPS
ICV
Cleaned throttle body
Relays
Dizzy cap
Rotor Arm
Leads
Plugs
Fuel Filter
Fuel Pressure Regulator
Inlet Manifold Gasket
Checks all connecters
And more that may have crossed my mind, i then also had a friend check with diagnostics but no luck. I have done countless compression tests and gas checks to see what could be happening but no luch. At the moment all i am left with is the idea that maybe i have a sticky valve. I now can't think of anything else i can do.
Any Ideas?
-
325isparda
- E30 Zone Newbie

- Posts: 105
- Joined: Thu Jun 02, 2011 11:00 pm
- Location: Essex
O yes and i forgot, How many miles are people getting to a full tank cause im barely getting 100-140? 
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Measure the blue temp, sensor resistance, cold and hot, at the ECU plug (above the driver's right knee).
-
Rtaylor2208
- E30 Zone Addict

- Posts: 3004
- Joined: Mon Oct 11, 2010 11:00 pm
- Location: Ayr, Ayrshire, Scotland
Watching with interest as I have the same issues but I have not replaced anything yet other than spark plugs.
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
and if the blue temp sensor checks out of then try the plug below the inlet manifold.
if thats ok then start looking for vacuum leaks, your symptoms and thought process is similar to the issues i have had with vacuum leaks.
theres a pipe from the sump to the inlet that can leak.
if thats ok then start looking for vacuum leaks, your symptoms and thought process is similar to the issues i have had with vacuum leaks.
theres a pipe from the sump to the inlet that can leak.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Brianmoooore wrote:Measure the blue temp, sensor resistance, cold and hot, at the ECU plug (above the driver's right knee).
-
325isparda
- E30 Zone Newbie

- Posts: 105
- Joined: Thu Jun 02, 2011 11:00 pm
- Location: Essex
I had a mate of mine who is an auto electrician to double check everything with diagnostics and check all the points. From what he says there is nothing going wrong in the electrics. So i then got one of my customers to check everything out e.g. head gasket, compression and what not and one of my cylinders took a while to bring comression up, giving us the idea that we may have a sticky valve
could this be causing all my problems?
Vacuum leaks i will check for tonight, i know that the breather underneath the inlet manifold has not sealed at the bottom near the casing and i do believe it is pissing out oil from there. Im going to get one of these from bmw and relpace it.
Vacuum leaks i will check for tonight, i know that the breather underneath the inlet manifold has not sealed at the bottom near the casing and i do believe it is pissing out oil from there. Im going to get one of these from bmw and relpace it.
-
lamby
- E30 Zone Regular

- Posts: 251
- Joined: Wed Jan 27, 2010 11:00 pm
do that breather first as that causes all sorts of rough running,that is prob the cause,and if its pissing out oil that can cause sticky tb aswell so run it through a catch tank once its running ok.
-
CHR1S1990
- E30 Zone Camper

- Posts: 1121
- Joined: Fri Mar 14, 2008 11:00 pm
- Location: Blackpool
Ive had this problem before. Firstly i would do exactly as brian describes as this was the problem - not the blue temp sensor itself but the wiring for it in the round plug under the inlet manifold. Measure the resistance at the temp sensor when cold/symptoms occuring, and compare it to measurements at the ecu plug. Simply spraying some contact cleaner in the plug may even sort it if only the pins are filled with water/corroded.

-
325isparda
- E30 Zone Newbie

- Posts: 105
- Joined: Thu Jun 02, 2011 11:00 pm
- Location: Essex
Thankyou for all the help... will let you all know how it goes. I was going to do the breather onenight after work this week but unfortunately the darkness at 5 in the evening is not helping haha. Gonna try and get it sorted this weekend, also got a friend doing a leak test to see what valve and how bad its sticking.
Just want the car to run better now lol.
Just want the car to run better now lol.
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
just struggled with mine in the dark yesterday and found the inlet gaskets were totally gone, hard and cracking up.
mine in 100% better now, it surprising how much of an effect an air leak can have on these.
mine in 100% better now, it surprising how much of an effect an air leak can have on these.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
-
CHR1S1990
- E30 Zone Camper

- Posts: 1121
- Joined: Fri Mar 14, 2008 11:00 pm
- Location: Blackpool
why would it cause a sticky TB? as far as I can tell he's talking about the breather pipe that runs from the head from the block, not the one from the rocker to the TBlamby wrote:do that breather first as that causes all sorts of rough running,that is prob the cause,and if its pissing out oil that can cause sticky tb aswell so run it through a catch tank once its running ok.

-
CHR1S1990
- E30 Zone Camper

- Posts: 1121
- Joined: Fri Mar 14, 2008 11:00 pm
- Location: Blackpool
+1HairyScreech wrote:just struggled with mine in the dark yesterday and found the inlet gaskets were totally gone, hard and cracking up.
mine in 100% better now, it surprising how much of an effect an air leak can have on these.
Id sealant the ICV pipe and brake vacuum pipes into the TB too, theyre kinda just vaguely pushed in there!

-
lamby
- E30 Zone Regular

- Posts: 251
- Joined: Wed Jan 27, 2010 11:00 pm
it wont if it,s that one it will still cause rough running though
-
CHR1S1990
- E30 Zone Camper

- Posts: 1121
- Joined: Fri Mar 14, 2008 11:00 pm
- Location: Blackpool
true but mostly only at idle, and I cant see it stopping the engine rev over 2000rpm, nor would the problem dissapear when warm.
im still convinced you have an electrical problem, probably blue temp sensor wiring. I was reading this last night about motronic 1.3:
"Limited Operating Strategy (LOS)
In the event of a serious fault in one or more of the sensors or their wiring circuits, Motronic will substitute a fixed default value in
place of the defective sensor. This procedure is often termed limp home. A serious fault occurs when the signal from the sensor
is outside of its normal operating parameters.
When operating in LOS the engine may actually run quite well with failure of one or more minor sensors. Since the substituted
values are those of a hot engine, cold starting and running during the warm-up period may be less than satisfactory."
im still convinced you have an electrical problem, probably blue temp sensor wiring. I was reading this last night about motronic 1.3:
"Limited Operating Strategy (LOS)
In the event of a serious fault in one or more of the sensors or their wiring circuits, Motronic will substitute a fixed default value in
place of the defective sensor. This procedure is often termed limp home. A serious fault occurs when the signal from the sensor
is outside of its normal operating parameters.
When operating in LOS the engine may actually run quite well with failure of one or more minor sensors. Since the substituted
values are those of a hot engine, cold starting and running during the warm-up period may be less than satisfactory."

-
ross2009
- E30 Zone Addict

- Posts: 2762
- Joined: Mon Nov 19, 2007 11:00 pm
- Location: In my beemer MAN !!!! st neots CAMBS
i had same sort of problem a couple of years bk some times wouldnt start at all i had my mate put it on his comp on it and all he kept saying is that is was he blue temp sensor but infact it wasnt it was a bad earth to the blue sensor the diagnostics dont tell you that they hardly tell you anything
if youve replaced everything its gotta a be a wiring problem
if youve replaced everything its gotta a be a wiring problem
-
325isparda
- E30 Zone Newbie

- Posts: 105
- Joined: Thu Jun 02, 2011 11:00 pm
- Location: Essex
Right, hello again everyone. The past couple of weeks i have been doing the odd bits and bobs till this weekend when i decided right it's time to check the loom. So i got a friend to help me out and i have got current running throughout the entire wiring loom to the blue switch, afm, tps, icv. So i am certain it is nothing to dow ith the wiring and nothing to do with the blue temp switch.
I am officially completely out of idea, only thing i am thinking of doing is changing the ecu as when the diagnostics was done it came back with no faults, surely a 22 year old car would have some faults lol.
But yes i am stumped, o and i recently changed the inlet manifold gaskets and the breather pipe underneath it....
I am officially completely out of idea, only thing i am thinking of doing is changing the ecu as when the diagnostics was done it came back with no faults, surely a 22 year old car would have some faults lol.
But yes i am stumped, o and i recently changed the inlet manifold gaskets and the breather pipe underneath it....
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
check the rocker gasket and all air pipes, also check the throttle to inlet gasket as well.
the rubber pipe to the rocker cover is often a culprit.
the rubber pipe to the rocker cover is often a culprit.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
-
e301988325i
- E30 Zone Addict

- Posts: 3701
- Joined: Fri Feb 01, 2008 11:00 pm
- Location: Taunton, Somerset
My general concern is that a lot parts have been replaced without being diagnosed as faulty, as you've thrown 2 AFM's at it which are hundreds new it's unlikely you've used all new parts, give us a list of new and used parts that have been used. Have you checked the ECU, the car may have a quality ebay chip in ruining everything!!!
Have you had the car on an exhaust gas analyser? The AFM could just be set in such a manner to make your car run extremely rich, if the AFM was adjusted to cure an air leak then fixing that air leak would cause rich running.
Check the ICV both physically for ease of movement and electronically, 20ohms from centre to each outside pin, 40 ohms across the outside pins.
Take the oil filler cap off whilst the engine is idling, if it makes little or no difference then there's an air leak that needs sealing.
Check that the fuel pressure regulator is not leaking petrol into the vacuum hose.
Then you're into removing the injectors, checking the spray pattern is matched evenly and are not clogged or leaking.
Have you had the car on an exhaust gas analyser? The AFM could just be set in such a manner to make your car run extremely rich, if the AFM was adjusted to cure an air leak then fixing that air leak would cause rich running.
Check the ICV both physically for ease of movement and electronically, 20ohms from centre to each outside pin, 40 ohms across the outside pins.
Take the oil filler cap off whilst the engine is idling, if it makes little or no difference then there's an air leak that needs sealing.
Check that the fuel pressure regulator is not leaking petrol into the vacuum hose.
Then you're into removing the injectors, checking the spray pattern is matched evenly and are not clogged or leaking.
I said:
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
-
mrLEE30
- E30 Zone Team Member

- Posts: 6589
- Joined: Tue Jan 18, 2005 11:00 pm
- Location: Sweating buckets in Bahrain
i would like to know how you checked for current in the sensor wiring, what did you use? A clamp on meter, a CT? was it able able to measure DC milliamps? Or did you measure for voltage?Brianmoooore wrote:Brianmoooore wrote:Measure the blue temp, sensor resistance, cold and hot, at the ECU plug (above the driver's right knee).
Assuming you do mean voltage then this is why brian suggests you check the blue temp sensor at the ECU. the sensor changes the input voltage at the ECU depending on its resistance and the ECu adjusts fueling accordingly, there is little or no current to measure.
remove the ECU plug and identify pin 45 and pin 2 on the cable side( pin 45 should be brown/red wire going to it, pin 2 has brown)
then set you meter to measure resistance.
with the engine completely cold measure from the pin 45 to ground, and then from pin 45 to pin 2, the resistance should be about 2-3000 ohms for each case. now refit and run the car till hot, remove and re measure and you should have 2-300 ohms for each case. If this does not happen then report you findings.
If it does then only NOW you can eliminate the blue temp sensor and its wiring.
doing this simple and free test will eliminate many potential faults or identify where to look next. The answer is not to throw parts at the engine hoping one of them sticks!!! this is an expensive way of fault diagnosis!!!!
good luck

-
hennared323i
- Old Skooler

- Posts: 2349
- Joined: Wed Jul 25, 2007 11:00 pm
ThismrLEE30 wrote:i would like to know how you checked for current in the sensor wiring, what did you use? A clamp on meter, a CT? was it able able to measure DC milliamps? Or did you measure for voltage?Brianmoooore wrote:Brianmoooore wrote:Measure the blue temp, sensor resistance, cold and hot, at the ECU plug (above the driver's right knee).
Assuming you do mean voltage then this is why brian suggests you check the blue temp sensor at the ECU. the sensor changes the input voltage at the ECU depending on its resistance and the ECu adjusts fueling accordingly, there is little or no current to measure.
remove the ECU plug and identify pin 45 and pin 2 on the cable side( pin 45 should be brown/red wire going to it, pin 2 has brown)
then set you meter to measure resistance.
with the engine completely cold measure from the pin 45 to ground, and then from pin 45 to pin 2, the resistance should be about 2-3000 ohms for each case. now refit and run the car till hot, remove and re measure and you should have 2-300 ohms for each case. If this does not happen then report you findings.
If it does then only NOW you can eliminate the blue temp sensor and its wiring.
doing this simple and free test will eliminate many potential faults or identify where to look next. The answer is not to throw parts at the engine hoping one of them sticks!!! this is an expensive way of fault diagnosis!!!!
good luck
-
d1mkaz
- E30 Zone Regular

- Posts: 794
- Joined: Thu Jan 03, 2008 11:00 pm
- Location: London
I know that everything is checked and changed but I must mention that had very similar problem last year, had 2 afm's replaced too
, at the end it was a crack in a distributor cap.
-
325isparda
- E30 Zone Newbie

- Posts: 105
- Joined: Thu Jun 02, 2011 11:00 pm
- Location: Essex
I can deffinately understand where everyone is coming from, unfortunately im not to good with the technical lingo lol. Just to defend myself, i started throwing parts at it because i was worried that if i didnt do something quick then i could cause more damage and becuase it was running fine when it was rebuilt i thought it could only ever be something to do with the vacuum, what also helps is that i work for a motorfactors so the majority of parts i get are rather cheap.
Me and my father in law checked the wiring loom by unpluggling it from the ecu and checking the current from the plug to the sensors on the afm, icv, tps etc. He then checked the readings that the sensor was giving of when cold and hot using what you have all said on here as a guide. We double checked the plug underneath the inlet to make sure there was a good current running through there and then to top it off me being a bit forgetfull i forgot to attatch the plug back onto the sensor when i was leaving and the car kept on dying, i was really confused at this point then realised i had forgotten to plug it back in haha.
I will double check the findings with the old git tonight (hoping he has remembered) and give you the readings we have found. The afm each time i have changed it has been gas tested and adjusted to meet requirments with a good mixture. I will give you a list of what is new and second hand that i have changed.
New:
TPS
ICV
Vacuum Hose (AFM to throttle body)
Inlet Manifold Gasktes
Breather Pipe
Fuel Pipes
Fuel Filter
Distributor
Rotor Arm
Plugs
Leads
Relays
Fuses
Second hand:
Fuel Pressure Regulator.
Afm... That is all lol
Thankyou for everyone for helping, i am sorry im not so technical with the whole electrics side, but i am trying lol
Hopefully it will get sorted soon, i am trying to source an ecu with the same part number as mine to see if i can just try and see whether my ecu is faulty, and after what D1mkaz said i may double check my dizzy and make sure it is not faulty.
Me and my father in law checked the wiring loom by unpluggling it from the ecu and checking the current from the plug to the sensors on the afm, icv, tps etc. He then checked the readings that the sensor was giving of when cold and hot using what you have all said on here as a guide. We double checked the plug underneath the inlet to make sure there was a good current running through there and then to top it off me being a bit forgetfull i forgot to attatch the plug back onto the sensor when i was leaving and the car kept on dying, i was really confused at this point then realised i had forgotten to plug it back in haha.
I will double check the findings with the old git tonight (hoping he has remembered) and give you the readings we have found. The afm each time i have changed it has been gas tested and adjusted to meet requirments with a good mixture. I will give you a list of what is new and second hand that i have changed.
New:
TPS
ICV
Vacuum Hose (AFM to throttle body)
Inlet Manifold Gasktes
Breather Pipe
Fuel Pipes
Fuel Filter
Distributor
Rotor Arm
Plugs
Leads
Relays
Fuses
Second hand:
Fuel Pressure Regulator.
Afm... That is all lol
Thankyou for everyone for helping, i am sorry im not so technical with the whole electrics side, but i am trying lol
Hopefully it will get sorted soon, i am trying to source an ecu with the same part number as mine to see if i can just try and see whether my ecu is faulty, and after what D1mkaz said i may double check my dizzy and make sure it is not faulty.
-
popey7676
- E30 Zone Regular

- Posts: 301
- Joined: Fri Jan 15, 2010 11:00 pm
- Location: Devon
When the camshaft was changed, where all the clips that hold the rockers correctly fitted, inline with the grooves? might be worth checking!
-
325isparda
- E30 Zone Newbie

- Posts: 105
- Joined: Thu Jun 02, 2011 11:00 pm
- Location: Essex
hmmm, I can double check that tonight, Just out of interest what would that cause?
-
popey7676
- E30 Zone Regular

- Posts: 301
- Joined: Fri Jan 15, 2010 11:00 pm
- Location: Devon
well if one was loose then it would certainly make the engine run rough, worth checking!
-
hongkongfuey
- Mad-tango-geezer
- Posts: 3303
- Joined: Fri Jun 08, 2007 11:00 pm
- Location: portsmouth
just a thought , have you adjusted the tappets? if you have one tight that maybe holding a valve slightly open, you said one compression was slow to build up?
if there wern't people like me,
with cars like mine,
who would you put down to make yourself feel better?
with cars like mine,
who would you put down to make yourself feel better?
-
mrLEE30
- E30 Zone Team Member

- Posts: 6589
- Joined: Tue Jan 18, 2005 11:00 pm
- Location: Sweating buckets in Bahrain
You cannot measure current in a circuit with it unplugged as you describe as by unplugging you break the loop- thus current cannot flow, the only easily measureable parameters are voltage and resistance. With this you can measure if a sensor is getting the correct voltage, the resistance shows you continuity/open circuit and resistance- but even these can be misleading to those who do not fully understand what they are doung( don't worry you are not alone with this!!)
Did you measure as Brian said and I describe? If you do not understand what I mean or how to measure resistance let me know what meter you have (or a picture) and we can help you to measure it.
Did you measure as Brian said and I describe? If you do not understand what I mean or how to measure resistance let me know what meter you have (or a picture) and we can help you to measure it.

-
325isparda
- E30 Zone Newbie

- Posts: 105
- Joined: Thu Jun 02, 2011 11:00 pm
- Location: Essex
I would just like to say thankyou to everyone that helped me out on this problem, i know i was hard to work with lol.
Its all sorted now, Even though i had changed the AFM and had it tested i changed it once more for one i new was working and then got it on the gas analyser, the next moring it was working perfectly with no problems.
Once again though thankyou to everyone that helped

Its all sorted now, Even though i had changed the AFM and had it tested i changed it once more for one i new was working and then got it on the gas analyser, the next moring it was working perfectly with no problems.
Once again though thankyou to everyone that helped

