Cleaning TPS \ Removing Problems
Moderator: martauto
-
Rtaylor2208
- E30 Zone Addict

- Posts: 3004
- Joined: Mon Oct 11, 2010 11:00 pm
- Location: Ayr, Ayrshire, Scotland
Hi Folks, Been trying to diagnose the running rich problems on the car and it looks like the TPS has an issue going on the wiki.
Removed the Airbox, ICV, intake rubber and the boot the pipe comming from the head.
The problems I have now are:
1. I cant get the bloody rubber hoses off that are on the right hand side of the throttle body. It looks like they go to the back of the car. The pipes still have all the origiaal clamps on them which look like the usual jubilees but have no adjuster so how do you loosen them?
2. The star headed screws that hold on the TPS Sensor to the TB are rotted so cant unscrew them, cant bloddy drill them out either without getting the pipes off.
Help Please!!!!
Removed the Airbox, ICV, intake rubber and the boot the pipe comming from the head.
The problems I have now are:
1. I cant get the bloody rubber hoses off that are on the right hand side of the throttle body. It looks like they go to the back of the car. The pipes still have all the origiaal clamps on them which look like the usual jubilees but have no adjuster so how do you loosen them?
2. The star headed screws that hold on the TPS Sensor to the TB are rotted so cant unscrew them, cant bloddy drill them out either without getting the pipes off.
Help Please!!!!
-
e301988325i
- E30 Zone Addict

- Posts: 3701
- Joined: Fri Feb 01, 2008 11:00 pm
- Location: Taunton, Somerset
Which engine??????????????????????
Star headed screws are philips/posidrive from the factory. if it's M20 you don't have to remove the pipes there' plenty of movement on them.
Star headed screws are philips/posidrive from the factory. if it's M20 you don't have to remove the pipes there' plenty of movement on them.
I said:
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
-
Rtaylor2208
- E30 Zone Addict

- Posts: 3004
- Joined: Mon Oct 11, 2010 11:00 pm
- Location: Ayr, Ayrshire, Scotland
Sorry its M20 325i
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Hoses on the RH side of the TB are to the brake servo valve. Get a small screwdriver in the 'hump' on the clip and twist it to open the 'hump' up, or cut through the hump. Replace with ordinary jubilee clips. There's another sort of clip that looks similar and might be fitted. With these the 'hump' is hooked over the other end of the clip, and, in the absence of the correct tool can be undone and refitted with side cutters.
You don't need to remove the TPS from the TB. You can drill the drain and flush it out with it still attached. You won't be able to adjust it, but as yet, you have no evidence to sufggest it needs adjustment.
You don't need to remove the TPS from the TB. You can drill the drain and flush it out with it still attached. You won't be able to adjust it, but as yet, you have no evidence to sufggest it needs adjustment.
Last edited by Brianmoooore on Tue Nov 15, 2011 7:26 pm, edited 1 time in total.
-
Rtaylor2208
- E30 Zone Addict

- Posts: 3004
- Joined: Mon Oct 11, 2010 11:00 pm
- Location: Ayr, Ayrshire, Scotland
Brian, for drilling a hole where should I do that? On the Sensor its self there is a round circle dead centre is that where it would go? Anything to be carefull of?
The reason for looking at this is there is no clicking sound as described in the wiki when the throttle is pressed.
The reason for looking at this is there is no clicking sound as described in the wiki when the throttle is pressed.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Right in the centre of the circle. Don't let the drill bit penetrate inside, or let swarf in, and use the smallest bit you have.
-
Rtaylor2208
- E30 Zone Addict

- Posts: 3004
- Joined: Mon Oct 11, 2010 11:00 pm
- Location: Ayr, Ayrshire, Scotland
Thanks Brian doesn't sound too difficult. I'll give it a try tomorrow night just been called out by the work.
-
Rtaylor2208
- E30 Zone Addict

- Posts: 3004
- Joined: Mon Oct 11, 2010 11:00 pm
- Location: Ayr, Ayrshire, Scotland
Brian I have drilled a 2mm hole in the centre, after leaving it for a few hours nothing has came out. What should I try next to test its working as it should?
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Get some isopropyl alcohol in there, or some proprietary switch cleaner.
-
Rtaylor2208
- E30 Zone Addict

- Posts: 3004
- Joined: Mon Oct 11, 2010 11:00 pm
- Location: Ayr, Ayrshire, Scotland
I only have carb cleaner and penetrating fluid handy I take I cant use either of them?
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
The carb. cleaner should do the job.
-
Mikey_Boy
- E30 Zone Regular

- Posts: 996
- Joined: Sun Mar 16, 2008 11:00 pm
- Location: Cheshire - trying to avoid the bling!
Have a look here as well:
http://www.e30zone.net/modules.php?name ... c&t=153524
There is a really useful section on how to test the TPS to see if its working. I thought mine was shot, but with a bit of care it can be stripped and rebuilt.
Good luck!

http://www.e30zone.net/modules.php?name ... c&t=153524
There is a really useful section on how to test the TPS to see if its working. I thought mine was shot, but with a bit of care it can be stripped and rebuilt.
Good luck!
-
Rtaylor2208
- E30 Zone Addict

- Posts: 3004
- Joined: Mon Oct 11, 2010 11:00 pm
- Location: Ayr, Ayrshire, Scotland
Thanks Mikey_boy, but the TPS can't be removed at the moment as the screws holding it to TB have rotted.
Brian will give it a bash with carb cleaner tonight and post back.
Brian will give it a bash with carb cleaner tonight and post back.
-
e301988325i
- E30 Zone Addict

- Posts: 3701
- Joined: Fri Feb 01, 2008 11:00 pm
- Location: Taunton, Somerset
I've dismantled, bored and rebuilt 15 M20 throttle bodies, I have never seen those bolts rusted to bits or even found one stuck, you'll need to get the throttle body off the manifold studs and turn it to get decent access to them with a screwdriver.Rtaylor2208 wrote:Thanks Mikey_boy, but the TPS can't be removed at the moment as the screws holding it to TB have rotted.
I said:
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
-
Mikey_Boy
- E30 Zone Regular

- Posts: 996
- Joined: Sun Mar 16, 2008 11:00 pm
- Location: Cheshire - trying to avoid the bling!
^^^
+1 - best to get the throttle body off - that's how I did mine...
My screws were pretty scrap as well - I drilled them out carefully and ran a tap through the holes to clean them up..
+1 - best to get the throttle body off - that's how I did mine...
My screws were pretty scrap as well - I drilled them out carefully and ran a tap through the holes to clean them up..
-
Rtaylor2208
- E30 Zone Addict

- Posts: 3004
- Joined: Mon Oct 11, 2010 11:00 pm
- Location: Ayr, Ayrshire, Scotland
Throttle body is off at the moment just the two pipes that connect to the brake servo part are still connected giving me good access but both heads have rotted so chewed up when I tried to remove them. For the moment drilling out the screws is a last resort, waiting to see if I can get it working via cleaning as per mr moore's suggestion.
-
pacerpete
- E30 Zone Team Member

- Posts: 18165
- Joined: Sun Jan 23, 2005 11:00 pm
- Location: Iver heath. South bucks.
The TPS has a removeable cover, they can be carefully prised off in situ and a carefully aimed jet of carb/ brake cleaner aimed at the innards of the TPS unit whilst you open and shut the throttle. Once you hear the switch clicking as the thottle comes on / off idle you are in business, assuming a meathead hasn't wound up the throttle stop screw.......
The TPS cover can now be cleaned and drilled if you wish and reattached. If the cover is a little 'distressed' a couple of dabs of glue should keep it secure.
This method works a treat and saves removing the throttle body.
The TPS cover can now be cleaned and drilled if you wish and reattached. If the cover is a little 'distressed' a couple of dabs of glue should keep it secure.
This method works a treat and saves removing the throttle body.
-
Rtaylor2208
- E30 Zone Addict

- Posts: 3004
- Joined: Mon Oct 11, 2010 11:00 pm
- Location: Ayr, Ayrshire, Scotland
Thanks Pacerpete. I was out tonight spraying carb cleaner into the hole I had already drilled but no joy. I'll have a try at getting the cover off on saturday.
-
Mikey_Boy
- E30 Zone Regular

- Posts: 996
- Joined: Sun Mar 16, 2008 11:00 pm
- Location: Cheshire - trying to avoid the bling!
Remember as well to check continuity approaching wide open throttle as well - this is just as important as checking the idle switch clicks as continuity at each end ensures the Motronic 'sees' the right map as it goes through the throttle travel - not quite as good as a proper throttle pot, but back in the day...
IIRC, I had to resolder a joint and also tweek the position of the TPS a little to get the setting right - pretty easy repair if I recall - you can go from zero to hero with care!!
Then all you have to tackle are the remaining air leaks and you are in business!!
IIRC, I had to resolder a joint and also tweek the position of the TPS a little to get the setting right - pretty easy repair if I recall - you can go from zero to hero with care!!
Then all you have to tackle are the remaining air leaks and you are in business!!
-
Rtaylor2208
- E30 Zone Addict

- Posts: 3004
- Joined: Mon Oct 11, 2010 11:00 pm
- Location: Ayr, Ayrshire, Scotland
Pretty sure there are no air leaks as spent a few hours going over every joint and hose with carb cleaner, also replaced the big rubber intake with a new one from BMW as it had some splits in it.
For testing the continuty have you any guides for it the TPS connection is a round plug with about 6 pins on it and the bently manual shows a different type of connection.
For testing the continuty have you any guides for it the TPS connection is a round plug with about 6 pins on it and the bently manual shows a different type of connection.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Now you tell us!Rtaylor2208 wrote: the TPS connection is a round plug with about 6 pins on it and the bently manual shows a different type of connection.
This is the TPS for a switch able auto, and is a combined unit of an ordinary E30 TPS, plus a throttle position pot., as used on the M42 iS and later BMWs.
The two parts are entirely electrically separate, and the pot. section is only used by the gearbox.
The switch section operates exactly as a normal one, but I've no idea if the construction is such that it can be cleaned in the same way.
I don't have the pin connections for this unit, but the switch wire colours are the same as other E30s, or you can just find the correct pins by experiment - there's only six pins.
-
Rtaylor2208
- E30 Zone Addict

- Posts: 3004
- Joined: Mon Oct 11, 2010 11:00 pm
- Location: Ayr, Ayrshire, Scotland
Sorry Brian didn't realise that it was differnt on an auto
. Looks like it will be some trial an error?
-
e301988325i
- E30 Zone Addict

- Posts: 3701
- Joined: Fri Feb 01, 2008 11:00 pm
- Location: Taunton, Somerset
Can confirm, drill and clean in the same way, do not advise removing cover. i have one fitted to my manual to give the LPG ECU a better signal (this tunrned out to be a waste of time and effort)
The TPS is sealed on to the throttle body, it is unlikely the oil (if any) will drain until the TPS is removed.
Basically the unit is taller than the manual version. Due to the combination of two different TPS the idle click is harder to hear and slightly more difficult to set.
Be carefull not to damage the TPS, they are not that common and are very expensive new.
3 pins for each switch, each switch has it's own 5v live. 1-3 autobox, 4-6 engine
Pin 1-black wire-5volt in
Pin 2- brown shielded wire-ground
Pin 3-yellow wire-signal out
Pin 4- +5v
Pin 5- Brown/Black - WOT switch
Pin 6- Brown/blue - idle switch
The TPS is sealed on to the throttle body, it is unlikely the oil (if any) will drain until the TPS is removed.
Basically the unit is taller than the manual version. Due to the combination of two different TPS the idle click is harder to hear and slightly more difficult to set.
Be carefull not to damage the TPS, they are not that common and are very expensive new.
3 pins for each switch, each switch has it's own 5v live. 1-3 autobox, 4-6 engine
Pin 1-black wire-5volt in
Pin 2- brown shielded wire-ground
Pin 3-yellow wire-signal out
Pin 4- +5v
Pin 5- Brown/Black - WOT switch
Pin 6- Brown/blue - idle switch
I said:
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
-
Rtaylor2208
- E30 Zone Addict

- Posts: 3004
- Joined: Mon Oct 11, 2010 11:00 pm
- Location: Ayr, Ayrshire, Scotland
Thanks e301988325i, I'm starting to think this may be more difficult than I have the skill for.
If only I could get the TPS removed really dont want to have to drill out the rotted screws in case I truly f**k things up.
If only I could get the TPS removed really dont want to have to drill out the rotted screws in case I truly f**k things up.
-
pacerpete
- E30 Zone Team Member

- Posts: 18165
- Joined: Sun Jan 23, 2005 11:00 pm
- Location: Iver heath. South bucks.
Rtaylor2208 wrote:Thanks e301988325i, I'm starting to think this may be more difficult than I have the skill for.
If only I could get the TPS removed really dont want to have to drill out the rotted screws in case I truly f**k things up.
Have you tried removing the cover ? Its even easier on an auto.
Its not a 'bodge' and if it works (it always does for me) you have saved yourself lots of drama.
Be sure to operate the throttle as you spray the brake cleaner as it will exercise the microswitch and hopefully get all the oil out.
I assume your problem is idle related and you cannot hear the idle micro switch clicking ? If not, your problem is probably not TPS related.
I have NEVER changed a fooked one but I have cleaned and reset loads where time(oil contamination) and beasts with screw drivers have taken their toll.
-
Rtaylor2208
- E30 Zone Addict

- Posts: 3004
- Joined: Mon Oct 11, 2010 11:00 pm
- Location: Ayr, Ayrshire, Scotland
Pete thanks for the advice no harm in trying. Whih part of the cover is it just the top edge where the round bit is or closer to where it attaches to the TB.
Yep no clicking noise at all and it is an idle issue I am trying to resolve.
Have changed the plugs, replaced the AFM boot as it had a massive air leak, checked all other hoses for leaks, also cleaned out the ICV and AFM (no gurantee someoness hasn't fecked with the screw before though) , checked the blue temp sensor at the sensor itself still to try at the ecu end.
Just incase I've posted up a wanted add for a TB with the TPS attached and working as a feeler if all else fails.
Yep no clicking noise at all and it is an idle issue I am trying to resolve.
Have changed the plugs, replaced the AFM boot as it had a massive air leak, checked all other hoses for leaks, also cleaned out the ICV and AFM (no gurantee someoness hasn't fecked with the screw before though) , checked the blue temp sensor at the sensor itself still to try at the ecu end.
Just incase I've posted up a wanted add for a TB with the TPS attached and working as a feeler if all else fails.
-
Rtaylor2208
- E30 Zone Addict

- Posts: 3004
- Joined: Mon Oct 11, 2010 11:00 pm
- Location: Ayr, Ayrshire, Scotland
Hope pacerpete or Mr Moore are on today,
I managed to get the cover off of the TPS. The gold connection that rotates within the switch is not connecting with the micro swtich so that would explain the lack of a click.
How do I adjust this? For anyone else reading the TPS is still attached to the TB and I have the top cover off.
Would love to get this sorted today if anyone can help explain what to do?
I managed to get the cover off of the TPS. The gold connection that rotates within the switch is not connecting with the micro swtich so that would explain the lack of a click.
How do I adjust this? For anyone else reading the TPS is still attached to the TB and I have the top cover off.
Would love to get this sorted today if anyone can help explain what to do?
-
Rtaylor2208
- E30 Zone Addict

- Posts: 3004
- Joined: Mon Oct 11, 2010 11:00 pm
- Location: Ayr, Ayrshire, Scotland
Having kust read the mototronic sticky it looks like some fuck wit has adjusted the throttle stop at some point and successfully managed to snap the head off the bolt so I cant adjust it.
Fortuntaly another zoner has offered us a TPS and TB which are the ones I need so time to give up on fixing the sensor.
Thanks to everyone who gave me advice.
Fortuntaly another zoner has offered us a TPS and TB which are the ones I need so time to give up on fixing the sensor.
Thanks to everyone who gave me advice.
