Need technical Q/A then you're in the right place
Moderator: martauto
-
snott
- E30 Zone Newbie

- Posts: 27
- Joined: Thu Feb 24, 2011 11:00 pm
Post
Thu Nov 17, 2011 2:14 pm
hi
ive read wiki e30 page about the central locking and searched the tech page but im still stuck.
im trying to unplug the plug from the door to the body and its totally stuck. ive tried prying it out with a screwdriver but just ended up cracking the plastic. any ideas?
also when i took out the box of tricks for the central locking i notice a plug which looked like something is missing-could this be why my central locking isnt work?

-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
Post
Thu Nov 17, 2011 2:19 pm
Pull the rubber boot off the A pillar socket first,then squeeze the tabs in,the plug should slide out.They are made to be a tight fit....
That 'spare' plug that you have found is probably for an interior light delay unit.
Have you carried out the red/black wire mod as suggested in the wiki?
What is wrong with your central locking?
Youth is wasted on the young.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Post
Thu Nov 17, 2011 7:08 pm
There should be a little plastic piece that pushes into the back end of the plug, that has to be removed before you can release the tabs, but these are often missing.
The rubber cover must be refitted over the plug BEFORE the plug is pushed back into the socket.
-
BenHar
- E30 Zone Addict

- Posts: 3089
- Joined: Sun Jul 11, 2010 11:00 pm
- Location: Reigate, Surrey
Post
Thu Nov 17, 2011 7:14 pm
Brianmoooore wrote:There should be a little plastic piece that pushes into the back end of the plug, that has to be removed before you can release the tabs, but these are often missing.
Has any one got a picture of this "little plastic piece".
Mine are stuck, too.
Thanks
Ben
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Post
Thu Nov 17, 2011 7:25 pm
From memory, it's rectangular, with rounded corners, about 20mm x 10mm, flat one side, and has three projecting circles on the other side. Quite obvious that you can't squeeze the tabs in properly with it in place.
Grip the tabs with two pairs of pliers, squeeze them inwards towards each other and pull.
-
BenHar
- E30 Zone Addict

- Posts: 3089
- Joined: Sun Jul 11, 2010 11:00 pm
- Location: Reigate, Surrey
Post
Thu Nov 17, 2011 7:28 pm
Ah, that bit. When you said on the back I thought you meant inside the A pillar, but that would be the front, of course.
Thanks
Ben
-
snott
- E30 Zone Newbie

- Posts: 27
- Joined: Thu Feb 24, 2011 11:00 pm
Post
Fri Nov 18, 2011 8:20 am
ive tried squeezing the two tabs in but its stuck solid and has started to crack. i havent done the red/black wire mod yet.
the problem with the central locking is its not working, so im going through everything that could be wrong.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Post
Fri Nov 18, 2011 8:32 am
Unless this plug and socket have been proved to be faulty, then it's best left alone!
Do the red/black wire mod.
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
Post
Fri Nov 18, 2011 11:23 am
snott wrote:ive tried squeezing the two tabs in but its stuck solid and has started to crack. i havent done the red/black wire mod yet.
the problem with the central locking is its not working, so im going through everything that could be wrong.
After carrying out the red/black wire mod,if the c/l is still inactive,my next check would be the thermal fuse link within the c/l relay unit.
Youth is wasted on the young.
-
snott
- E30 Zone Newbie

- Posts: 27
- Joined: Thu Feb 24, 2011 11:00 pm
Post
Fri Nov 18, 2011 1:58 pm
ok i'll do the r/b wire mod over the weekend
thanks for your help
-
snott
- E30 Zone Newbie

- Posts: 27
- Joined: Thu Feb 24, 2011 11:00 pm
Post
Sat Nov 19, 2011 2:17 pm
yep got it working, the r/b mod solved it
thanks