removing rear subframe clean, how to?
Moderator: martauto
-
bmw9818
- E30 Zone Addict

- Posts: 2561
- Joined: Tue Aug 11, 2009 11:00 pm
- Location: Croydon
attempted to get the disc arms off a touring, removed drive shaft, arb, and shock, if you get the bolt of on the outside, theres hardly any room to move a spanner on the inside bolt,
so far removing the subframe ive accounted for -
4 6mm hex bolts both sides,
22mm subframe bolt,
hbrake cables/ brake lines,
8mm driveshaft bolts,
shocks + arb
where im getting confused is the diff, do i need to remove it? theres one bolt holding it on the bush, do i remove this, how many bolts connect the prop to the diff, and ive noticed in pics there are four bolt holes at the top of the diff, and theres a metal plate thing?
do i get to these bolts from underneath, do they go all the way through and bolt to the chassis,
once i start i cant really stop so need to make sure i can actually do it before i get going,
also once the subframe bolts are out what do you do then smack the pins from the bottom?
so far removing the subframe ive accounted for -
4 6mm hex bolts both sides,
22mm subframe bolt,
hbrake cables/ brake lines,
8mm driveshaft bolts,
shocks + arb
where im getting confused is the diff, do i need to remove it? theres one bolt holding it on the bush, do i remove this, how many bolts connect the prop to the diff, and ive noticed in pics there are four bolt holes at the top of the diff, and theres a metal plate thing?
do i get to these bolts from underneath, do they go all the way through and bolt to the chassis,
once i start i cant really stop so need to make sure i can actually do it before i get going,
also once the subframe bolts are out what do you do then smack the pins from the bottom?
Last edited by bmw9818 on Sun Nov 13, 2011 8:41 pm, edited 2 times in total.
-
greggers
- E30 Zone Newbie

- Posts: 135
- Joined: Mon Jul 04, 2011 11:00 pm
Did this job yesterday with the back of the car on axle stands, whilst not easy it is possible.
We used a pretty slender set of spanners to get on the nuts on the bolts nearest the outside of the car. With the spring off and a spanner on the other side you can use the trailing arms as leverage.
You don't need to chop the hand-brake cables whatever you do, they are simply removed from the drums.
When you look for arms, don't fall in the trap we found ourselves in at the weekend with one good late arm, one good early arm, a shagged early arm and new bearings for the late arm.
We used a pretty slender set of spanners to get on the nuts on the bolts nearest the outside of the car. With the spring off and a spanner on the other side you can use the trailing arms as leverage.
You don't need to chop the hand-brake cables whatever you do, they are simply removed from the drums.
When you look for arms, don't fall in the trap we found ourselves in at the weekend with one good late arm, one good early arm, a shagged early arm and new bearings for the late arm.
-
bmw9818
- E30 Zone Addict

- Posts: 2561
- Joined: Tue Aug 11, 2009 11:00 pm
- Location: Croydon
where abouts did you stick the stands?,
im thinking to just drop the subframe as it seems it would be a bit more easier, the spring is in the way of the spanner, and seeing as ive got some ancient wind up compressors its gonna take bloody long to compress those,
once its dropped i can just change the arms over on the floor i suppose,
im thinking to just drop the subframe as it seems it would be a bit more easier, the spring is in the way of the spanner, and seeing as ive got some ancient wind up compressors its gonna take bloody long to compress those,
once its dropped i can just change the arms over on the floor i suppose,
-
greggers
- E30 Zone Newbie

- Posts: 135
- Joined: Mon Jul 04, 2011 11:00 pm
Er, why have you still got the springs in situe? You don't need to compress them to get them out just undo the bolt on the bottom of the shock and release the anti roll bar.
This is one area where the Haynes manual actually gives a half decent explanation of the process.
This is one area where the Haynes manual actually gives a half decent explanation of the process.
-
bmw9818
- E30 Zone Addict

- Posts: 2561
- Joined: Tue Aug 11, 2009 11:00 pm
- Location: Croydon
there the original springs, they wont pull out its on there pretty tight, ive removed the shock and arb, trailing arms been dropped right down, it aint coming out,
-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
drop the whole lot
4x nuts from propshaft to diff
one nut&bolt going through diff bush
2x ARB to trailing arm nuts
4x hex nuts
2x 22m subframe
2x shock nut
cut the 2x brake lines from trailing arm to chassis, and the hanbrake cables
(these are easily removed when subframe is out of the way, and you need new ones anyway)
I think that's all, then lower it all on the trolley jack, from the diff.
4x nuts from propshaft to diff
one nut&bolt going through diff bush
2x ARB to trailing arm nuts
4x hex nuts
2x 22m subframe
2x shock nut
cut the 2x brake lines from trailing arm to chassis, and the hanbrake cables
(these are easily removed when subframe is out of the way, and you need new ones anyway)
I think that's all, then lower it all on the trolley jack, from the diff.
-
greggers
- E30 Zone Newbie

- Posts: 135
- Joined: Mon Jul 04, 2011 11:00 pm
Is it stuck at the top or the bottom... Either way, hit it with a hammer and I'm sure it'll move.
-
bmw9818
- E30 Zone Addict

- Posts: 2561
- Joined: Tue Aug 11, 2009 11:00 pm
- Location: Croydon
top an bottom, it aint budging, might try the hammer ting, bit cautious around springs since the compressors buckled once and nearly took my head off!
so are there no other bolts holding the diff to the body, its just the one goinf through the bush?
do i need to do anything with the subframe pins or posts under the seat? something about wacking them?
so are there no other bolts holding the diff to the body, its just the one goinf through the bush?
do i need to do anything with the subframe pins or posts under the seat? something about wacking them?
-
greggers
- E30 Zone Newbie

- Posts: 135
- Joined: Mon Jul 04, 2011 11:00 pm
Diff to body is just the bush bolt, the other 4 are to the subframe.
The springs should be fully expanded, so there shouldn't be any tension in them, you shouldn't need to use spring compressors at all.
The diff to subframe bolts can be a pig, can get a socket on the top two, I ended up using plus gas and a long spanner/pipe.
If you get some leverage on the trailing arm to press it down, the spring should just fall out.
The springs should be fully expanded, so there shouldn't be any tension in them, you shouldn't need to use spring compressors at all.
The diff to subframe bolts can be a pig, can get a socket on the top two, I ended up using plus gas and a long spanner/pipe.
If you get some leverage on the trailing arm to press it down, the spring should just fall out.
-
bmw9818
- E30 Zone Addict

- Posts: 2561
- Joined: Tue Aug 11, 2009 11:00 pm
- Location: Croydon
cool will give it a go tomorrow, its never as simple as it seems! we'll see what shit i get myself into tomorrow 
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Standard rear springs may still just be under a little compression with the trailing arms at full droop.
A couple of decent sized cable ties around the spring with the arm jacked back up slightly will do the trick.
Bush pins need to be hammered up into the body. Remove the rear seat cushion, and lay a large cloth over the top of the hole that the pins are in, to prevent them flying around inside the cabin if they come loose sudenly.
A couple of decent sized cable ties around the spring with the arm jacked back up slightly will do the trick.
Bush pins need to be hammered up into the body. Remove the rear seat cushion, and lay a large cloth over the top of the hole that the pins are in, to prevent them flying around inside the cabin if they come loose sudenly.
-
bmw9818
- E30 Zone Addict

- Posts: 2561
- Joined: Tue Aug 11, 2009 11:00 pm
- Location: Croydon
ermmm, all bolts are out, used a mallet pushed pins back into the car, i banged it with a hammer as much as possible its still there... put a rod in and shimmied it about, i take it its rusted on or?
im thinking 1mtre bar, leveraged on? cant really get too much of a swing at it,
im thinking 1mtre bar, leveraged on? cant really get too much of a swing at it,
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
You can try that, but there's a chance are that the bit of the alloy bush that's in the body will break off and have to be chiselled out.bmw9818 wrote:im thinking 1mtre bar, leveraged on? cant really get too much of a swing at it,
When I get an awkward one, I cut up through the rubber of the bushes both sides with two different size deep hole saws, which allows the subframe to be removed, letting you get at the remains properly.
-
bmw9818
- E30 Zone Addict

- Posts: 2561
- Joined: Tue Aug 11, 2009 11:00 pm
- Location: Croydon
if it breaks off can i breifly reattach it ? as its going to the scrappers as soon as i get at the disc trailing arms over,
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
In that case, why are you removing the subframe? You can unbolt the trailing arms with it in place, especially if the diff bush is unbolted and it's hanging down.
-
bmw9818
- E30 Zone Addict

- Posts: 2561
- Joined: Tue Aug 11, 2009 11:00 pm
- Location: Croydon
that was the initial plan, we tried it but theres not really any room to work, or put leverage on a spanner, the bolts were on too tight,
we didnt undo the diff though, i thought there are additional four bolts holding it in place?
we didnt undo the diff though, i thought there are additional four bolts holding it in place?
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
Just remove the diff bush bolt,then the axle carrier will hang lower,giving you more room for the trailing arm bolts.Still not much room,but it is do-able!bmw9818 wrote:that was the initial plan, we tried it but theres not really any room to work, or put leverage on a spanner, the bolts were on too tight,
we didnt undo the diff though, i thought there are additional four bolts holding it in place?
Youth is wasted on the young.
-
KimH
- E30 Zone Newbie

- Posts: 186
- Joined: Thu Dec 06, 2007 11:00 pm
With everything else you have removed, and if you've already removed the 32mm drive shaft nuts, why not leave the diff in place and undo the output flange bolts to allow them to drop and then knock the splined stubs back into the hubs and remove the shafts completely.
I found the best combination on the wishbone bolts was an open ended spanner on the outboard nuts to hold them and then attack the bolts with a ring spanner. Also, forget the Birmingham spanner - these thing respond to the gentle but firm pressure leverage gives. I just jacked the end of the ring spanner up for the right hand bolts and used a long tube to hang off the spanner for the left hand pair. ( I had jacked the car up and placed 3 breeze blocks on their side under each wheel to give me room ). Failing that, I've seen some spanners with a 90 degree bend that might be your answer.
I found the best combination on the wishbone bolts was an open ended spanner on the outboard nuts to hold them and then attack the bolts with a ring spanner. Also, forget the Birmingham spanner - these thing respond to the gentle but firm pressure leverage gives. I just jacked the end of the ring spanner up for the right hand bolts and used a long tube to hang off the spanner for the left hand pair. ( I had jacked the car up and placed 3 breeze blocks on their side under each wheel to give me room ). Failing that, I've seen some spanners with a 90 degree bend that might be your answer.
