Tie rod removal from steering rack

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
318lemon
E30 Zone Newbie
E30 Zone Newbie
Posts: 26
Joined: Thu Jan 06, 2011 11:00 pm
Location: Bracknell, England

Post Sat Nov 12, 2011 9:06 pm

Changing these steering bellows has opened up a can of worms...

I'm replacing the complete tie rod assemblies on both sides as per e30tech's article here:

http://www.e30tech.com/articles/steering/tierods/

drivers side is done, no problems at all. I cant undo the passenger side from the steering rack though. Its bent my molegrips and a pipe clamp! Have made absolutely sure that the folding tabs are back (i've hammered that locking washer to hell and back...)

How can i get it undone? Can't cut it i assume?
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Sat Nov 12, 2011 9:10 pm

Do you have access to a welder? You could try welding a long bar to it so you have the angle and leverage?

I'm going to be doing this on a 323i next week, which im not looking forward to :?
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Sat Nov 12, 2011 9:11 pm

You need a bloody big spanner,I think it's a 27mm open ended one.

It will be FT tight,so make sure the car is well supported before lying under it using your feet to push/kick the spanner.It's a standard thread,not a reverse one.I think that they would have been assembled with thread lock...
Youth is wasted on the young.
User avatar
318lemon
E30 Zone Newbie
E30 Zone Newbie
Posts: 26
Joined: Thu Jan 06, 2011 11:00 pm
Location: Bracknell, England

Post Sat Nov 12, 2011 9:35 pm

Really? Okay, I'm obviously not man enough :) Will be back out there in the morning to try harder.

All that force can't hurt the rack can it?
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Sat Nov 12, 2011 9:40 pm

You were man enough to do one side,other one is just the same! :D
Youth is wasted on the young.
User avatar
318lemon
E30 Zone Newbie
E30 Zone Newbie
Posts: 26
Joined: Thu Jan 06, 2011 11:00 pm
Location: Bracknell, England

Post Sun Nov 13, 2011 8:12 am

cheers DM - second time this week you've helped me out!
Alex
Married to the E30 Zone
Married to the E30 Zone
Posts: 22665
Joined: Fri Feb 11, 2005 11:00 pm
Location: Johannesburg, South Africa

Post Sun Nov 13, 2011 10:41 am

i used some mole grips tight onto it and against the wishbone to stop it moving and used a big prybar on the nut, soon shifted it :D
User avatar
e30kid6
E30 Zone Newbie
E30 Zone Newbie
Posts: 135
Joined: Thu Nov 10, 2011 11:00 pm
Location: Medway

Post Mon Nov 14, 2011 3:44 pm

I have just replaced both of mine on my 318i and it did take some welly. I had to heat it up for about 20 minutes before it budged, but reading through this you mention locking nut on the tie rod end? Mine didn't have a locking nut just the collar that clamped around it? should I be worried lol 8O
Image
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Mon Nov 14, 2011 3:52 pm

I did some today e30kid6... Same thing, one side had the locking thing, the other side didnt... The new set didnt have them either but we put them on without :mad: Not sure how it would stop them anyway but seemed ok considering the last set had one missing and didnt look to have been changed for some time and nowt in the history of the car :mad: