i will be rebuilding my injectors on the weekend, just wanted to know the voltage supplied to each injector, don't want to fry the coil.
also what would be the best way to clean it inside without ultrasonic cleaning?
Injectors
Moderator: martauto
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
there really isnt much that can be done with out ultrasonic cleaning.
im starting to wonder if my grumpy idle is bad injectors.
im starting to wonder if my grumpy idle is bad injectors.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
-
cypriot_boy_2k7
- E30 Zone Squatter

- Posts: 1641
- Joined: Mon Jan 29, 2007 11:00 pm
thats what im thinking, have you seen my recent post with all parts changed?HairyScreech wrote: im starting to wonder if my grumpy idle is bad injectors.
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
yep, iv literally just been around mine, blue sensor done, new voltage regulator, earths checked, fuel lines renewed, plugs checked, maf/iat cleaned, Tps cleaned, and i can rule out rings as it would be worse cold that hot.
im thinking im looking at an air leak of moody injectors.
what do you think, partially blocked nozels giving bad spray pattern that wont combust well at low rpm, improving as the air velocity picks up to atomize the fuel better?
im thinking im looking at an air leak of moody injectors.
what do you think, partially blocked nozels giving bad spray pattern that wont combust well at low rpm, improving as the air velocity picks up to atomize the fuel better?
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
-
cypriot_boy_2k7
- E30 Zone Squatter

- Posts: 1641
- Joined: Mon Jan 29, 2007 11:00 pm
That is exactly what im thinking. Due to being sat for so long it would not surprise me. i did have these out a few months back but didn't think nothing of it.HairyScreech wrote:what do you think, partially blocked nozels giving bad spray pattern that wont combust well at low rpm
do you know how much voltage it takes to open the injector coil?
i've read that sum are less than 12v i don't want to fry mine especially after rebuilding them. here the pic of the rebuild kit:
4 x Filter Baskets
4 x Upper O-Rings
4 x Spacer Washers
4 x Lower O-Rings
4 x Pintle Caps
i have read that i should put green grease on the baskets, What is that stuff called?
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
ok mines fixed- well not fixed but problem found.
Now sorted, i was around 2500ppm HC at idle dropping like a stone to 216ppm HC at 2000 rpm, we decided it was an air leak and went looking, seems we have found an air leak from number 1 inlet runner, its cracked the gasket by the fuel injector.
Now sorted, i was around 2500ppm HC at idle dropping like a stone to 216ppm HC at 2000 rpm, we decided it was an air leak and went looking, seems we have found an air leak from number 1 inlet runner, its cracked the gasket by the fuel injector.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
-
cypriot_boy_2k7
- E30 Zone Squatter

- Posts: 1641
- Joined: Mon Jan 29, 2007 11:00 pm
Wow major drop mate. How did your get your readings? Is it were the inlet joins to the head?
