Fitting Steering Bellows

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
318lemon
E30 Zone Newbie
E30 Zone Newbie
Posts: 26
Joined: Thu Jan 06, 2011 11:00 pm
Location: Bracknell, England

Post Tue Nov 08, 2011 12:13 pm

Hi

I need to replace my steering rack gaiters - they’re both split! Went to GSF and got a new pair but on closer inspection there appear to be two different types. The type I bought is the type on the right ”“ with the big hole that gets attached to some sort of disc on the tie rod.

The type currently fitted is like that on the left, and equally torn!

Problem is there aren’t any discs on the rod to strap the new boot too, and I cant find anywhere that sells the other type.

I shamelessly took this picture from another thread I dug up searching for an answer (hope this isn't infringing any rules, I will delete it it does), but didn’t find what I needed. Has anyone had to deal with this before? How can it be done?

Thanks

Adam
Image
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Tue Nov 08, 2011 12:59 pm

That's my oily mitt!

In order to slide your nice new gaiter on,you will need to remove the track rod end from the bottom of the strut,you will need a ball joint splitter for this.
Then unscrew the TRE from the steering arm and slide the gaiter on,secure with a couple of cable ties and replace the TRE.If you were thinking you would have measured the amount of thread that was showing on the steering arm so that you can get the TRE in the correct place.

Do,or have done,a tracking check after this work.
Youth is wasted on the young.
User avatar
318lemon
E30 Zone Newbie
E30 Zone Newbie
Posts: 26
Joined: Thu Jan 06, 2011 11:00 pm
Location: Bracknell, England

Post Tue Nov 08, 2011 1:03 pm

Thanks daimlerman - hope you didn't mind the photo theft!

I have the TRE's off and ready (they needed doing to, this is turning out to be a brand new front end on the car :roll: ) - what I'm struggling with is how to fasten the bellows to the tie rod as the hole is far to big and there is no disc to ziptie etc to?
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Tue Nov 08, 2011 1:10 pm

You,like I was,are suffering from a lack of rubber bump stop...

Only cure is a new tie rod,not expensive at about £30 was GSF,but comes complete with a new TRE!

The the inner end of the gaiter attaches to the rack housing,the outer to the rubber bump stop.If you can find my post again(clever bugger!)I think there is a piccie of the bump stop.
What brought this to my attention was the inner edge of a new front tyre rubbing on the ARB bracket...
Youth is wasted on the young.
User avatar
318lemon
E30 Zone Newbie
E30 Zone Newbie
Posts: 26
Joined: Thu Jan 06, 2011 11:00 pm
Location: Bracknell, England

Post Tue Nov 08, 2011 1:52 pm

That must have been well out to do that surely? Ouch...In my case a sticking caliper. Finding rebuild seal kits is a PITA though....

Thanks for the advice, looks like GSF are about to get a bit richer
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Tue Nov 08, 2011 2:41 pm

No,in MY photo :D to the left is a passageway through my home,direct to the street.I need full lock every time I enter or leave...record for a steering rack is held by a Renualt Kangeroo we owned at 25k miles!E30 one's do seem to last a bit longer.
Youth is wasted on the young.
User avatar
318lemon
E30 Zone Newbie
E30 Zone Newbie
Posts: 26
Joined: Thu Jan 06, 2011 11:00 pm
Location: Bracknell, England

Post Tue Nov 08, 2011 3:02 pm

:D thanks for the help