M52B28 Crank - right one?

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
jure
E30 Zone Newbie
E30 Zone Newbie
Posts: 137
Joined: Thu Aug 27, 2009 11:00 pm

Post Sat Nov 05, 2011 5:32 pm

I have crankshaft from an early single vanos 528i.

Crankshaft marks are: 2242898, 35E5 and C38.

Is this crank that has smaller counterweights?

Also, my HC Mahle M20B25 pistons paired with M20B20 130mm rods do not clear the crankshaft.

Wiki article says that skirts from some pistons need slight machining but on other hand some zone members had straight fit pistons.

My pistons cannot move any further than this:

Image

Image
HairyScreech
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6265
Joined: Sun Jan 21, 2007 11:00 pm

Post Sat Nov 05, 2011 5:57 pm

the early long skirt pistons do need a bit of a crop, about 14mm iirc, if you had the wrong crank then you would not even be able to get the 130mm rod cap on with a normal piston, you would be looking at major clearance issues that would be instantly obvious.

i had to take 20 odd mm off and use a 135 rod to clear a vanos crank.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822

m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
User avatar
gooner1
Out humping Reindeer
Posts: 13280
Joined: Fri Apr 14, 2006 11:00 pm
Location: Northampton.For my sins.

Post Sat Nov 05, 2011 5:57 pm

Jure, same ID numbers as my Crank, and my H/C Pistons do clear.
Though i'm pretty sure Dan The has stated that the casting numbers on these
are very unreliable.
Do a search using, 2242898, and it should give you some results. HTH.
Image
User avatar
jure
E30 Zone Newbie
E30 Zone Newbie
Posts: 137
Joined: Thu Aug 27, 2009 11:00 pm

Post Sat Nov 05, 2011 7:59 pm

Searched a bit and seams that I do have correct crankshaft. By correct I mean one with smaller webs. Went to the shed and compared M20B25 and this M52B28 crankshaft and the counterweights are almost the same. Crank also clears the block.

Just don't know why my Mahle pistons do not clear the crank like yours Gooner1? Hm...

Not that important. Will take couple mm off but still would like to know more.
Last edited by jure on Sat Nov 05, 2011 8:08 pm, edited 1 time in total.
Duke137
Married to the E30 Zone
Married to the E30 Zone
Posts: 7207
Joined: Sat Aug 29, 2009 11:00 pm

Post Sat Nov 05, 2011 8:01 pm

I am sure yours is the correct one for the M20 build, "C38" is ok and "NC38" isn't
How do you pronounce 'either'? I say 'either', but some say 'either'. Either is correct.
User avatar
gooner1
Out humping Reindeer
Posts: 13280
Joined: Fri Apr 14, 2006 11:00 pm
Location: Northampton.For my sins.

Post Sat Nov 05, 2011 8:04 pm

Not sure if it makes any difference but my Pistons are KS, not Mahle.
Image
User avatar
jure
E30 Zone Newbie
E30 Zone Newbie
Posts: 137
Joined: Thu Aug 27, 2009 11:00 pm

Post Sat Nov 05, 2011 8:13 pm

Probably that makes the difference. Piston height is 7.2mm on one side (intake valve) and 7.0mm on other (exhaust valve).
User avatar
jure
E30 Zone Newbie
E30 Zone Newbie
Posts: 137
Joined: Thu Aug 27, 2009 11:00 pm

Post Mon Nov 07, 2011 12:05 pm

Should I leave part of the piston that goes between crankshaft webs like this:

Image


Or shorten it all the way?
HairyScreech
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6265
Joined: Sun Jan 21, 2007 11:00 pm

Post Mon Nov 07, 2011 7:08 pm

the general consensus has been to just shorten them all the way for the long skirt b25 pistons when used with the right crank.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822

m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&