In the last week or so my M40 motor has been jerky when starting from cold, like it's running on 3 cylinders, and the acceleration been very sedate.
However, if I stop after about a mile and a half (eg. at the paper shop), then it runs as smooth as ever after re-starting.
I tried squirting carb cleaner into the AFM, and poured a bottle of valve lubricant into the oil, but they made no difference.
Any advice would be appreciated
Kangeroo M40
Moderator: martauto
-
greg124
- E30 Zone Regular

- Posts: 668
- Joined: Tue Apr 03, 2007 11:00 pm
- Location: In the pub
Schadenfreude - the German's haven't got a word for that.
-
Billwill
- E30 Zone Regular

- Posts: 363
- Joined: Sun Jun 26, 2011 11:00 pm
- Location: South Africa
Have you checked the blue sensor that sits under the intake manifold?
This is the sensor that tells the ECU the temperature, you can disconnect the sensor and measure its resistance when hot and when cold...it should change resistance between hot and cold.
There is a post nearby here somewhere covering idle issues which gives the resistance readings you would expect for the sensor.
Also check your plugs and plug leads.
This is the sensor that tells the ECU the temperature, you can disconnect the sensor and measure its resistance when hot and when cold...it should change resistance between hot and cold.
There is a post nearby here somewhere covering idle issues which gives the resistance readings you would expect for the sensor.
Also check your plugs and plug leads.
-
greg124
- E30 Zone Regular

- Posts: 668
- Joined: Tue Apr 03, 2007 11:00 pm
- Location: In the pub
Thanks Bill.
The blue sensor is a right sod to get at! As I took the car for a short trip this morning, I've been watching the resistance slowly rise as the engine cools down this afternoon. Now about four hours since I got back, the car is nearly cold (although ambient temperature farily mild), and the resistance is 2.4k ohms. This is a bit outside the resistance stated in the Wiki, but it seem to be behaving pretty much as expected.
I checked the plugs. Three are a nice light grey/brown, the other is a bit on the black side. They were all replaced just over 6000 miles ago.
The plug leads were on the car when I bought it, five and a half years ago, and they didn't look particularly new then. I guess they are looking like prime suspect at the moment.
The blue sensor is a right sod to get at! As I took the car for a short trip this morning, I've been watching the resistance slowly rise as the engine cools down this afternoon. Now about four hours since I got back, the car is nearly cold (although ambient temperature farily mild), and the resistance is 2.4k ohms. This is a bit outside the resistance stated in the Wiki, but it seem to be behaving pretty much as expected.
I checked the plugs. Three are a nice light grey/brown, the other is a bit on the black side. They were all replaced just over 6000 miles ago.
The plug leads were on the car when I bought it, five and a half years ago, and they didn't look particularly new then. I guess they are looking like prime suspect at the moment.
Schadenfreude - the German's haven't got a word for that.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Plug leads on all my E30s were on there when they were made 20+years ago. BMW plug leads don't deteriorate.
If one plug is black because it's running rich (rather than burning oil), then the relevant injector is probably faulty.
Rebuilt injectors are probably the most overlooked service item on E30s!
If one plug is black because it's running rich (rather than burning oil), then the relevant injector is probably faulty.
Rebuilt injectors are probably the most overlooked service item on E30s!
-
greg124
- E30 Zone Regular

- Posts: 668
- Joined: Tue Apr 03, 2007 11:00 pm
- Location: In the pub
Thanks Mr Moooore.
Would a faulty injector be consistant with running OK when re-started after a short run?
How effective is injector cleaner added to the fuel?
Would a faulty injector be consistant with running OK when re-started after a short run?
How effective is injector cleaner added to the fuel?
Schadenfreude - the German's haven't got a word for that.
-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
First thing I'd do is rotor arm, distributor cap and new ht leads.
That sorted mine out! Had same probs as yours
That sorted mine out! Had same probs as yours
-
Alex
- Married to the E30 Zone

- Posts: 22665
- Joined: Fri Feb 11, 2005 11:00 pm
- Location: Johannesburg, South Africa
my m43 was starting on 3 cylinders/missfiring and kangarooing if you put your foot down
turned out to be a split air intake boot, i assume the missfire as the air/fuel ratio was wrong. maybe worth checking the air hoses
turned out to be a split air intake boot, i assume the missfire as the air/fuel ratio was wrong. maybe worth checking the air hoses
-
greg124
- E30 Zone Regular

- Posts: 668
- Joined: Tue Apr 03, 2007 11:00 pm
- Location: In the pub
Thanks guys.
Rotor arm and disi cap were changed about 2 years ago, and I checked the big air hose from the AFM to the inlet manifold.
Are there any other air hoses to suspect?
Rotor arm and disi cap were changed about 2 years ago, and I checked the big air hose from the AFM to the inlet manifold.
Are there any other air hoses to suspect?
Schadenfreude - the German's haven't got a word for that.
-
Billwill
- E30 Zone Regular

- Posts: 363
- Joined: Sun Jun 26, 2011 11:00 pm
- Location: South Africa
Two other problems I had with my M40...spluttering from startup then coming right later:
-Replaced the fuel regulator. I followed the Haynes procedure and checked that the fuel pump was holding pressure but the fuel regulator was letting the fuel sink back into the tank.
--The newer M40s have an extra piece of cable...about 18 inches long...added into the connection from the AFM to the harness. This has the male/female screw connectors to enable it to slot in between the AFM and the harness. This obviously is some form of added Engineering change to smooth the output from the AFM....the "bump" in the cable actually has a small circuit board installed with an IC, transistors etc. I tried removing this extra cable section and the engine has been running well ever since....put it back and problem returns. Haynes manual makes no mention of this extra cable...when you try to measure the continuity from the AFM to the ECU you can see that the circuit inside the cable interrupts the AFM signal.
If you have this extra cable...try removing it!
About a week ago I had rough running...as I started to pull the plugs out...the one plug lead come apart at the push-on connector and showed signs of green copper type rust. I re-crimped the cable into the connector and sealed it all up with a rubber composite glue.
-Replaced the fuel regulator. I followed the Haynes procedure and checked that the fuel pump was holding pressure but the fuel regulator was letting the fuel sink back into the tank.
--The newer M40s have an extra piece of cable...about 18 inches long...added into the connection from the AFM to the harness. This has the male/female screw connectors to enable it to slot in between the AFM and the harness. This obviously is some form of added Engineering change to smooth the output from the AFM....the "bump" in the cable actually has a small circuit board installed with an IC, transistors etc. I tried removing this extra cable section and the engine has been running well ever since....put it back and problem returns. Haynes manual makes no mention of this extra cable...when you try to measure the continuity from the AFM to the ECU you can see that the circuit inside the cable interrupts the AFM signal.
If you have this extra cable...try removing it!
About a week ago I had rough running...as I started to pull the plugs out...the one plug lead come apart at the push-on connector and showed signs of green copper type rust. I re-crimped the cable into the connector and sealed it all up with a rubber composite glue.
-
greg124
- E30 Zone Regular

- Posts: 668
- Joined: Tue Apr 03, 2007 11:00 pm
- Location: In the pub
Thanks Bill. I checked for the extra length of cable, and it is not fitted to mine. (first registered Jan '91, so don't know when this 'engineering fix' was introduced).
Got to thinking about why I should only get one black spark plug. Figuring the things that would only affect one cylinder are either a plug lead or an injector. So pulled the lead off the affected plug, and low and behold, a lump of green corroded metal is still attached the the end of the plug. Not sure whether this can be fixed like yours, as this should live half way down a 5 inch long rubber tube which seems to be moulded onto the lead.
(Edit - also just noticed the ceramic part of the plug is cracked)
Got to thinking about why I should only get one black spark plug. Figuring the things that would only affect one cylinder are either a plug lead or an injector. So pulled the lead off the affected plug, and low and behold, a lump of green corroded metal is still attached the the end of the plug. Not sure whether this can be fixed like yours, as this should live half way down a 5 inch long rubber tube which seems to be moulded onto the lead.
(Edit - also just noticed the ceramic part of the plug is cracked)
Schadenfreude - the German's haven't got a word for that.
-
Billwill
- E30 Zone Regular

- Posts: 363
- Joined: Sun Jun 26, 2011 11:00 pm
- Location: South Africa
greg124 wrote:Thanks Bill. I checked for the extra length of cable, and it is not fitted to mine. (first registered Jan '91, so don't know when this 'engineering fix' was introduced).
Got to thinking about why I should only get one black spark plug. Figuring the things that would only affect one cylinder are either a plug lead or an injector. So pulled the lead off the affected plug, and low and behold, a lump of green corroded metal is still attached the the end of the plug. Not sure whether this can be fixed like yours, as this should live half way down a 5 inch long rubber tube which seems to be moulded onto the lead.
(Edit - also just noticed the ceramic part of the plug is cracked)
Great! I think you have just found your problem!
Best to change your plugs and your plug leads.
-
greg124
- E30 Zone Regular

- Posts: 668
- Joined: Tue Apr 03, 2007 11:00 pm
- Location: In the pub
Think that would be prudent, Bill.
Will order new leads on Monday, and change the cracked plug.
...and report back whether or not it's cured
Will order new leads on Monday, and change the cracked plug.
...and report back whether or not it's cured
Schadenfreude - the German's haven't got a word for that.
-
greg124
- E30 Zone Regular

- Posts: 668
- Joined: Tue Apr 03, 2007 11:00 pm
- Location: In the pub
New HT leads fitted (OEM) on Wednesday. Now done a few local runs and a 140-ish mile round trip today.
The car now runs perfectly.
Thanks to everyone for advice
The car now runs perfectly.
Thanks to everyone for advice
Schadenfreude - the German's haven't got a word for that.
