Ok guys, thinking caps time. im a bit stumped on this one myself.
The m20 has been running a bit rough recently, its fine above 1500 rpm but below that its shakey and almost sounds like its missing slightly.
Now i initially thought it was the blue temp sensor making it run rich due to a fuel smell at idle, having replaced the blue temp sensor and traced the fuel smell to perishing lines in the engine bay (already replaced) it seems it cant be that.
Also cleaned and tested the air temp sensor and the maf tracks just to be sure, hasnt made any difference.
Now its a bit odd, as it seems to have made the oil a bit petrol-ey over the last few months.
but the plugs are clean and white with no carbon deposits anywhere but around the edge of the thread.
It also dosent seem to be using any more oil than normal either (apart from what leaks out of the sieve that is the m20 rocker cover/plastic plugs)
It also returns a nice 28mpg ish around town and 30+ on a run, and pulls like a train.
So im strongly doubting its a compression issue.
Im a bit stumped as it seems to be a misfire or rich idle but it gives no symptoms of either when you do a plug chop, infact it almost seems a little lean going by the colour of the plugs.
although the nose on the plugs did seem a little long and im wondering if the parts monkey gave me hotter plugs than normal.
rough running
Moderator: martauto
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
-
e30topless
- E30 Zone Team Member

- Posts: 13595
- Joined: Wed Aug 23, 2006 11:00 pm
- Location: surrounded by scrap
overfuelling /borewashed ?HairyScreech wrote:Now its a bit odd, as it seems to have made the oil a bit petrol-ey over the last few months.
but the plugs are clean and white with no carbon deposits anywhere but around the edge of the thread.
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
thats what i thought at first, but the plug chop shows clean as it always is.
and the plugs were dry, dusty and a touch yellow brown, which would make me think towards a lean condition if anything.
but as i say i have no guarantee that i havent been given the wrong bosche plugs with to high a heat range as i dont have anything to check against up here.
im thinking towards some sort of low speed missfire thats cleaning up under load, thus producing no sooty plugs/chambers.
and the plugs were dry, dusty and a touch yellow brown, which would make me think towards a lean condition if anything.
but as i say i have no guarantee that i havent been given the wrong bosche plugs with to high a heat range as i dont have anything to check against up here.
im thinking towards some sort of low speed missfire thats cleaning up under load, thus producing no sooty plugs/chambers.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
-
e30topless
- E30 Zone Team Member

- Posts: 13595
- Joined: Wed Aug 23, 2006 11:00 pm
- Location: surrounded by scrap
I find bosch not too good, they can cause a rough idle... can't beat NGK BPR6ES 
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
my normal weapon of choice, standard heat range, cheap and easy to get hold of.
think pretty much everything i have had uses bprs6es plugs, the mini, the ka (both kinds) the bmw, the renault, etc....
might have to see if i have a full set of 6 lying about, if so ill donate these to the ka.
think pretty much everything i have had uses bprs6es plugs, the mini, the ka (both kinds) the bmw, the renault, etc....
might have to see if i have a full set of 6 lying about, if so ill donate these to the ka.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
Perhaps an Italian tune-up is called for? 
Youth is wasted on the young.
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
an Italian tune up is always called for, but in this case i dont think further flogging of the beast will help, iv got a nice welsh hill to climb flat in second on the way in in the morning, so the one thing its not is coked up.
something i saw mentioned on here was the engine earth with reference to over fueling/rough running and with the alternator fault perhaps the two are connected?
(or not in the case of a bad earth, budum tsh.)
something i saw mentioned on here was the engine earth with reference to over fueling/rough running and with the alternator fault perhaps the two are connected?
(or not in the case of a bad earth, budum tsh.)
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
-
sheebie
- E30 Zone Regular

- Posts: 773
- Joined: Sun Sep 07, 2008 11:00 pm
- Location: On level 3 obs
Mine is doing the same thing.
Been looking around, some suggest looking at the plug under the inlet manifold (c192) as they corrode because water collects there. I will be checking mine tomorrow.
I also suspect my injectors, but will check the plug first before sending the injectors for cleaning
Been looking around, some suggest looking at the plug under the inlet manifold (c192) as they corrode because water collects there. I will be checking mine tomorrow.
I also suspect my injectors, but will check the plug first before sending the injectors for cleaning
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
yep, thats on the list now.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
Now sorted, i was around 2500ppm HC at idle dropping like a stone to 216ppm HC at 2000 rpm, we decided it was an air leak and went looking, seems we have found an air leak from number 1 inlet runner, its cracked the gasket by the fuel injector.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
