Got in the car this morning, turned the key, and she fired up instantly.
Drove 100yards to the end of the road, engine stalled at idle and now won't start. She cranks over but there's no attempt to fire.
I removed a spark plug and rested it on the rocker cover and cranked the engine; no spark.
I confirmed that the coil is receiving 12V with ignition on, and that the HT lead from the coil to the distributor has a resistance of 2k Ohms. The CPS at its plug has a reading of 540 Ohms.
Update: I removed the HT lead from the coil and connected a spark plug to it. A quick crank caused a spark, so I'm guessing it's the distributor cap or rotor, but has anyone got any other ideas?
1988 320i not starting - no spark (edit: broken belt)
Moderator: martauto
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
Last edited by Grrrmachine on Tue Oct 25, 2011 3:21 pm, edited 1 time in total.
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
If you're absolutely sure you get a spark from the coil, but not from a plug then the distributor is likely to be the problem. Possibly the carbon centre contact broken up?
The other possibility, you're not going to like - a broken cambelt!
The other possibility, you're not going to like - a broken cambelt!
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
Thanks for filling me with confidence, Brian 
I got my allen keys and the 8mm spanner out and took off the distributor cap and rotor arm. Rotor face was worn smooth, and the contacts on the dizzy were pitted, like MIG welding with no gas!
Time for a proper service, methinks.
I got my allen keys and the 8mm spanner out and took off the distributor cap and rotor arm. Rotor face was worn smooth, and the contacts on the dizzy were pitted, like MIG welding with no gas!
Time for a proper service, methinks.
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
Oh dear...
Fitted a new cap and rotor, cranked the engine, still no spark at the plugs. Checked the fuel pump, checked the DME, and then stuck my hand down behind the alternator and found I could spin the timing belt tensioner freely. The belt's definitely gone.
Engine is a 1988 M20B20. Am I likely to have done any damage by losing the timing belt, especially since I've cranked the engine over repeatedly since then?
Fitted a new cap and rotor, cranked the engine, still no spark at the plugs. Checked the fuel pump, checked the DME, and then stuck my hand down behind the alternator and found I could spin the timing belt tensioner freely. The belt's definitely gone.
Engine is a 1988 M20B20. Am I likely to have done any damage by losing the timing belt, especially since I've cranked the engine over repeatedly since then?
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
Speedtouch
- Old Skooler

- Posts: 14130
- Joined: Tue Feb 14, 2006 11:00 pm
- Location: Canterbury
Only way to find out for sure is to do a compression test, but to do that you'll need to crank the engine over some more!
Best just to fit a new belt and see what happens...
Best just to fit a new belt and see what happens...
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
That's not a bad idea. I wanted to do a 2.5 transplant, but not just yet since winter's kicking in. I don't want to be wiggling in a new gearbox in minus 20 degrees...
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
Andyboy
- Alpina Colada
- Posts: 12577
- Joined: Mon Sep 11, 2006 11:00 pm
- Location: Notts
You will have bent at least three valves - sorry, but a belt breakage does this. Still, it's not a massive or expensive repair - new valves and I would strongly advise new rockers on the bent valves. A 1988 cars will likely still have the dreaded 17mm head bolts which need replacing with torx ones anyway.
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
Is there any way to confirm bent valves just by taking the rocker cover off? I know it's optimistic...
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
Speedtouch
- Old Skooler

- Posts: 14130
- Joined: Tue Feb 14, 2006 11:00 pm
- Location: Canterbury
You could slowly turn the engine over by hand (using a spanner on the end of the crank pulley) with the spark plugs out and listen for any piston-valve contact, and feel for any resistance.
If you feel any, don't try to force it, just get the head off and repair the damage.
If you feel any, don't try to force it, just get the head off and repair the damage.
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
I'm not quite in the mood to dismantle all the accessories yet to get the timing cover off, and I can't hear anything over the noise of the squeaking rubber, but the engine does turn all the way without any noticeable change in force.
I'll get a compression tester and take it from there.
I'll get a compression tester and take it from there.
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
