More M20 2.5 Questions - Part Identifier

Need technical Q/A then you're in the right place

Moderator: martauto

tom325sport
E30 Zone Regular
E30 Zone Regular
Posts: 819
Joined: Tue Jan 11, 2005 11:00 pm
Location: Guernsey

Post Wed Oct 19, 2011 7:45 pm

Can anyone please identify what this is? I think it is the carbon cannister but I've never seen one. It is in my late 318i Cab.

Image

However on a facelift engine I bought (2.5) the part number here are the same and is blocked on both ends.

Image

Can I remove the canister for good and what pipes need to stay and which can go?


Also i'm having troubled with the fuel side of things in regards to what goes where - Fuel IN and Fuel OUT? The 2 lines you can see were from the 318i engine. Do these need to be replaced?

Image

Or do they come from here...

Image

and here... which way round?

Image
Andyboy
Alpina Colada
Posts: 12577
Joined: Mon Sep 11, 2006 11:00 pm
Location: Notts

Post Wed Oct 19, 2011 10:27 pm

Yes, that's the carbon cannister. The valve thingy that plugs into it is the tank breather valve. No reason why you can't retain it tbh - it there and it works.
tom325sport
E30 Zone Regular
E30 Zone Regular
Posts: 819
Joined: Tue Jan 11, 2005 11:00 pm
Location: Guernsey

Post Thu Oct 20, 2011 11:30 am

OK thanks, what about the fuel lines anyone?
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Thu Oct 20, 2011 11:36 am

In your last piccie is the fuel pressure regulator,the fuel return goes here.Feed goes to the other connector on the fuel rail,possibly at the back end,possibly underneath the FPR.

How do you tell them apart?

If the engine does not run,swap 'em over.... :D
Youth is wasted on the young.
tom325sport
E30 Zone Regular
E30 Zone Regular
Posts: 819
Joined: Tue Jan 11, 2005 11:00 pm
Location: Guernsey

Post Thu Oct 20, 2011 11:50 am

Thanks Malc again!! I'm just sorting the odds and sods before I put the new engine in!

My 3rd picture down shows 2 pipes from the 1.8... do i need these or shall I swop them as they look a little on the small size to reach the new engine?
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Thu Oct 20, 2011 12:46 pm

tom325sport wrote:Thanks Malc again!! I'm just sorting the odds and sods before I put the new engine in!

My 3rd picture down shows 2 pipes from the 1.8... do i need these or shall I swop them as they look a little on the small size to reach the new engine?
Re-enforced fuel pipe is sold by the metre in most motor factors,so if they will not reach,or look suspect,buy in a couple of metres.Different internal diameters are available,though,so slice a small section(half an inch is ample)as a sample to take with you.

Please remember,no question is daft,if you do not know the answer... :D
Youth is wasted on the young.
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Thu Oct 20, 2011 1:15 pm

Fuel feed pipe is the one that has the filter in it, or the one that fuel comes out of if you crank the engine.
tom325sport
E30 Zone Regular
E30 Zone Regular
Posts: 819
Joined: Tue Jan 11, 2005 11:00 pm
Location: Guernsey

Post Thu Oct 20, 2011 5:21 pm

OK thanks again!

So just to confirm - FPR is fuel return and goes to one of those pipes in picture 3.
At the end of the injector rail is fuel feed (picture 4) and also goes to one of those pipes in picture 3.

Hopefully that's correct.
B7
E30 Zone Team Member
E30 Zone Team Member
Posts: 15841
Joined: Tue Feb 13, 2007 11:00 pm
Location: Surrey / West Sussex

Post Thu Oct 20, 2011 7:47 pm

Yes, You just need to check back at the rear for the filter and trace that one to the engine bay. That one goes on the fuel rail, The other to the FPR.
B7's Motto. "If it's French, BURN IT!!!!!!"
tom325sport
E30 Zone Regular
E30 Zone Regular
Posts: 819
Joined: Tue Jan 11, 2005 11:00 pm
Location: Guernsey

Post Thu Oct 20, 2011 8:14 pm

Great stuff!! I might just be able to do this!

One more thing... :o:

The red arrow here (sorry I've used someone's picture - Hope this is OK) is pointing to what I believe is the speed and cylinder ID sensors that come off the main engine loom.
The two plugs look like they go in to the bracket below the diagnostic plug.

Image

My question is - where do they go? I don't have anything else (I don't think I do) to plug them into. Am I missing some wiring?

Thank you again!!!
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Thu Oct 20, 2011 11:19 pm

One connects to the crank position sensor, which is mounted on the lower right front of the engine block, on a tab that holds it just clear of the big toothed pulley at the front of the crankshaft. The lead goes around the front of the engine, between the water pump pulley and the block, and must be secured properly, or the pulley will eat it,
The other one connects to a sensor that should be fitted around #6 spark plug lead.
tom325sport
E30 Zone Regular
E30 Zone Regular
Posts: 819
Joined: Tue Jan 11, 2005 11:00 pm
Location: Guernsey

Post Fri Oct 21, 2011 7:35 pm

OK thanks for helping to identify the crank position sensor and the sensor that is fitted around number 6 spark plug. I've been to see a friend of mine who has loads of parts and he gave me a box of stuff to search through!

Here are just a few of the crank position sensors of all different lengths (maybe from different BMW's) but the connections at both ends seem the same. Can I use any of these as I can't really make out the part numbers?

Image

Here is a picture of some spare leads he had in the connector (As mine on the engine hasn't got this lead). The sensor here though is on the end near the distributor end. How do you get this off and do you think it is the correct one?

Image
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Sat Oct 22, 2011 1:52 am

Last piccie....

You will need to trace the H/T lead with the polo ring back to the plug cap,then see if it will un-screw from the lead...

I have only replaced that sensor when fitting a new set of leads,they came complete with the sensor!

This sensor is just a crude(read early)form of cam sensor,it tells the ECU which three injectors to squirt fuel....the engine will run perfectly without it,but will use more fuel.
Youth is wasted on the young.
tom325sport
E30 Zone Regular
E30 Zone Regular
Posts: 819
Joined: Tue Jan 11, 2005 11:00 pm
Location: Guernsey

Post Sat Oct 22, 2011 5:41 pm

OK thanks Malc again! What about the crank position sensor? You think I can use any of them as they look very similar?