Project Trailer/BBQ

General E30 related discussions -
Please put technical questions in E30 Tech Help forum below

Moderator: martauto

Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Thu Oct 20, 2011 8:12 pm

Today, while I have nothing on, I thought I would start work on the convertible... Well, the new bbq/trailer. :twisted:


Managed to get it chopped up and thats it so far, but its all now sat in my unit :cool:


Threw back on all the rear suspension etc so its back on wheels.

I'll get some more pictures tomorrow off it chopped in half. Tomorrow I need to look at it a little more detailed rather than the quick chop I did today. Need to somehow figure out how I can have a heated boot (bbq) with lights still in and working... I was thinking off having the whole thing on a 'swing arm' type of thing so the bbq it self lifts out and sits on the lips of the boot seal. But it would be much cooler if it was still in the boot itself.

As for the front section, also need to figure out how I can make this look presentable and one whole piece, this will be storage space for when I camp away at shows etc.

Gonna need a few bits for it too so hoping any local zoners that egged me into doing it will throw me some spares for free if I need them as I have no budget for anything at the moment :o: :cry: Being self employed isnt the best all year round.

Image


Only got the 1 picture but will add some more tomorrow.


Only thing thats gonna be crap about it is facelift and i'll be dragging it around with my chromie. :( I would have prefered it to be a matching chromie rear end.

Any thoughts or suggestions would be helpful as i'm gonna be going at this blind. :roll:
Last edited by Jim320i on Fri Oct 21, 2011 7:05 pm, edited 1 time in total.
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Thu Oct 20, 2011 8:20 pm

Wouldnt look right. :( The lights wouldnt match and nor would the underneath section. I'll do it diamond schwarz to match my car but it will be facelift... Regardless, it should still be cool :cool:
Barx325i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6493
Joined: Wed Jul 26, 2006 11:00 pm

Post Thu Oct 20, 2011 8:23 pm

watch out for

- red hot fragments of metal that'll happily embed themselves in your cornea (even an hour infront of the bathroom mirror with a pin won't get them out!)

- razor sharp edges EVERYWHERE!

fun times 8)
User avatar
gnarkillius
E30 Zone Newbie
E30 Zone Newbie
Posts: 234
Joined: Sun Dec 09, 2007 11:00 pm
Location: Pompey/Manchester

Post Thu Oct 20, 2011 9:58 pm

I rock out a full face mask when cutting. Just a clear perspex cheapy not a welder mask or anything.

Those sparks go everywhere! Anyone who has cut metal has felt the sting of a white hot shard go down the neck of your tshirt. Down the front AND the back!

Ive had them go behind my watch strap, up my sleeve, into my boots. Quite amazing really when you try and figure out the trajectory it must have taken when one goes down the back of your neck!

Are you wearing no glasses even?
Kedge
Old Skooler
Old Skooler
Posts: 7698
Joined: Thu Jan 13, 2005 11:00 pm
Location: Leicestershire

Post Thu Oct 20, 2011 10:03 pm

Jim you bender, get some goggles on!!

Not sure how you'll stop the rear lights melting, I melted one on a breaker that was 15ft from a bonfire! 8O
Image
'86 Polaris 316 M20B28 Rebuild
Instagram - Kedge85
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Thu Oct 20, 2011 10:04 pm

Nope, chopped the whole thing without glasses... Front section was chopped down the middle and the front engine bay was chopped off too. :mad: I got hit a few times, eyes are a bit sore now though :cry: But i'll be fine... Its the only way I know how :mad:
User avatar
gnarkillius
E30 Zone Newbie
E30 Zone Newbie
Posts: 234
Joined: Sun Dec 09, 2007 11:00 pm
Location: Pompey/Manchester

Post Thu Oct 20, 2011 10:35 pm

Hardcore :cool:

Great idea btw. Cant offer advice on modding it to look chromie, only perhaps a chromie rear bumper with the fixings modded up, to fit? But Im sure you thought of that and its not possibe for some reason. Its gonna have the lower rear arches too ofc.

I reckon it still will look the business frankly. Seen similar done with minis, rear of a woody estate (thinking what that would be worth now even in poor condition :eek: ) used as a trailer.

Always thought it was an excellent solution. Please keep us updated!
J_A_C_K_Y_D
E30 Zone Newbie
E30 Zone Newbie
Posts: 164
Joined: Fri Sep 10, 2010 11:00 pm
Location: Cardiff

Post Fri Oct 21, 2011 12:22 am

Very cool, cant wait too see it

Loved the white one on e30 tech

good luck :D
B7
E30 Zone Team Member
E30 Zone Team Member
Posts: 15841
Joined: Tue Feb 13, 2007 11:00 pm
Location: Surrey / West Sussex

Post Fri Oct 21, 2011 6:54 am

TBH i'd go to B&Q and buy a BBQ.
B7's Motto. "If it's French, BURN IT!!!!!!"
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Fri Oct 21, 2011 10:04 am

B7 wrote:TBH i'd go to B&Q and buy a BBQ.

Thats where me and you differ Trev. :cool:


I was gonna weigh the whole car in... Seemed a shame as the shell was extremely tidy, no welds, no rot. So atleast half of it will keep rolling on :D

I've got a bbq I can take meets, and I have a trailer I can use too, so I dont actually need this... I just thought it would be a cool little project. Some people will see it as pointless, I see it as i've got no work on at the minute and getting very bored rattling around the house so thought I would take some time up...


I'll get some pictures later on today as it is in half, now, I do have a job on so need to leave and get started on it. Once i'm back, i'll pull it out the unit and take some snaps :cool:
Barx325i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6493
Joined: Wed Jul 26, 2006 11:00 pm

Post Fri Oct 21, 2011 10:33 am

B&Q will have some cracking deals with it being little late in the season, but hey, that's a great idea, so it's a case of opening the boot and sticking burgers on a grill instead of the weekly shop in?

It may smell a bit but that's as novel as they get! will it be gas or coal?
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Fri Oct 21, 2011 5:09 pm

Not descided on the gas or coal yet, gas may be alot easier but its something i'll figure out when I get to that point... My major problems I have got to figure out how to stop the lights and bumpers not to melt :mad:

The lights, I will hopefully be able to make detachable so that when its cooking I can remove... But then i'm left with the wiring leading up to them, so need to figure out how to heat proof them and the bumpers... Some sort of insulated casings within each other I think.

If I had the bbq on a pop out that raise out of the boot it would sort this problem, but I would prefer to be able to close the lid .

I then need to think about the heat that it will cause and what that will do to any paintwork, and then think about how hot the hole thing will actually get as the tyres wont do great in heat, nor will the plastic linings for the front section if I go down the load liner route :mad:


Lots of things I need to figure out yet but if it works it will be great... Only use it for meets and entertainment value, its not got to be amazing, just want it to work well.
Barx325i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6493
Joined: Wed Jul 26, 2006 11:00 pm

Post Fri Oct 21, 2011 5:33 pm

I'd make the lid quick release and the light clusters removable. I'd also be tempted to re-route the cabling underneath somehow - some exhaust heat wrap should do the trick if they stay routed a la oem - not sure the bumper will suffer but if it does, re-think it as that time comes

One major factor with the gas/coal choice is that the heat from gas is much more directional, whereas red hot coal embers radiate heat in every direction, which you don't want.. Plus coal is messy, over just a greasy drip tray with gas :)

thinking on, gas may not even melt the lights...

What about springs or are you going to drop some bricks in the wheel well?
Rav335uk
E30 Zone Meets/Events Team
E30 Zone Meets/Events Team
Posts: 27978
Joined: Wed Jan 19, 2005 11:00 pm
Location: Mad mad mad

Post Fri Oct 21, 2011 5:54 pm

Well done jim, this'll keep you busy.
BBQ wise, go for gas, as there is less radiant heat from it.
Image
If you Got "Haters",Then your doing something Right!
CR24v??? Where's it all gone?? LOL
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Fri Oct 21, 2011 7:02 pm

Well reading what you have both said, using gas would make it alot easier as the lights could remain in if I was able to heat proof it still. :D Running the wirings underneath would work well too so thats the most likely outcome.

The suspension, i'm unsure about? Would a normal suspension set up work on a trailer or would welded stiff bars be better? I'm thinking long distance drives so need it work well without bouncing around like mad :?

I popped over to my old man today aswell and he has some angled steel sitting in his yard which I am welcome to so thats an expense I havent got to pay for the underside/a frame section :cool:

Ricky is also heading over to his dads tomorrow to finally get the welder over here, thats his part of it as I havent got a clue about welding... I'll be giving it ago for sure though :twisted:

Gonna be on the scrounge for a few bits too if anyone is wanting to give stuff away to a worthy cause?

Need a bootlid, horseshoe, horseshoe rubber and wiring connectors for rear lights...

Can all be rusty and dented up and it can be full of filler :twisted:

Anyway...

Image

Image

Image

Image

Image

Image


winkeye winkeye winkeye winkeye winkeye
sweep
Married to the E30 Zone
Married to the E30 Zone
Posts: 10110
Joined: Sat Mar 15, 2008 11:00 pm
Location: spares & repairs in sheffield

Post Fri Oct 21, 2011 7:13 pm

Got a horse shoe here jim
B7
E30 Zone Team Member
E30 Zone Team Member
Posts: 15841
Joined: Tue Feb 13, 2007 11:00 pm
Location: Surrey / West Sussex

Post Fri Oct 21, 2011 7:18 pm

Thats gonna look lovely sat on your patio..........
B7's Motto. "If it's French, BURN IT!!!!!!"
User avatar
gooner1
Out humping Reindeer
Posts: 13280
Joined: Fri Apr 14, 2006 11:00 pm
Location: Northampton.For my sins.

Post Fri Oct 21, 2011 7:20 pm

Barx325i wrote:
It may smell a bit but that's as novel as they get! will it be gas or coal?
Better be Gas, Rav's cornered the market on Coal. winkeye

Jim, get some fecking Eye protection, seriously.
Last edited by gooner1 on Fri Oct 21, 2011 7:22 pm, edited 1 time in total.
Image
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Fri Oct 21, 2011 7:21 pm

@Sweep - Is that a freebie? winkeye

@B7 - I love your sarcasism... But as a smary reply, it will sit in the unit until I go to meets or have meets up mine, then when we do, it will be rolled out onto one of the many paddocks I have here, it's sole purpose for E30 meets... :moon:


Best thing is, I dont even cook :mad:
jimmyspeed
E30 Zone Regular
E30 Zone Regular
Posts: 848
Joined: Sat Sep 08, 2007 11:00 pm
Location: riding a wagon wheel west

Post Fri Oct 21, 2011 7:24 pm

Would a normal suspension set up work on a trailer or would welded stiff bars be better?

I have recently built a box trailer using an e30 rear beam with the diff and cv joints removed, i wanted to use the standard shocks but they were to long and would stick out the top and lose loading space, so luckily my old man had some old adjustable spas shocks which where a lot shorter and they fitted under the base nicely

i have used standard springs and they seem fine

The shocks only have about four inches of travel, there use being the dampening that you want cutting out the usual trailer jigging about

I have tested my trailer on a run down to weston super mare (beach race) and back, on the way i cruised at about 65 in the slow lane where i encountered the problem of the grooves run in to the road by truck tyres this caused it to weave a bit. I put this down to the wide tyres

to counter this problem i drove back at just above the speed limit winkeye in the middle lane - smooth as you like !!
sweep
Married to the E30 Zone
Married to the E30 Zone
Posts: 10110
Joined: Sat Mar 15, 2008 11:00 pm
Location: spares & repairs in sheffield

Post Fri Oct 21, 2011 7:40 pm

yes jim free
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Fri Oct 21, 2011 7:45 pm

Woo hoo :banana: Your a star mate.


Has Kedge been upto you yet? If not, can you pass it onto him if he dont mind and if he is still on his way over to you at some point as he is more local to me :cool:
Kedge
Old Skooler
Old Skooler
Posts: 7698
Joined: Thu Jan 13, 2005 11:00 pm
Location: Leicestershire

Post Fri Oct 21, 2011 8:34 pm

Too late Jim, I went up the other day!

You got a tow bar on the chromie for this?
Image
'86 Polaris 316 M20B28 Rebuild
Instagram - Kedge85
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Fri Oct 21, 2011 8:39 pm

Thats a shame :(

As for tow bar, not got one yet. Want to get a detachable one, which I assume they all are as its a add on... So will be on the search for one of them too, but need to be able to take it off when im not towing it else it will look well grandad 8O
Duke137
Married to the E30 Zone
Married to the E30 Zone
Posts: 7207
Joined: Sat Aug 29, 2009 11:00 pm

Post Fri Oct 21, 2011 8:47 pm

You can never hide a towbar completely tbh even the detachable type

I'm not sure about this project if I'm honest mate, though I admire your efforts.

Did you get my text about the Blaupunkt radio?
How do you pronounce 'either'? I say 'either', but some say 'either'. Either is correct.
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Fri Oct 21, 2011 8:55 pm

I'm still not sure about it to be honest but i'll see how it goes and how far it gets before I give up and get bored :mad: I'll try though.

Cant read any texts mate as I dropped my phone a few month back and too tight to buy another one :mad: The screen is smashed so all I can do is take calls... Phone bill has dropped loads. :twisted:

Pm me if you want mate 8)
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Sat Oct 22, 2011 1:35 am

Can you not line the area around the BBQ with asbestos,or better still,it's modern equivilant?
Youth is wasted on the young.
User avatar
gnarkillius
E30 Zone Newbie
E30 Zone Newbie
Posts: 234
Joined: Sun Dec 09, 2007 11:00 pm
Location: Pompey/Manchester

Post Sat Oct 22, 2011 2:22 am

diable wrote:
gnarkillius wrote:
Those sparks go everywhere! Anyone who has cut metal has felt the sting of a white hot shard go down the neck of your tshirt. Down the front AND the back!
Wait until you experience a just ejected 9mm casing going down the back of your shirt, fooking made me jump.
Well since you mention it, Ive been struck with a 5.56 nato :cry:

SA80 -> tree trunk -> Side of my head.

Ah good times
B7
E30 Zone Team Member
E30 Zone Team Member
Posts: 15841
Joined: Tue Feb 13, 2007 11:00 pm
Location: Surrey / West Sussex

Post Sat Oct 22, 2011 7:05 am

daimlerman wrote:Can you not line the area around the BBQ with asbestos,or better still,it's modern equivilant?
Or buy an oil drum.................
B7's Motto. "If it's French, BURN IT!!!!!!"
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Sat Oct 22, 2011 10:30 am

B7 wrote:
daimlerman wrote:Can you not line the area around the BBQ with asbestos,or better still,it's modern equivilant?
Or buy an oil drum.................
But that means spending money.... winkeye
Youth is wasted on the young.
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Sat Oct 22, 2011 10:37 am

B7 wrote:
daimlerman wrote:Can you not line the area around the BBQ with asbestos,or better still,it's modern equivilant?
Or buy an oil drum.................

I'm gonna start 'shoo'ing' you off soon... Thats me trying to be polite... :? Give up being a c0ck will you? I understand you don't like it but you havent got to throw in stupid comments every few posts, I already know your view... :roll:
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Sat Oct 22, 2011 10:40 am

Sorry,Jim,I was trying to be practical and helpfull.... :cry:
Youth is wasted on the young.