Wiring help pin 20

Need technical Q/A then you're in the right place

Moderator: martauto

tom325sport
E30 Zone Regular
E30 Zone Regular
Posts: 819
Joined: Tue Jan 11, 2005 11:00 pm
Location: Guernsey

Post Wed Oct 19, 2011 12:47 pm

Help needed guys. Just checking the wiring at pin 20 on the c101 plug and it is brown on the engine loom. Pin 20 on the body loom at c101 is red/yellow.

What shall I do? Engine is m20 2.5 facelift.
I've read Brian wiring help but can't find anything with brown wire on engine loom? Thanks.
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Wed Oct 19, 2011 2:00 pm

--------------------------------------------------------------------------------
Check whether there is any wire connected to pin 20 on the car loom side of the connector. If there is, it will either be red/yellow or brown.
If it is brown, cut it away from the pin, and make sure the free end can't come into contact with anything.
If it is red/yellow, then leave it alone - it's the power feed for the ABS system. You will then have to check pin 20 of the engine loom side of the connector, to see if it has a red/yellow as well. If it has, all well and good, but if there is no red/yellow fitted, you will have to add one, between the pin and the terminal of the DME relay that has a red/blue on it.

(copied from the engine wiring sticky in 'engine swaps'...original post on page two by Brian)
Youth is wasted on the young.
tom325sport
E30 Zone Regular
E30 Zone Regular
Posts: 819
Joined: Tue Jan 11, 2005 11:00 pm
Location: Guernsey

Post Wed Oct 19, 2011 2:09 pm

Thanks. I have checked this but I have a BROWN wire in the engine loom at pin 20, not red/yellow.
There is red/yellow on the body loom though. Can I plug this in or not?
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Wed Oct 19, 2011 2:11 pm

daimlerman wrote:--------------------------------------------------------------------------------
You will then have to check pin 20 of the engine loom side of the connector, to see if it has a red/yellow as well. If it has, all well and good, but if there is no red/yellow fitted, you will have to add one, between the pin and the terminal of the DME relay that has a red/blue on it.

(copied from the engine wiring sticky in 'engine swaps'...original post on page two by Brian)
All the infor for both side of C101 was there!
Youth is wasted on the young.
tom325sport
E30 Zone Regular
E30 Zone Regular
Posts: 819
Joined: Tue Jan 11, 2005 11:00 pm
Location: Guernsey

Post Wed Oct 19, 2011 3:52 pm

OK had another read but there explains nothing if I have a 'brown' wire at the c101 plug engine loom side. It says you either have 'red/yellow wire' or 'none'.

Quote from that post...


Check whether there is any wire connected to pin 20 on the car loom side of the connector. If there is, it will either be red/yellow or brown.
If it is brown, cut it away from the pin, and make sure the free end can't come into contact with anything.
If it is red/yellow, then leave it alone - it's the power feed for the ABS system. You will then have to check pin 20 of the engine loom side of the connector, to see if it has a red/yellow as well. If it has, all well and good, but if there is no red/yellow fitted, you will have to add one, between the pin and the terminal of the DME relay that has a red/blue on it.

Am I reading it wrong? If the wire (engine loom side) is anything but red/yellow then to add one? Thank you. :)
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Wed Oct 19, 2011 5:18 pm

As I read your posts,you have a red/yellow on the car side of C101 and a brown on the engine side?

As I understand Mr Moore's wiring warning in the Engine swaps section,that brown wire may well be an earth from the temp gauge sender,which is not used because the temp gauge sender is earth via the engine.

Now I also understand that the red/yellow on the car side goes to the ABS,the feed,I think...so unless you modify the engine side pin 20,you will have no feed to the ABS,so the ABS light will not go out,MoT fail....so you need to run a suitable wire from the DME relay terminal with a red/blue attached to pin 20,and dis-connect the brown wire.
Youth is wasted on the young.
tom325sport
E30 Zone Regular
E30 Zone Regular
Posts: 819
Joined: Tue Jan 11, 2005 11:00 pm
Location: Guernsey

Post Wed Oct 19, 2011 6:55 pm

daimlerman wrote:As I read your posts,you have a red/yellow on the car side of C101 and a brown on the engine side?
Yes that is correct.

Thank you for explaining it to me. Much appreciated!! :)
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Oct 19, 2011 7:10 pm

What year is your engine loom from?
tom325sport
E30 Zone Regular
E30 Zone Regular
Posts: 819
Joined: Tue Jan 11, 2005 11:00 pm
Location: Guernsey

Post Wed Oct 19, 2011 7:37 pm

When I bought the engine (facelift) the loom was all boxed up and off the engine. I think it all came from the same engine as I saw it advertised on here. I'm sure the car was a 1988.

Here is a picture of the engine loom c101 plug. Pin 20 shown with brown wire...

Image
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Oct 19, 2011 7:51 pm

Very strange - never seen one before.
The other end of it should be to one of the pins on the injector loom plug. The earth wire usually exists in the injector loom, but just ends at the socket to the engine loom.
As daimlerman has said, you will have to re route this wire to the DME relay pin with the red/purple. This will feed 12 volts + to the red/yellow on pin 20 of the body loom, when the ignition is switched on.
tom325sport
E30 Zone Regular
E30 Zone Regular
Posts: 819
Joined: Tue Jan 11, 2005 11:00 pm
Location: Guernsey

Post Wed Oct 19, 2011 7:55 pm

Super stuff!! Thank you for your help.