Tach-- No output

Need technical Q/A then you're in the right place

Moderator: martauto

E30_Crazy
E30 Zone Regular
E30 Zone Regular
Posts: 733
Joined: Fri Mar 05, 2010 11:00 pm
Location: Alaska, USA (Lived in Brandon, Suffolk)

Post Sun Oct 16, 2011 12:49 am

I've seen several of these threads in the past, but never looked into it before. I bet it's been answered, but I can't get the search to give me anything usefull. Anyways, he goes...

I've got a facelift engine and loom in a pre-facelift shell and body loom. Everything is good so far (no meltdown from the ground/abs wiring getting cross at the plug) except now that it's running, I've got no tach/mpg. The rest of the cluster works as before (never had the service lights before). I thought that the plug that comes out of the loom right by the ECU plug (white, three wires) was for the tach, and I tried to splice in the matching plug from my old loom to the new one, but no luck.

Anyways, if anyone has done this swap before, or is anyone knows off-hand what/where the tach wiring is at and how to convert to facelift, I'd appreciate the help!

Thanks,
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Sun Oct 16, 2011 9:37 am

You are in the right area,but as I have not needed to do this myself I cannot remember the detail.

Search for Mike Jermyn's engine building thread,or perhaps a tech help thread started by him for the detail.

Failing that,I think that 'Danthe' or 'Dezzy' may be able to help,try a PM.
Youth is wasted on the young.
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Oct 16, 2011 9:52 am

There's a small three pin plug hanging down behind the dash on the RH side that had a plug connected to it from the old engine loom. Your new engine loom feeds the signals that went through this connector via the 20 pin C101 engine loom plug, so you have the choice of either extending two wires from the hanging plug to the engine loom socket next to the fusebox (as they are in later body looms), or teasing the two wires out of the engine loom, near the ECU plug, cutting them (abandoning the rest of the wire to the C101 plug) and splicing the plug from your old engine loom onto the wires.
E30_Crazy
E30 Zone Regular
E30 Zone Regular
Posts: 733
Joined: Fri Mar 05, 2010 11:00 pm
Location: Alaska, USA (Lived in Brandon, Suffolk)

Post Sun Oct 16, 2011 4:14 pm

Brianmoooore wrote:and splicing the plug from your old engine loom onto the wires.
Sounds like what I already tried to do, just the wrong wires.

Will it be ok to just leave the the rest of the wire going to the C101 in with the rest of the loom after cutting, or do I need to heatshrink/cover it some way? Shouldn't be any signal, I wouldn't think... Could be wrong though.

I'll try looking around at the above mentioned threads/user and see if there is any more details on it, but Brian, do you know what color wires I need to fish out of the loom for this? I'll try looking for a pinout diagram for the ECU plug too.
E30_Crazy
E30 Zone Regular
E30 Zone Regular
Posts: 733
Joined: Fri Mar 05, 2010 11:00 pm
Location: Alaska, USA (Lived in Brandon, Suffolk)

Post Sun Oct 16, 2011 4:39 pm

Doing some reading, and wondering... Is the C104 the name for the ECU plug?
E30_Crazy
E30 Zone Regular
E30 Zone Regular
Posts: 733
Joined: Fri Mar 05, 2010 11:00 pm
Location: Alaska, USA (Lived in Brandon, Suffolk)

Post Sun Oct 16, 2011 7:42 pm

Ok, so from the ECU plug, pin 6 is the engine speed, and pin 32 is for the econometer. There are 3 wires, so what is the 3rd one for? I assume the three are power, ground, and signal? Still trying to find color codes for both looms so I know what wires to cut, and which colors from the pre-face plug splice into which colors of the facelift loom.
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Sun Oct 16, 2011 8:03 pm

Ignore the third wire, which is green/ignition live, to be sure you have the right wires check for continuity between them and the pins on the C101, Pin 8 (fuel rate) should be White/Black and Pin 9 (engine speed) should be Black
The wires on the small 3 pin plug can be different colours but usually one is light coloured, yellow or white etc and the other is dark, black or blue, the dark connect to Black Engine speed and the light connect to White/Black fuel rate
E30_Crazy
E30 Zone Regular
E30 Zone Regular
Posts: 733
Joined: Fri Mar 05, 2010 11:00 pm
Location: Alaska, USA (Lived in Brandon, Suffolk)

Post Sun Oct 16, 2011 8:16 pm

IIRC (car is parked near the MOT place currently) the colors of the plug I cut from the old loom are black green and white.

Pin 8 and pin 9 you mentioned, those are pin numbers of the C101? They should be the same color up by the ECU plug right? I can cut them there under the dash and check for continuity at C101 pins 8 and 9?

I always though that wiring and electrics in a car would be a cake-walk after doing it on jets, but it seems not!
E30_Crazy
E30 Zone Regular
E30 Zone Regular
Posts: 733
Joined: Fri Mar 05, 2010 11:00 pm
Location: Alaska, USA (Lived in Brandon, Suffolk)

Post Sun Oct 16, 2011 9:41 pm

Shoot, gonna be tricky getting the continuity between under the dash and in the engine bay. Only have one set of multimeter wires (no extra lengths). I'll see what I can do when I get over there tonight. All that stuff of mine is in the back seat.
E30_Crazy
E30 Zone Regular
E30 Zone Regular
Posts: 733
Joined: Fri Mar 05, 2010 11:00 pm
Location: Alaska, USA (Lived in Brandon, Suffolk)

Post Mon Oct 17, 2011 12:47 am

Ok, got them all wired in. Everything was where it was supposed to be. Maybe I just got used to not having a tach, but it almost seems that it reads a little high. At idle is fine, but then when lightly accelerating from stopped, it reaches 4k rather quick. If I had wired them backwards (tach to econo) would they even work? I only checked that the tach was working at idle, and wrapped them up before giving it any revs :-x . Econo seems to be fine though. Do they receive the same signal, and the dials give their own respective readings?
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Mon Oct 17, 2011 8:37 am

Have you changed the number of engine cylinders? Sounds like a six pot engine driving a four pot tacho.
Coding chip on the lower right of the front face of the cluster (behind trim panel) needs changing.
E30_Crazy
E30 Zone Regular
E30 Zone Regular
Posts: 733
Joined: Fri Mar 05, 2010 11:00 pm
Location: Alaska, USA (Lived in Brandon, Suffolk)

Post Mon Oct 17, 2011 5:52 pm

Nah, it was a 6 pot to 6 pot swap. Maybe I'm just imagining things. It does have it's redline raised to 8k though. And it could just be that it sounds different than the last engine, so it's playing tricks with my ear (being used to certain tones at RPM's and normal shifting speeds)