Not having a good day - timing belt change

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
James90
E30 Zone Regular
E30 Zone Regular
Posts: 271
Joined: Thu Sep 23, 2010 11:00 pm
Location: Nottingham

Post Sat Oct 15, 2011 7:58 pm

Went to attempt the cambelt swap on my 325i today..

It took me about an hour to get the fan off - someone must have put it on wayyy to tight at some point.

Turns out the water pump I have bought is not the right one - it has 2 ends to connect a hose to - the one I have taken out only has 1 - I didn't know there was more than 1 style of water pump.

I took the thermostat outlet off no problem - thermostat would not come out for love nor money so I thought I must have to take the whole housing off - took me about an hour to do this too - bloody thing snapped so i need another one now (see my thread in the wanted section lol)
but even worse one of the studs snapped off in the head (see pic below) can i get it out without taking the head off and taking it somewhere?

Image

Uploaded with ImageShack.us


Cheers
'88 325i Auto Chromie Cabriolet in Alpine White
asmith88
E30 Zone Addict
E30 Zone Addict
Posts: 2684
Joined: Sat Aug 23, 2008 11:00 pm
Location: Co Down, N.I

Post Sat Oct 15, 2011 8:24 pm

oh dear that looks pretty flush, access cant be great either, worth trying a good stud extractor before taking the head off
1990 brilliant red 318 is
User avatar
James90
E30 Zone Regular
E30 Zone Regular
Posts: 271
Joined: Thu Sep 23, 2010 11:00 pm
Location: Nottingham

Post Sat Oct 15, 2011 8:39 pm

it is pretty much flush :(
I don't have any stud extractors but don't mind buying some - how do they work?
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Sat Oct 15, 2011 8:51 pm

Only way to get that out is to drill into the stud and use one of those extractors with a left hand thread,the theory is that the tighter you get the extractor,the better the chance of removing the stud.

In your favour,there is room on the inlet side of the engine to get at the thing!
Youth is wasted on the young.
E30BeemerLad
Married to the E30 Zone
Married to the E30 Zone
Posts: 16806
Joined: Mon Mar 28, 2005 11:00 pm
Location: Norfolk

Post Sat Oct 15, 2011 9:29 pm

Ideally you need a better set than this, but you probably won't do any better on a Sunday morning

http://www.screwfix.com/p/stud-extracto ... tid=130983

Make sure you drill a decent pilot hole so the reverse screw can grip well otherwise they are a bit cack if they don't grip.

Here's what to do

[youtube][/youtube]
User avatar
James90
E30 Zone Regular
E30 Zone Regular
Posts: 271
Joined: Thu Sep 23, 2010 11:00 pm
Location: Nottingham

Post Sun Oct 16, 2011 12:51 am

thanks for the advice fellas! The guy on that vid made it look so so easy!
I'm not in a rush to get it done tomorrow (need to source another water pump and thermostat housing now) so will get a better set of thread extractors - any suggestions?

cheers
'88 325i Auto Chromie Cabriolet in Alpine White
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Oct 16, 2011 9:56 am

See if you can find a similar vid., showing how to remove broken stud extractors from drilled holes.
Barx325i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6493
Joined: Wed Jul 26, 2006 11:00 pm

Post Sun Oct 16, 2011 10:27 am

when the extractor bit is in there really be careful not to go mad, they're a bit brittle - or at least the cheap set I was using was - the smallest 2 snapped off inside the pilot holes - that was annoying

spray WD40 on there to keep it soaked - you want a reservoir of WD if it's at all possible, also with the pilot hole, start small and go progressively bigger, you want to disturb the contact between the stud and the surrounding alloy as much poss so heating the stud by drilling and letting it cool will help, also tap it a bit with a punch and put something appropriate in the pilot hole and wiggle, tap etc

as you tap and wiggle it will hopefully loosen the corroded alloy around the stud, also with the temperature changes, WD it will travel along the thread in a capillary action, heat & WD FTW

alloy cools quicker than the steel stud, so I'd try removing it as it's cooling down not when it's too cold, if you're still having no joy, put a drill bit in the freezer and insert the solid end into the pilot hole immediately before the extractor

pain in the bum
Andyboy
Alpina Colada
Posts: 12577
Joined: Mon Sep 11, 2006 11:00 pm
Location: Notts

Post Sun Oct 16, 2011 2:00 pm

James90 wrote: Turns out the water pump I have bought is not the right one - it has 2 ends to connect a hose to - the one I have taken out only has 1 - I didn't know there was more than 1 style of water pump.
Sounds like it might be an E21 pump.
User avatar
James90
E30 Zone Regular
E30 Zone Regular
Posts: 271
Joined: Thu Sep 23, 2010 11:00 pm
Location: Nottingham

Post Sun Oct 16, 2011 2:01 pm

thanks for all your replies - you've talked me into having a go at getting it out in situ myself. I'm gonna buy a few cobalt drill bits - so you reckon don't use the drilling spray cos i want it to get hot and cool down etc?
will prob have a go next weekend now - will nip out and spray some WD on it every night.
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Sun Oct 16, 2011 2:08 pm

Speaking from personal experience with this sort of thing,and I am not earning a living as a mechanic,your problem will be getting a drill started reasonably central in the stud.If you can centre punch the end of the stud to give the drill something to grip,you will do better.I would start with a very small drill,and work my way up to the largest size that will go in without damaging the thread,then try an extractor,if the stud has not given up and un-screwed it's self.

Good luck!
Youth is wasted on the young.
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Oct 16, 2011 2:17 pm

There is a point of view that says you should deliberately drill the pilot hole off centre. Increase the size of the drill until you just cut into the threads at the narrowest point and the remains will collapse inwards, whereupon you can tease them out with a small screwdriver.
The thread in the head will be damaged at one point around its circumference, but shouldn't be enough to cause problems.
User avatar
James90
E30 Zone Regular
E30 Zone Regular
Posts: 271
Joined: Thu Sep 23, 2010 11:00 pm
Location: Nottingham

Post Sun Oct 16, 2011 11:21 pm

daimlerman wrote:Speaking from personal experience with this sort of thing,and I am not earning a living as a mechanic,your problem will be getting a drill started reasonably central in the stud.If you can centre punch the end of the stud to give the drill something to grip,you will do better.I would start with a very small drill,and work my way up to the largest size that will go in without damaging the thread,then try an extractor,if the stud has not given up and un-screwed it's self.

Good luck!
A mechanic friend of mine (who won't touch it unless I take the head off - which obviously I'd rather avoid) suggested using a dremel with a conical bit (pushing forwards to make the face of the stud concave) to start it off then going in with a drill bit after.

Brianmoooore wrote:There is a point of view that says you should deliberately drill the pilot hole off centre. Increase the size of the drill until you just cut into the threads at the narrowest point and the remains will collapse inwards, whereupon you can tease them out with a small screwdriver.
The thread in the head will be damaged at one point around its circumference, but shouldn't be enough to cause problems.
Interesting. So many different ways!!



I've ordered an extractor set and 3mm and 3.5mm cobalt drill bits. I haven't measured what size the stud is but if I can get away with doing a 4mm hole then I'll get a 4mm bit too.
leeparkes
Married to the E30 Zone
Married to the E30 Zone
Posts: 9535
Joined: Thu Jan 03, 2008 11:00 pm
Location: Black country

Post Sun Oct 16, 2011 11:36 pm

Brianmoooore wrote:There is a point of view that says you should deliberately drill the pilot hole off centre. Increase the size of the drill until you just cut into the threads at the narrowest point and the remains will collapse inwards, whereupon you can tease them out with a small screwdriver.
The thread in the head will be damaged at one point around its circumference, but shouldn't be enough to cause problems.
This has worked for me.

Id never use easy outs again unless there the thick ones.
Cypriotgeeza wrote:I done both my mates in my old 318is
felt so proud,even tried it with a E30 325i and got put in my place.. :o:
Barx325i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6493
Joined: Wed Jul 26, 2006 11:00 pm

Post Mon Oct 17, 2011 12:08 am

not keen onthe idea of the eccentric pilot, but it will get the wd right into the thread

not quite the same, but here's some recent handy work on iS manifold nuts that were round when I offered the 13mm up to them

Image

Image

I do like challenges like this :)
User avatar
James90
E30 Zone Regular
E30 Zone Regular
Posts: 271
Joined: Thu Sep 23, 2010 11:00 pm
Location: Nottingham

Post Mon Oct 17, 2011 12:22 am

Barx325i wrote: I do like challenges like this :)
Fancy a trip to Nottingham then? :P
User avatar
James90
E30 Zone Regular
E30 Zone Regular
Posts: 271
Joined: Thu Sep 23, 2010 11:00 pm
Location: Nottingham

Post Sun Oct 30, 2011 3:54 pm

Got round to doing this today.
Guess what... The easy out snapped off. Bet the easy out won't be very easy to get out. This car hates me!
User avatar
Billwill
E30 Zone Regular
E30 Zone Regular
Posts: 363
Joined: Sun Jun 26, 2011 11:00 pm
Location: South Africa

Post Sun Oct 30, 2011 5:53 pm

James90 wrote:Got round to doing this today.
Guess what... The easy out snapped off. Bet the easy out won't be very easy to get out. This car hates me!
Yeah...as Brian warned :D
If you have space off to the side of the broken easy-out...try drill a small hole to just touch on the thread as Brian advised and hopefully with a bit of Q20 sprayed inside you may be able to tease the bolt out. Or else drill a series of very small holes around the easy-out to try release it.
I have been in this position before...fortunately many years ago when I was still young :D
User avatar
James90
E30 Zone Regular
E30 Zone Regular
Posts: 271
Joined: Thu Sep 23, 2010 11:00 pm
Location: Nottingham

Post Sun Oct 30, 2011 6:01 pm

Yup!
I have a little bit of space at 1 edge of it which I have started to drill another small hole but gave up after about 10 minutes cos I was aching and the drill bit was snapped so wasn't making much progress. Have just ordered some more drill bits will crack on with it next weekend.
I will get there without taking the head off!!
'88 325i Auto Chromie Cabriolet in Alpine White
User avatar
James90
E30 Zone Regular
E30 Zone Regular
Posts: 271
Joined: Thu Sep 23, 2010 11:00 pm
Location: Nottingham

Post Sun Nov 06, 2011 9:48 pm

Well those cobalt drill bits were chocolate fireguards.
Dremel was the winner the was cutting through the stud extractor like butter! (well not quite but it was in comparison to the drill bits)

anyway - about 3 hours work today :
Image

Uploaded with ImageShack.us

And slide the Thermostat Housing on to test:
Image

Uploaded with ImageShack.us


(Borat voice) Great Success!
'88 325i Auto Chromie Cabriolet in Alpine White
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Mon Nov 07, 2011 12:40 am

Well done!
Youth is wasted on the young.
HairyScreech
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6265
Joined: Sun Jan 21, 2007 11:00 pm

Post Mon Nov 07, 2011 12:46 am

why did you take the thermostat off to do the cam belt?
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822

m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
User avatar
James90
E30 Zone Regular
E30 Zone Regular
Posts: 271
Joined: Thu Sep 23, 2010 11:00 pm
Location: Nottingham

Post Mon Nov 07, 2011 7:38 am

Because I wanted to change the thermostat and it was stuck in there solid - and it was the first time i've attempted such a thing so wasn't even sure the stat was meant to come out by just taking the end of the thermostat housing off so thought I must have to take it off completely. I now wish I'd spent 3-4 weekends yanking at the thermostat instead!!
'88 325i Auto Chromie Cabriolet in Alpine White
HairyScreech
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6265
Joined: Sun Jan 21, 2007 11:00 pm

Post Mon Nov 07, 2011 7:10 pm

always the way, atleast now you know it wont be a problem if you need to do anything to it in future.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822

m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&