Replacing sunroof tray - What glue to use?

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Tue Oct 11, 2011 12:48 pm

Looking at my sunroof tray, the 2 rear drains are rusted from the inside. I was going to cut them out and weld in repair sections cut from the good tray in my other touring.

Looking at it earlier I noticed the whole tray is bonded to the roof skin and sunroof opening, there also look to be 4 brackets spot welded to the tray but that seems to be about it.

Has anyone removed/replace a complete tray before? If it's do able I see it as a better solution than welding in 2 new drains and another patch. I can fully treat the replacement panel and the whole roof while I have access to them both. Welding in new sections I have to clean and treat the welded area's which is going to be tricky as the rear ones are hard to reach.

Who has done it and how easy/hard was it to do?

This is pretty much the last rusty area on the car that I need to sort out, to much time/work has gone into the rest of the shell to backout or take the easy solution :D
Last edited by Jozi on Thu Oct 13, 2011 4:33 pm, edited 1 time in total.
Topblag
Old Skooler
Old Skooler
Posts: 7095
Joined: Wed Jul 30, 2008 11:00 pm
Location: Fife - You got a problem with that ?

Post Tue Oct 11, 2011 12:56 pm

I think you may be easier replacing the entire roof section. Which won't be easy AFAIK.
1990 325i Cab auto in Alpine White II
1988 Alpina C2.5 moredoor in Black, 71k
1990 325ix, moredoor auto in Laser Blue. 51k
1984 Hartge H35 in Black
2004 996 C4S in Silver 43k manual
2006 Audi S6 V10 in Black 58k
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Tue Oct 11, 2011 1:44 pm

Just onto the dealer there, complete roof skin isn't available. It would have been cheaper though than a sunroof tray, which is over 400 quid :mad:

I don't have the skills to replace a complete roof, it's a pretty big task, not that replacing a tray wont be :(

Here's the 2 brackets, are they welded onto the body or is the bracket on the body and welded to the sun roof tray?
Image
Image
You can see the rust in the 2nd pic, it's much worse on the other side :cry:
Morat
E30 Zone Team Member
E30 Zone Team Member
Posts: 8943
Joined: Thu Feb 09, 2006 11:00 pm
Location: The Peoples Republic of Yorkshire

Post Tue Oct 11, 2011 3:13 pm

I would say that compared with some - that is a minter!
E30 Touring 0.35 cD - more slippery than prison soap :)

Image
Praise the Lard... and pass the dripping!
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Tue Oct 11, 2011 3:14 pm

You should see the tray in the other car, not a bit of rust on it!

I just found this thread about removing the tray: http://www.r3vlimited.com/board/showthread.php?t=135991
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Tue Oct 11, 2011 3:24 pm

I'll get that written for the Wiki ASAP. With roof rot killing of a lot of cars, that info is diamond.
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Tue Oct 11, 2011 3:25 pm

Grrrmachine wrote:I'll get that written for the Wiki ASAP. With roof rot killing of a lot of cars, that info is diamond.
Do you want me to take any pics etc while I'm at it?
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Tue Oct 11, 2011 5:10 pm

I'd love you to. Let me know how it goes and you can email me the results, including anything you feel like writing down. Then I'll combine it with that article into a proper Wiki article.
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Tue Oct 11, 2011 5:21 pm

I got started with this on the project, just some spot welds drilled out, have to do it all again on the donor shell. I'll take some pics while I do it, between the 2 shells I should get enough pics for you and you can add how to fit the new one as well when I'm done.
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Thu Oct 13, 2011 4:32 pm

Anyone any suggestions for bonding the frame to the roof?

From what I gather the glue thats there might not be structural, panel is held in place with welded brackets, but more so to seal the frame to the roof.

I've had a look around and thought maybe panel bond would do or a windscreen bond of some sort. Maybe even tiger seal? I don't know how they stand up to high temps when the car is baking in the sun (or oven after paint), probably needs to stay semi flexible?
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Fri Oct 14, 2011 1:56 am

I have seen a photo sequence from another zoner,who's name eludes me at the moment,who had a roof skin swapped on a saloon,seems odd that touring roof skins are NLA...but he had to have the skin brazed on,so at a guess it is the surrounding structure that is structural,not the roof skin it's self.

In your instance,as you have a sound donor to cut from,it may well be easier to slice out what you need,be a swine to keep the roof skin flat,though!
Youth is wasted on the young.
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Fri Oct 14, 2011 9:35 am

Malc, I got the complete frame removed yesterday
Image

Compared to what's on the project car, it's clean with only a few bit's of surface rust to clean up. I'll be painting the frame and the underside of the roof before fitting it back it.

I'm not sure whats best to use to bond the frame back in.
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Fri Oct 14, 2011 10:25 am

I reckon you did well to get that out without distorting it!

Be worth a PM to one of the bodyshop guys on the zone for advice regarding the right sort of 'glue' to re-fit....bet the factory had the roof skin upside down,though.... winkeye
Youth is wasted on the young.
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Fri Oct 14, 2011 10:44 am

I might have distorted the roof on the donor a little, on of the spot welds wasn't drilled right :P

Getting the one of the project shell has been much handier so far, angle grinder cut it all out except where it's bonded.

I reckon in the factory they fitted the roof skin after they put the frame in, there's 4 welded brackets on top of a seam, under the roof skin. Or the bracket is spot welded on after.

Image
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Fri Oct 14, 2011 10:59 am

So in reality,the tray is spot-welded in,and the seam sealed in what we could describe as 'the usual way'?

The spot-welds are structural and the sealer should keep moisture out?
Youth is wasted on the young.
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Fri Oct 14, 2011 11:05 am

I think so. It's not fully sealed at the back though, and mine had cracked as well around there.