all
anyone recommend the right kit to go from with HIDs4U?
after doing a recent Ring and Spa trip and having to travel at night I suddenly realised how truly pants the e30 lights are compared to a modern HID lit car.
they do a couple of kits so just wondered if anyone has done this, experiences or recommendations?
thanks, Nick
HID upgrade
Moderator: martauto
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
4300K H1 kit is what you need. All are made in China, whatever the label claims, and reliability seems reasonable. I've come across three duff ballasts now, and curiously, they've all been on BMWs with Valeo alternators, rather than Bosch.
As well as the kits above, I also have a set in use using Chinese burners connected to ex. Range Rover ballasts.
OE E30 lights aren't that bad, provided they are adjusted correctly. The beam cut off is very sharp, so even slightly lower than they should be has a dramatic effect on their range.
Did you change them to RH dip for your ring/spa trip?
As well as the kits above, I also have a set in use using Chinese burners connected to ex. Range Rover ballasts.
OE E30 lights aren't that bad, provided they are adjusted correctly. The beam cut off is very sharp, so even slightly lower than they should be has a dramatic effect on their range.
Did you change them to RH dip for your ring/spa trip?
-
DasChin
- E30 Zone Regular

- Posts: 455
- Joined: Fri Mar 18, 2011 11:00 pm
cheers Brian
my car is a LHD 320is with LHD lights so they were still pants abroad!!
I have ordered the ones off flea bay so will see how I get on. its the 4300k kit H1 as you said.
its a track car that hardly gets used but as we get into winter then likelihood is I will get caught in the dark driving home.
Nick
my car is a LHD 320is with LHD lights so they were still pants abroad!!
I have ordered the ones off flea bay so will see how I get on. its the 4300k kit H1 as you said.
its a track car that hardly gets used but as we get into winter then likelihood is I will get caught in the dark driving home.
Nick
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
LHD or no, if you're using it on UK roads, and to pass a UK MOT test, the outer headlamps will need to dip to the left.
There is no difference between LHD and RHD E30 projector lights. They change from one to the other by loosening three screws at the rear and rotating the projector unit a few degrees.
There is no difference between LHD and RHD E30 projector lights. They change from one to the other by loosening three screws at the rear and rotating the projector unit a few degrees.
-
Demlotcrew
- E30 Zone Team Member

- Posts: 13329
- Joined: Mon Dec 20, 2004 11:00 pm
- Location: East Anglia
Brian are you sure there is no difference? and don't they have to dip to the right?
This is a great kit!
http://www.ebay.co.uk/itm/Genuine-PHILI ... 608wt_1041

This is a great kit!
http://www.ebay.co.uk/itm/Genuine-PHILI ... 608wt_1041
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Different part numbers, but the beam pattern on a RH drive E30 light switched to LH drive spec. is identical, apart from being a mirror image, of course. I expect the different part number is down to some trivial change, such as keeping the plug horizontal in their intended normal position.Demlotcrew wrote:Brian are you sure there is no difference? and don't they have to dip to the right?
E30 lights don't actually 'dip' as such,of course - they are permanently on all the time the headlamps are on, with a shaped beam, cutting off sharply some distance ahead, with a higher beam illuminating the nearside. 'Undipping' the lights simply adds a long range beam from the inner headlamps.
-
mrLEE30
- E30 Zone Team Member

- Posts: 6589
- Joined: Tue Jan 18, 2005 11:00 pm
- Location: Sweating buckets in Bahrain
just out of interest has no one considered that the guy may have the earlier lights?? which were pants...

-
Jhonno
- Homo Hair
- Posts: 20362
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: FLAT, FLAT, FLAT!!
He has a 320iS, so has smilies or bullets.. 
-
Demlotcrew
- E30 Zone Team Member

- Posts: 13329
- Joined: Mon Dec 20, 2004 11:00 pm
- Location: East Anglia
Brian, there is more of a reason for the different part numbers than plug alignment. Trust me, i was retrofitting Xenons to E30's when the zone first started, there is a big difference in the cut off and the projector body.Brianmoooore wrote:Different part numbers, but the beam pattern on a RH drive E30 light switched to LH drive spec. is identical, apart from being a mirror image, of course. I expect the different part number is down to some trivial change, such as keeping the plug horizontal in their intended normal position.Demlotcrew wrote:Brian are you sure there is no difference? and don't they have to dip to the right?
E30 lights don't actually 'dip' as such,of course - they are permanently on all the time the headlamps are on, with a shaped beam, cutting off sharply some distance ahead, with a higher beam illuminating the nearside. 'Undipping' the lights simply adds a long range beam from the inner headlamps.
Andrew


