We trying to remove the rear beam
Any ideas of how to get it off, everythings undone but it wont come off the 2 mounts.
Any ideas?
Thanks
Rear Beam Help
Moderator: martauto
-
hazd31
- E30 Zone Squatter

- Posts: 1689
- Joined: Sat Feb 07, 2009 11:00 pm
- Location: west sussex, nr brighton
-
hazd31
- E30 Zone Squatter

- Posts: 1689
- Joined: Sat Feb 07, 2009 11:00 pm
- Location: west sussex, nr brighton

-
johnl320
- E30 Zone Addict

- Posts: 3124
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Hampshire
support the trailing arms to stop the beam from trying to twist, remove the rear seat bottom to allow you to knock the bolts up from the centre of the beam bushes. Once they are out put a drift or extension bar up the centre of the bush and tap the bar from side to side to loosen it from the chassis, It may snap and leave a small ring of metal in the chassis, if it does then use a drill or dremel to remove the remaining material
-
hazd31
- E30 Zone Squatter

- Posts: 1689
- Joined: Sat Feb 07, 2009 11:00 pm
- Location: west sussex, nr brighton
really struggling, pushed the bolts through no problem, but we cant get it to move. broken a sledge hammer and a rubber mallet full of ball bearing.
cant get it to move
cant get it to move
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
I always run a hole saw up through the rubber, which allows the beam to just drop away so that you can deal with the remains of the centres with nothing in the way.
Any method of destroying the rubber?
Any method of destroying the rubber?
-
johnl320
- E30 Zone Addict

- Posts: 3124
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Hampshire
My IS rear beam fell off, leaving the centres in place, thats how knackered the bushes were, mot man didnt even spot them 
-
hazd31
- E30 Zone Squatter

- Posts: 1689
- Joined: Sat Feb 07, 2009 11:00 pm
- Location: west sussex, nr brighton
hole saw and some abuse did the trick
Just set alight to the bushes to get the metal bit out, then in with the new subframe!

Just set alight to the bushes to get the metal bit out, then in with the new subframe!

-
Barx325i
- Engaged to the E30 Zone

- Posts: 6493
- Joined: Wed Jul 26, 2006 11:00 pm
I like that one..Brianmoooore wrote:I always run a hole saw up through the rubber, which allows the beam to just drop away so that you can deal with the remains of the centres with nothing in the way.
Any method of destroying the rubber?
Then assemble a hack saw inside the remains of the bush in the beam - saw through the metal collar allowing it to deform - it will then tap out without too much of a problem.
-
johnl320
- E30 Zone Addict

- Posts: 3124
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Hampshire
good time to renew some brake pipes
-
e30topless
- E30 Zone Team Member

- Posts: 13595
- Joined: Wed Aug 23, 2006 11:00 pm
- Location: surrounded by scrap
has the beam lost the top diff mounting holes ? I would locate another if it has,hazd31 wrote:hole saw and some abuse did the trick
Just set alight to the bushes to get the metal bit out, then in with the new subframe!
-
hazd31
- E30 Zone Squatter

- Posts: 1689
- Joined: Sat Feb 07, 2009 11:00 pm
- Location: west sussex, nr brighton
This was the reason for the swap, good excuse to put the correct ratio diff on too!e30topless wrote:has the beam lost the top diff mounting holes ? I would locate another if it has,hazd31 wrote:hole saw and some abuse did the trick
Just set alight to the bushes to get the metal bit out, then in with the new subframe!
Snapped 2 mounts, one bolt and was hanging by the last bolt all twisted!
-
johnl320
- E30 Zone Addict

- Posts: 3124
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Hampshire
why bother burning the remains out of the knackered beam then?
