Was just wondering if I could use the water pump off of my older pre-facelift engine on the facelift engine I'm about to swap in, and if that would make the coolant hoses match up correctly with the pre-face rad.
The biggest thing I'm seeing off hand, is the overflow for the pre-face. The water pump swap would take care of that. And then the hose that runs from the thermostat housing along the passenger side of the block, to the heater core.... Facelift engine hose has a "T" in it, to run to the tank on the passenger wheel well. Can I just swap the non-"T" hose from the pre-facelift into here?
Facelift engine to Pre-facelift shell
Moderator: martauto
-
E30_Crazy
- E30 Zone Regular

- Posts: 733
- Joined: Fri Mar 05, 2010 11:00 pm
- Location: Alaska, USA (Lived in Brandon, Suffolk)
-
E30_Crazy
- E30 Zone Regular

- Posts: 733
- Joined: Fri Mar 05, 2010 11:00 pm
- Location: Alaska, USA (Lived in Brandon, Suffolk)
Anyone think this will work? I think I covered all the differences in the cooling systems...
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
What engine are you working on, to start with?
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
No reason why not,the water pump is the key to the thing,and that will match up to the rest of the system.
Youth is wasted on the young.
-
E30_Crazy
- E30 Zone Regular

- Posts: 733
- Joined: Fri Mar 05, 2010 11:00 pm
- Location: Alaska, USA (Lived in Brandon, Suffolk)
Yeah, guess that would help...
It's an M20B25 from a pre-facelift sport, being replaced by a facelift M20B25 (2.7)
I think I've got a hold of a header tank and rad for the facelift engine, so might not have to force the pre-facelift system on the facelift engine.
It's an M20B25 from a pre-facelift sport, being replaced by a facelift M20B25 (2.7)
I think I've got a hold of a header tank and rad for the facelift engine, so might not have to force the pre-facelift system on the facelift engine.
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
For M20's, the pumps are interchangeable, so as long as a pre-facelift pump is fitted, you can bolt up the rest of your pre-facelift cooling system to the facelift engine.
http://www.e30zone.net/e30zonewiki/inde ... ater_Pumps
http://www.e30zone.net/e30zonewiki/inde ... ater_Pumps
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
E30_Crazy
- E30 Zone Regular

- Posts: 733
- Joined: Fri Mar 05, 2010 11:00 pm
- Location: Alaska, USA (Lived in Brandon, Suffolk)
Yeah, I knew about the pumps, I was mainly wondering about the rest of the system. Mainly the hose with the T going to the fl header tank and the heater core (if I can just use the pre-fl one that doesn't go to the fl header tank, just straight back to the heater core)
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
Can see no reason why not,it's a bit like exhaust systems,use one or the other,but they do not 'mix and match'.E30_Crazy wrote:Yeah, I knew about the pumps, I was mainly wondering about the rest of the system. Mainly the hose with the T going to the fl header tank and the heater core (if I can just use the pre-fl one that doesn't go to the fl header tank, just straight back to the heater core)
Youth is wasted on the young.
-
e30topless
- E30 Zone Team Member

- Posts: 13595
- Joined: Wed Aug 23, 2006 11:00 pm
- Location: surrounded by scrap
you will need a pre-face pump and it's pipes, IIRC the pre- has 2 outlets on the bottom ?
