just changed over intrumet panel

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
JC1989
E30 Zone Newbie
E30 Zone Newbie
Posts: 75
Joined: Thu Jun 16, 2011 11:00 pm

Post Thu Sep 29, 2011 11:15 am

hi , was having trouble with my clocks, and rev cunter and mpg meter wasnt working properly, well when i swtched ignition on it the revs flicked from 0-1000 then when reving it when up and worked sometimes but then would stop working all together.

for the sake of 20 quid i went down the scrapyard and got some other clocks, which i have now plugged in and the rev counter sits at 1000 and doesnt move.

i have checked both circuit boards in these clocks and they seem fine ( no battery leakage)
i have also checked fuse number 21, which original was 20amp when it should have been 7.5 but upon changing did not make any difference.

what else could these be, could it be wireing ? what else should i check, many thanks
Jack
User avatar
Billwill
E30 Zone Regular
E30 Zone Regular
Posts: 363
Joined: Sun Jun 26, 2011 11:00 pm
Location: South Africa

Post Thu Sep 29, 2011 12:13 pm

Did you replace the whole cluster?
Apparently there is a plastic "coding" plug in the rear that you may need to swap over...this differentiates between 6 cyl and 4 cyl models. :?
User avatar
rover-2000
E30 Zone Newbie
E30 Zone Newbie
Posts: 226
Joined: Thu Aug 25, 2011 11:00 pm
Location: Walsall

Post Thu Sep 29, 2011 1:07 pm

JC1989 wrote:rev cunter
:jester:
Kind regards
John

1989 320i Touring
1993 E34 525i SE Touring
1979 Porsche 924 Lux
1982 Porsche 924 Lux
1985 Porsche 944 Lux
User avatar
JC1989
E30 Zone Newbie
E30 Zone Newbie
Posts: 75
Joined: Thu Jun 16, 2011 11:00 pm

Post Thu Sep 29, 2011 2:34 pm

Billwill wrote:Did you replace the whole cluster?
Apparently there is a plastic "coding" plug in the rear that you may need to swap over...this differentiates between 6 cyl and 4 cyl models. :?
ahh i did not know this? and it was a 4cylinder i took it out of. what is this coding plug thing then ? is it just the blue plug?
cheers
jack.
User avatar
mb15
E30 Zone Newbie
E30 Zone Newbie
Posts: 122
Joined: Tue Aug 24, 2010 11:00 pm

Post Thu Sep 29, 2011 4:29 pm

It's on the front bottom right of the cluster unit as you look at it.

A little white/cream plastic chip/plug that you squeeze the sides of and slot it out.
User avatar
JC1989
E30 Zone Newbie
E30 Zone Newbie
Posts: 75
Joined: Thu Jun 16, 2011 11:00 pm

Post Thu Sep 29, 2011 5:11 pm

oh rite, ye changed them over, not alot was hapening do i have to reprogram the unit? or leave it in for a while etc, what code shuld be on the one i need for a 6cylc and for a 4 cylc
cheers
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Thu Sep 29, 2011 7:54 pm

Rev. counter will still work with the wrong chip - just reads wrong. Nothing to reprogram either.
What type of batteries do your two SI boards have? AA sized NiCd batteries or much shorter lithium cells?
Make sure the lockring on the C101 main engine loom plug, next to the fusebox, is screwed right down. The rev. counter is sensitive to a poor connection here. (Black wire.)
User avatar
JC1989
E30 Zone Newbie
E30 Zone Newbie
Posts: 75
Joined: Thu Jun 16, 2011 11:00 pm

Post Thu Sep 29, 2011 11:32 pm

oh k , both boards have lithium batteries in , they are both half size aa batteries in them , on inspection both printed circuit boards are both clean with no signs of leakage.
i havent checked that c101 loom plug , will check tomorow,
seeing as both rev counters do different thing when plugged in could it come down to me having to sets of duff dials? altho is it only the printed circuit board that can be the downfull of these dials?
many thanks
User avatar
JC1989
E30 Zone Newbie
E30 Zone Newbie
Posts: 75
Joined: Thu Jun 16, 2011 11:00 pm

Post Thu Sep 29, 2011 11:38 pm

bu the way , if anyone could post up a picture of what a c101 plug looks like would be apreciated have searched on here and also looked on ebay to see if i could see what it looks like cheers.
User avatar
JC1989
E30 Zone Newbie
E30 Zone Newbie
Posts: 75
Joined: Thu Jun 16, 2011 11:00 pm

Post Fri Sep 30, 2011 5:39 pm

just checked the plug next to the fuse box took apart checked connections and put back to gether again ( i guess the c101 is the one that has 2 parts that screw together almost)
i also replaced every fuse with new ones today
no difference what so all, checked both circuit boards again on dash dials and they both look fine?
god knows whats the matter,
does anyone who lives local to me have a working dials with working rev counter on icould try to see if i have 2 sets of dodgy clocks
will be beer money in it for you
cheers
Jack
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Sep 30, 2011 7:21 pm

JC1989 wrote:oh k , both boards have lithium batteries in , they are both half size aa batteries in them
These batteries don't cause problems like the NiCd ones do. Even if they fail, the only effect is loss of the SI information if the main car battery is disconnected.
They do, however, have their own collection of (odd) problems, the most common of which is reading about 1000 RPM on the tacho when the engine is off.
I think it's very likely you have replaced one duff board with another duff board.
User avatar
JC1989
E30 Zone Newbie
E30 Zone Newbie
Posts: 75
Joined: Thu Jun 16, 2011 11:00 pm

Post Sun Oct 02, 2011 1:09 pm

rite u are spot on correct! one of the boards does display just 1000 rpm with the engine off, so i guess this is a duff
and the other flickers around like a crazy maniac when revving,

is this a case of getting new batteries? are these soldered in, look like there just pressed in, or is it a case of buying a new board (dials)

thanks for all your help
jonny323i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5428
Joined: Mon Mar 14, 2005 11:00 pm
Location: Stoke on trent

Post Sun Oct 02, 2011 1:24 pm

ive got 2 sets of clocks both should be ok especially one as i took it out of a working car if you want to buy another set
Touring for life
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Oct 02, 2011 2:22 pm

JC1989 wrote:rite u are spot on correct! one of the boards does display just 1000 rpm with the engine off, so i guess this is a duff
and the other flickers around like a crazy maniac when revving,

is this a case of getting new batteries? are these soldered in, look like there just pressed in, or is it a case of buying a new board (dials)

thanks for all your help
Batteries are all of the type with tags spot welded to the ends and are soldered in.
The NiCd batteries are rechargeable, and so are connected to the power rail that feeds other instruments. When these batteries fail they tend to go short circuit, dragging down the voltage on the rail, and messing up other instruments.
The lithium batteries are not rechargeable, and as a result are not connected to other instruments via the power rail. Their only purpose is to maintain the SI memory if, and only if, the main car battery is disconnected. They also don't have a tendency to short circuit, so the only effect of a failed lithium battery is that SI data is lost if the battery is disconnected.
Over this last weekend I've experienced yet another fault with a lithium type board that I've never seen before (only two green LEDs after reset), and am coming to the conclusion that these boards are best avoided in favour of the NiCd type, whose ONLY fault is battery failure.
Replace the aged batteries on these with NIMH ones (use 2/3 AA size to give more room) and they should be good for many years.
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Oct 02, 2011 2:26 pm

JC1989 wrote:one of the boards does display just 1000 rpm with the engine off,
This fault doesn't normally cause any other problems. In use the board works normally.
User avatar
JC1989
E30 Zone Newbie
E30 Zone Newbie
Posts: 75
Joined: Thu Jun 16, 2011 11:00 pm

Post Sun Oct 02, 2011 8:14 pm

Replace the aged batteries on these with NIMH ones (use 2/3 AA size to give more room) and they should be good for many years.
oh k thanks,
is this probably the best suggestion,
in which case is it hard to replace?
would these do the job
http://www.ebay.co.uk/itm/4-2-3-AA-800m ... 2a13fa28e1

i now these have tabs on the side, but woud the work? ( just a case of removing old and replacing with these, would they be the same size as the old ones>?
cheers for you time
Jack
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Oct 02, 2011 10:20 pm

These would work as replacements for the correct type of SI board, but can't be used as replacements on boards that use lithium batteries. The two types of board use different circuitry.
User avatar
JC1989
E30 Zone Newbie
E30 Zone Newbie
Posts: 75
Joined: Thu Jun 16, 2011 11:00 pm

Post Mon Oct 03, 2011 5:24 pm

Image s this the rite board for those batteries cheers
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Mon Oct 03, 2011 6:46 pm

The NiCd batteries are full AA sized, so that looks like a lithium celled board.