jacking points

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
jimbob29
E30 Zone Regular
E30 Zone Regular
Posts: 266
Joined: Tue Apr 26, 2011 11:00 pm
Location: isle of wight

Post Mon Sep 26, 2011 11:08 am

my front jacking points are looking a bit tattered and worn so im going to invest in a trolley jack so i dont have use jacking points anymore mabie rust treat them and underseal them ready for winter. were is the best place to place the trolley jack front/rear.
User avatar
VW-will
E30 Zone Regular
E30 Zone Regular
Posts: 369
Joined: Sun Apr 25, 2010 11:00 pm

Post Mon Sep 26, 2011 11:12 am

i use chassis rails at the front and then the bg nut bits that hold the rear beam on, hvae too driv e onto wood to get under the chassis rails though haha
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Mon Sep 26, 2011 11:13 am

Picture from a different site but this will help...


Image
User avatar
jimbob29
E30 Zone Regular
E30 Zone Regular
Posts: 266
Joined: Tue Apr 26, 2011 11:00 pm
Location: isle of wight

Post Mon Sep 26, 2011 11:40 am

do you use the wood because your car been lowered?if so will trolley jack fit under car mine been lowered 35mm front/rear will i have issues?its the rac bundle pack in argos lol
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Mon Sep 26, 2011 11:54 am

It all depends on the entry of your jack to be honest... You can buy low level entry jacks. Mine is only a keep RAC road side jack and car is lowered 40mm, don't have any problem getting the jack underneath and I have room for some planks of wood just to stop any damage, but usually I just jack it without wood.


Check the entry height of you jack and just get a tape measure and check there is clearance
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Mon Sep 26, 2011 1:08 pm

jimbob29 wrote:my front jacking points are looking a bit tattered and worn
If you're talking about the square metal pads just behind the wheel arch, those are NOT jacking points! They were places for the shell to be held by the factory robots, but are completely unsuitable for lifting a fully-equipped car, no matter what sort of jack you use.

Either use the BMW jack on the sill points, or a trolley jack on the chassis rails, but DON'T lift off the floor pan!
User avatar
jimbob29
E30 Zone Regular
E30 Zone Regular
Posts: 266
Joined: Tue Apr 26, 2011 11:00 pm
Location: isle of wight

Post Mon Sep 26, 2011 3:24 pm

no mate not those!dont want to jack car from sill points.just feel its probably safer to use trolley jack on chassis rail as you described thanks for the advice :D
User avatar
m8782538
E30 Zone Squatter
E30 Zone Squatter
Posts: 1550
Joined: Mon Feb 07, 2011 11:00 pm
Location: Swindon

Post Mon Sep 26, 2011 4:20 pm

Machine mart do a good one for just under £100, jacks up really quickly with a large pad area too. or you can get one as part of a kit like mine, i can use mine at the correct trolley jacking points or since mine has notches cut out of the pad area i can use it at the sill jacking points too.
asmith88
E30 Zone Addict
E30 Zone Addict
Posts: 2684
Joined: Sat Aug 23, 2008 11:00 pm
Location: Co Down, N.I

Post Mon Sep 26, 2011 7:48 pm

problem with the sill points is that the majority of jacks have a metal catch, so it just crushes the sill, make sure you get a good jack with a rubber mount
1990 brilliant red 318 is