M20 running VERY rich

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
Jacko_
E30 Zone Newbie
E30 Zone Newbie
Posts: 133
Joined: Sat Sep 12, 2009 11:00 pm
Location: Rossendale

Post Thu Sep 08, 2011 11:12 pm

I’ve only just built this engine back up now the car runs and i got the manifold fitted tonight so i could run it up to temp till today. I drove it up the road and power seems great in comparison to the 2.0 this 2.7 has replaced but the oil light flashed a little bit so headed back. Before all of this the engine seemed to run very rich while it was in the garage with lots of white smoke like steam but stinking loads of fuel.

So, i removed the dip stick to check the oil and it was very thin and clear in colour and stinks of fuel! :(

To say i'm devastated is an understatement!! Now i was angry and didn't stop to do a compression test but i'll do this tomorrow and report back with my findings but other than the rings being shot (they were fine before but the engine has been stood for a while) what else could be the problem?

Now I’ve heard that a faulty water temp sensor can cause it to over fuel ”“ do you know what reading I should get on this when testing it? I’ve got replacements (2nd hand) that I can swap out / compare against.

I’ve also heard that the airflow sensor can cause problems so I will try the other I have to see what that says”¦.this is all after dropping the oil and starting again of course but my question is what could cause this if it isn’t the rings? I just can’t see what else it could be but then it doesn’t blow any blue smoke so I don’t think its burning any oil. I could really do with some pointers as to what else could cause this problem of massive over fuel and if anyone knows a tuner in the Rossendale / North West area that can tune these engines please let me know as I’m thinking it would be worth getting it on a rolling road and a expert eye to examine it ”“ it’s either that or drop the fuel from the sump and chuck it over the car and set a match to it!
:evil:
E21 323i with 2.8 M52 on TBs (fast road / track car)
E28 M535i (track car project)
E36 328i touring (drift wagon daily driver)
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Fri Sep 09, 2011 10:38 am

Blue sensor on the thermostat housing is the ECU's way of measuring engine temp.

Using your meter,check it's resistance cold and hot,there should be a large difference in the readings.Repeat the check at the ECU plug,as this will check the wiring.

I have never played with one of those AFM's,but I understand that there is a track under the plastic top cover that can accumulate muck.

When the oil light was flickering,was there any odd engine noises?
Just wondering if the pressure switch is working properly...
Youth is wasted on the young.
User avatar
Jacko_
E30 Zone Newbie
E30 Zone Newbie
Posts: 133
Joined: Sat Sep 12, 2009 11:00 pm
Location: Rossendale

Post Fri Sep 09, 2011 1:12 pm

Hiya mate,

Yeah i read that the blue sensor is used by the ECU so will be checking this tonight as well as doing a compression test....

The oil light flickered on overrun and the engine apart from this light and the petrol in oil seems fine so i'm a little pissed / depressed over finding this. I'm assuming the light flickered due to how thin the oil is now it has petrol in it. I don't want to drive the car any further for fear of bore wash (if i do actually have good comp on all 6) and due to the low performance of the oil now its so thin.

Any other ideas as to what could cause it to run so rich other than knackered rings? Could the injectors themselves cause massive overfueling?
E21 323i with 2.8 M52 on TBs (fast road / track car)
E28 M535i (track car project)
E36 328i touring (drift wagon daily driver)
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Fri Sep 09, 2011 1:36 pm

Injectors are switched in threes,have you had them cleaned/serviced? It does make a difference!

I fixed rich running on one of my cars with a shiney new earth lead,the ECU/sensors run at odd voltages and although the thing would start at a normal cranking speed,the earth was not good enough to signal the ECU properly.
Youth is wasted on the young.
User avatar
Jacko_
E30 Zone Newbie
E30 Zone Newbie
Posts: 133
Joined: Sat Sep 12, 2009 11:00 pm
Location: Rossendale

Post Sat Sep 10, 2011 8:18 pm

Ok i've done a compression test and it all seems ok to me - results below;

Dry
Cyl 1 - 130psi
Cyl 2 - 120psi
Cyl 3 - 130psi
Cyl 4 - 120psi
Cyl 5 - 110psi
Cyl 6 - 120psi

Wet
(I’ll do this tomorrow and update i ran out of time today...)

Bit of a difference between them but i don't think it's big enough to be concerned about. I wish i had a leak down tool just to check.

I checked the two blue sensors i had (one in the old engine and the one in the new engine) i was getting some strange results when i checked the new engine sensor it looked like either my volt meter or the sensor is intermittently faulty. I checked them both cold and hot and got a large difference in readings on the old engine sensor so swapped it out, i will also swap the air flow meter for the one i know works.

I also dropped the oil, it's hard to say what its like but its already quite dark in colour, it does still smell of fuel but maybe some has evaporated off a little as it doesn't as bad as before. I steered it with my finger and it sure does look like it’s contaminated but hard to say if it’s a bit of water, a bit of fuel or a bit of both...i'll stick some fresh oil in tomorrow and do a wet test.
E21 323i with 2.8 M52 on TBs (fast road / track car)
E28 M535i (track car project)
E36 328i touring (drift wagon daily driver)
Rtaylor2208
E30 Zone Addict
E30 Zone Addict
Posts: 3004
Joined: Mon Oct 11, 2010 11:00 pm
Location: Ayr, Ayrshire, Scotland

Post Sun Sep 11, 2011 7:43 am

The blue sensor should read approx 300 OHMs when cold and 3000 When the car is warmed up. There have been loads of posts on here about it and a quick search should give you the range of values.
User avatar
Jacko_
E30 Zone Newbie
E30 Zone Newbie
Posts: 133
Joined: Sat Sep 12, 2009 11:00 pm
Location: Rossendale

Post Sun Sep 11, 2011 9:45 am

Hiya mate are you sure you got those figures the correct way around? I don't mean to question you but i got 2000 when cold and that dropped into the low hundreds when hot so its the other way around for my sensor readings.

I think a new battery in my multi meter is required and a re-test.
E21 323i with 2.8 M52 on TBs (fast road / track car)
E28 M535i (track car project)
E36 328i touring (drift wagon daily driver)
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Sep 11, 2011 10:18 am

Figures are definitely the wrong way around!
2000 - 4000 ohms when cold; around 300 ohms at normal engine temp.
Measure the resistance between the wire at the ECU connector and earth to check the wiring as well as the sensor.
A badly leaking injector will rapidly dump fuel into your oil.
User avatar
Jacko_
E30 Zone Newbie
E30 Zone Newbie
Posts: 133
Joined: Sat Sep 12, 2009 11:00 pm
Location: Rossendale

Post Sun Sep 11, 2011 4:11 pm

Thanks Brian, do you know how I can test each injector without ripping them out and getting them on one of those injector cleaning machines?
E21 323i with 2.8 M52 on TBs (fast road / track car)
E28 M535i (track car project)
E36 328i touring (drift wagon daily driver)
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Sep 11, 2011 10:03 pm

You can detect a cylinder that isn't firing by comparing the temperature of the exhaust primaries, especially if you have a six branch, but apart from comparing sparkplugs and hoping one is wet or decidedly blacker than the others, there isn't really any way of checking without having them on a test rig.
When were the injectors last rebuilt? If the answer is more than 50,000 miles ago, get them out and off to injectortune.
P.S: Something that might work, but never tried it: Pull out both the fuel pump relays and the DME relay, link pins 30 and 87 on the pump relay socket to make the pump run, and crank the engine for a while. You will have full fuel pressure, but the injectors won't be triggered, so a leaking one might give rise to a wet plug.
User avatar
Jacko_
E30 Zone Newbie
E30 Zone Newbie
Posts: 133
Joined: Sat Sep 12, 2009 11:00 pm
Location: Rossendale

Post Mon Sep 12, 2011 1:59 pm

Hi Brian

I've not got a heat gun nor is the 6 branch installed right now so i can't do this test. All that said i did run the car without the manifold and it was clear all were firing - of course i have no idea if any were over/under fueling.

I dropped the oil, refilled it, stuck some Forte gas treatment in the tank, and some oil enhancer and stem seal reconditioner in and i've done a few miles, i can't really tell what's going on or how much fuel is getting into the oil system or where from right now. I think getting the injectors off and onto the bench is the only way to illuminate them 100%.

After driving the car a little bit on the by-pass i can confirm the engine seems to run sweet and has plenty of power, it's night and day difference between this and the 2.0 that was so so flat.

Regards
Jacko.
E21 323i with 2.8 M52 on TBs (fast road / track car)
E28 M535i (track car project)
E36 328i touring (drift wagon daily driver)