My cabby has been slow to start for a while now, you have to turn it over for about 5 seconds before it comes to life.
I searched on here and have jumped the fuel pump relay to get the pump working before starting and then tried it and it fires first time so i'm assuming pressure is being lost in the fuel system somewhere. I've ordered a pressure guage so wil plumb that in during the week and see how much pressure i'm loosing and how quickly.
I've had a bit of a nose around and cant see any obvious leaks. Can somebody tell me where i can find the fuel filter on an 88 cabby (facelift engine). I've lifted the access panels under the rear seat and its not there, the fuel pump seems to be on the drivers side too. is that normal for cabbys?
also When i wired the pump to come on, I could here what sounds like flowing petrol running through the FPR. Is that normal? I'm a bit suspect of the FPR as it was second hand when i got it and looks a bit tired.
thanks
Loosing fuel pressure
Moderator: martauto
-
kman82
- E30 Zone Regular

- Posts: 967
- Joined: Mon Sep 22, 2008 11:00 pm
- Location: Oxford
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Pump's where it should be, and FPR noise is normal.
Filter should be in front of the LH rear wheel, where the old external pumps were fitted, or, failing that, low down in the rear left of the engine bay.
Connect up your pressure gauge, run the engine and switch off to confirm that residual fuel pressure is your problem, then repeat, but immediately after switching off, clamp off the fuel hose that runs from the FPR., and see if this maintains pressure. Repeat again, but this time clamp the hose that goes directly to the fuel rail, before where you've teed the gauge in.
If first test maintains pressure, it points towards a duff FPR; if the second test maintains pressure, the non return valve in the pump is the problem.
If neither test maintains pressure, then one or more injectors are the problem.
All assume that there are no simple leaks.
Filter should be in front of the LH rear wheel, where the old external pumps were fitted, or, failing that, low down in the rear left of the engine bay.
Connect up your pressure gauge, run the engine and switch off to confirm that residual fuel pressure is your problem, then repeat, but immediately after switching off, clamp off the fuel hose that runs from the FPR., and see if this maintains pressure. Repeat again, but this time clamp the hose that goes directly to the fuel rail, before where you've teed the gauge in.
If first test maintains pressure, it points towards a duff FPR; if the second test maintains pressure, the non return valve in the pump is the problem.
If neither test maintains pressure, then one or more injectors are the problem.
All assume that there are no simple leaks.
-
kman82
- E30 Zone Regular

- Posts: 967
- Joined: Mon Sep 22, 2008 11:00 pm
- Location: Oxford
Thanks Brian, that's really useful. Will report back when my gauge arrives
-
kman82
- E30 Zone Regular

- Posts: 967
- Joined: Mon Sep 22, 2008 11:00 pm
- Location: Oxford
My guage turned up today and I bought the wrong one, i bought a low pressure one.
I 've managed to find this on the web at a reasonable price. Do you think it will be ok on petrol rather than diesel? I cant think of any reason why it wouldn't be ok unless the diesel lines run at a different size and the push fit wont fit? If this kit is not suitable i'm going to have to take the car to the garage coz everything else i find is too expensive.
http://www.ldemporium.co.uk/diesel-fuel ... -1899.html
I 've managed to find this on the web at a reasonable price. Do you think it will be ok on petrol rather than diesel? I cant think of any reason why it wouldn't be ok unless the diesel lines run at a different size and the push fit wont fit? If this kit is not suitable i'm going to have to take the car to the garage coz everything else i find is too expensive.
http://www.ldemporium.co.uk/diesel-fuel ... -1899.html
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
-
kman82
- E30 Zone Regular

- Posts: 967
- Joined: Mon Sep 22, 2008 11:00 pm
- Location: Oxford
thank you Brian. Thats a bit of a bargain! ordered
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
You'll need around 6" of 8mm fuel hose to go with it.
-
kman82
- E30 Zone Regular

- Posts: 967
- Joined: Mon Sep 22, 2008 11:00 pm
- Location: Oxford
I was going to buy some new hose to replace the old ones at the same time. Are both 8mm or have i read correctly that one is 8mm and the other 9mm?
Also, to make you chuckle found this attached to the fuel line....


Also, to make you chuckle found this attached to the fuel line....


-
Jhonno
- Homo Hair
- Posts: 20362
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: FLAT, FLAT, FLAT!!
MAGIC BEANS!!!!kman82 wrote:I was going to buy some new hose to replace the old ones at the same time. Are both 8mm or have i read correctly that one is 8mm and the other 9mm?
Also, to make you chuckle found this attached to the fuel line....
-
kman82
- E30 Zone Regular

- Posts: 967
- Joined: Mon Sep 22, 2008 11:00 pm
- Location: Oxford
Hiya Brian, After waiting forever for the ebay gauge to arrive I've finally got out and run some tests, here's everything i've done so far...
Jumped relay pins..... 3.0 bar
Engine idle.... 2.6 - 2.8 bar flickering between the two
Breather hose removed... 3.0 bar
Engine swtiched off
After 5 minutes 2.2 bar
After 10 minutes 1.8 bar
Engine swtiched on, run for a couple of mins and off again
Hose clip on Return pipe from the FPR
After 5 mins 2.4 bar
After 10 mins 1.8 bar
Engine switched on, run for a couple of mins and off again
Hose clip on Fuel feed pipe
After 5 mins 2.4 bar
After 10 minutes 2.0 bar
What are your thoughts?
Ps, Would 7.5mm hose be ok to swap the rubber fuel hoses for? If not I'll have to order them in from BMW.
Thanks a million
Jumped relay pins..... 3.0 bar
Engine idle.... 2.6 - 2.8 bar flickering between the two
Breather hose removed... 3.0 bar
Engine swtiched off
After 5 minutes 2.2 bar
After 10 minutes 1.8 bar
Engine swtiched on, run for a couple of mins and off again
Hose clip on Return pipe from the FPR
After 5 mins 2.4 bar
After 10 mins 1.8 bar
Engine switched on, run for a couple of mins and off again
Hose clip on Fuel feed pipe
After 5 mins 2.4 bar
After 10 minutes 2.0 bar
What are your thoughts?
Ps, Would 7.5mm hose be ok to swap the rubber fuel hoses for? If not I'll have to order them in from BMW.
Thanks a million
-
kman82
- E30 Zone Regular

- Posts: 967
- Joined: Mon Sep 22, 2008 11:00 pm
- Location: Oxford
Brian, I re-read your post carefully and came to the conclusion that the injectors were to blame. I have had them cleaned with injectortune, cleaned everything and refitted and then voila! the car starts on the button! (well sort of, see my other thread re starter motor squeal!) Thanks for your help
http://www.e30zone.net/modules.php?name ... 09#2281209
http://www.e30zone.net/modules.php?name ... 09#2281209

