E46 rack fitted - catching on exhaust HELP!

Need technical Q/A then you're in the right place

Moderator: martauto

kman82
E30 Zone Regular
E30 Zone Regular
Posts: 967
Joined: Mon Sep 22, 2008 11:00 pm
Location: Oxford

Post Tue Sep 06, 2011 12:59 pm

So my car went in at the weekend to have my E46 rack fitted..

Image

I paid a garage to do the work for me in the end and didn't get to speak to the actually mechanic when i picked the car up this morning. I made up the steering coupling for them and it looks all ok. A bit snug but didn't catch.

Image

So i drove the car home and thought this is quality!! like a totally new car! THEN, after about 20 minutes when everything has warmed up, When you turn left, I can feel the steering grinding against the exhaust downpipes. It doesn't jamb up luckily but definately catches on there.

Image
Image

I've had a quick look where they fitted the rack and it seems to me to be in the rear holes, correct (by the way how can they leave that bracket so grimey!!)

Image

So what are my options? I dont have an angle grinder so cant grind down the corners of the steering coupling. Can i just dent a hole in the exhaust pipe? How big can i go and is it ok to hit it whilst attached to the car? Wont this restrict the airflow through the exhaust?

Thanks in advance

325i M20 by the way. as far as i know standard exhaust manifold
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Tue Sep 06, 2011 1:07 pm

New engine mounts for a start, if you use the Ford mounts they are less than half the price and actually firmer which will prevent the engine moving as much.

First though you need to go back and get them to refit the plastic dust guard back over the input shaft, I cant believe they left it off! :hammer:



You wont be changing back to an E30 rack then I take it? :D
kman82
E30 Zone Regular
E30 Zone Regular
Posts: 967
Joined: Mon Sep 22, 2008 11:00 pm
Location: Oxford

Post Tue Sep 06, 2011 1:27 pm

No mate, the rack felt unbelievable for the first 10 minutes when it wasn't grinding. cheers! They did say that one of the brackets wasn't quite right on the steering pipes though and had to be persuaded into place

Where does this plastic dust guard go, does it go over the orangey yellow bit on the rack itself?
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Tue Sep 06, 2011 1:42 pm

The orange/yellow is fresh grease I put in after cleaning the rack out, it does cover this to keep shite out away from the bearings. The only bracket would be on the return pipe and is slotted, I braze these on with the pipe fitted to a rack so they cannot be out of line, only explanation for it being out is the pipe got bent slightly either in the post or storage etc, they are easy to straighten out if you need to though :D
Just make sure the pipes are not touching the crossmember because it wont take long for them to rub through and start spraying :)
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Tue Sep 06, 2011 1:44 pm

Just found this - http://www.newfordpartsonline.co.uk/ind ... rod_detail

Im sure its these that are used as upgrades for M20 engines, 50mm tall same as standard
kman82
E30 Zone Regular
E30 Zone Regular
Posts: 967
Joined: Mon Sep 22, 2008 11:00 pm
Location: Oxford

Post Tue Sep 06, 2011 1:45 pm

Ok will check that, they said they managed to overcome the bracket pretty easy.

Right i'll get onto them and see where this dustcap is.

I'll get searching but is there any more info on the engine mounts?
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Tue Sep 06, 2011 1:49 pm

Im sure there is info on here somewhere about the mounts, had a quick search but couldnt find what I was looking for, someone might pipe up later on
kman82
E30 Zone Regular
E30 Zone Regular
Posts: 967
Joined: Mon Sep 22, 2008 11:00 pm
Location: Oxford

Post Tue Sep 06, 2011 1:59 pm

Think i found what i'm looking for here...

http://www.e30zone.net/modules.php?name ... ine+mounts

Any recomendations over burton power mounts and new ford parts centre?
kman82
E30 Zone Regular
E30 Zone Regular
Posts: 967
Joined: Mon Sep 22, 2008 11:00 pm
Location: Oxford

Post Sun Sep 25, 2011 6:58 pm

Bit of an udate, I went with the Buron power PF292 engine mounts in the end and had them fitted end of last week. they allow the engine to sit a bit higher and not rock around as much. No more clearance issues any more! Absolutely loving the E46 rack, what a difference!!
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Sun Sep 25, 2011 8:21 pm

:cool:
Ajsingh
E30 Zone Addict
E30 Zone Addict
Posts: 2378
Joined: Sun Mar 28, 2010 11:00 pm
Location: West Laaaandaan init! / Milton Keynes

Post Sun Sep 25, 2011 10:53 pm

So it was worn engine mounts which caused it to rub??

Will most probably have to do those before i put my 46 rack in too
E30 Crazy!