I Am just in the process of getting my AC working. I have had the necessary pipes made up. Now to the wiring.
I have found what i think is the magnetic clutch switch cable on the e30 loom side of things. Though when I press the AC button on the dash the button itself does not light up, neither do I get any Volt/amp reading off the Mag/switch plug with my meter.
I have checked the fuses and cant seem to see any which have gone. Are there any under the dash or in the button etc which I can also check? The blower still works and the button still activates fan when pressed.
Second issue is since i converted to Manual from auto I have not had my reverse lights working. Where abouts is the reverse light switch located on an auto? And where can I find the switch cables to be able to tap into to wire the manual switch into.
Many Thanks
Adem
A/C help & reverse switch help please.
Moderator: martauto
-
turk
- E30 Zone Squatter

- Posts: 1879
- Joined: Sun May 20, 2007 11:00 pm
- Location: Portsmouth
S54, S62, S65 & S85 Plug & Play loom/Ecu Kits
Sump Baffles
Engine Conversion Kits/Parts
TrackDays

Sump Baffles
Engine Conversion Kits/Parts
TrackDays

-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
Cannot help with air-con,sorry!
Reverse light switch should be on the driver's side of the gearbox,about halfway up.
From the switch,a twin core cable runs up through the rubber stick gaiter,and joins a matching socket that disappears under the carpet alongside the rear centre console.When the car was an auto,this bit would have been plugged into the inhibit socket at the selector.
Reverse light switch should be on the driver's side of the gearbox,about halfway up.
From the switch,a twin core cable runs up through the rubber stick gaiter,and joins a matching socket that disappears under the carpet alongside the rear centre console.When the car was an auto,this bit would have been plugged into the inhibit socket at the selector.
Youth is wasted on the young.
-
Billwill
- E30 Zone Regular

- Posts: 363
- Joined: Sun Jun 26, 2011 11:00 pm
- Location: South Africa
On my E30 M40 318i, there are two relays located behind where the radio sits....if you remove the radio...one relay is directly under the radio slot and the other relay is to the left of the slot.
The one relay energizes the other when the push button is pressed so you expect to have both relays energizes at the same time. One relay does not get its ground directly from the chassis but picks up its ground from the temperature control circuitry.
The two relays are so called "solid state " relays because they have some active components in them...transistors etc... that then energize the relay but you can replace them with normal relays BUT...the pin-outs are different.
The Haynes Manual has a reasonable generic circuit diagram for the air-con section.
Have a look to see if you have these relays and check with the Haynes manual.
I had failures of both relays and the grounding wire coming from the temperature control...I cut that wire and grounded it to the chassis rather.
The one relay energizes the other when the push button is pressed so you expect to have both relays energizes at the same time. One relay does not get its ground directly from the chassis but picks up its ground from the temperature control circuitry.
The two relays are so called "solid state " relays because they have some active components in them...transistors etc... that then energize the relay but you can replace them with normal relays BUT...the pin-outs are different.
The Haynes Manual has a reasonable generic circuit diagram for the air-con section.
Have a look to see if you have these relays and check with the Haynes manual.
I had failures of both relays and the grounding wire coming from the temperature control...I cut that wire and grounded it to the chassis rather.
-
lamby
- E30 Zone Regular

- Posts: 251
- Joined: Wed Jan 27, 2010 11:00 pm
also a/c needs to be charged before comp works,saves i burning out
-
Billwill
- E30 Zone Regular

- Posts: 363
- Joined: Sun Jun 26, 2011 11:00 pm
- Location: South Africa
As regards the amount of charge in the system, there is a "refrigerant low switch" located at the dryer in the right front of the engine bay. measure this to see if it is closed...if not you are low on refrigerant. You can temporary jumper this switch out to see if the AC clutch clicks in but do not run the the motor like this or as lamby has stated above...you will destroy the compressor.
Some of the compressors also have an overheat switch fitted on the side...you may have to jumper that out as well.
Some of the compressors also have an overheat switch fitted on the side...you may have to jumper that out as well.
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
As stated the pressure switch will stop the clutch engaging. Have you got an R134a retrofit kit for it?
-
turk
- E30 Zone Squatter

- Posts: 1879
- Joined: Sun May 20, 2007 11:00 pm
- Location: Portsmouth
its on its way, its only the add on valves isnt it? I gave a new dryer and new condenser so the switches etc should all be ok right?Have you got an R134a retrofit kit for it?
If i just add a positive feed to compressor that should engage clutch shouldnt it?
My button still wont light up though. It used to before I ripped the car apart :s
Need to check these relays in the dash
S54, S62, S65 & S85 Plug & Play loom/Ecu Kits
Sump Baffles
Engine Conversion Kits/Parts
TrackDays

Sump Baffles
Engine Conversion Kits/Parts
TrackDays

-
Billwill
- E30 Zone Regular

- Posts: 363
- Joined: Sun Jun 26, 2011 11:00 pm
- Location: South Africa
If you put 12 volts positive direct onto the AC clutch it should definitely energise unless it is burnt out or jammed. I had my compressor replaced recently with a re-furbished unit...the first one I got had a clutch that would attempt to close the gap but would not. I took that one back and got another re-furbished unit that worked fine.
Your blue button should light up....unless the bulb has decided to blow....if you find the missing voltage on the switch then the problems should be resolved.
Your blue button should light up....unless the bulb has decided to blow....if you find the missing voltage on the switch then the problems should be resolved.
-
bss325i
- E30 Zone Team Member

- Posts: 24532
- Joined: Sat Jan 20, 2007 11:00 pm
- Location: London/Surrey
No. The retro fit kit includes a few seals, a new refrigerant content label and most important, the valves and a new pressure switch.turk wrote:its on its way, its only the add on valves isnt it? I gave a new dryer and new condenser so the switches etc should all be ok right?
-
turk
- E30 Zone Squatter

- Posts: 1879
- Joined: Sun May 20, 2007 11:00 pm
- Location: Portsmouth
Ahh nice one!
S54, S62, S65 & S85 Plug & Play loom/Ecu Kits
Sump Baffles
Engine Conversion Kits/Parts
TrackDays

Sump Baffles
Engine Conversion Kits/Parts
TrackDays

-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
And the dryer 
-
bss325i
- E30 Zone Team Member

- Posts: 24532
- Joined: Sat Jan 20, 2007 11:00 pm
- Location: London/Surrey
Of course! 
