Touring load cover mounts - am I missing something?

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
batphink
E30 Zone Newbie
E30 Zone Newbie
Posts: 8
Joined: Wed Jan 11, 2006 11:00 pm

Post Sat Aug 27, 2011 12:09 pm

Hi all

I've just fitted a load cover with integral dog guard to my 316 toured and I can figure out if I've fitted it properly or not as it looks like I'm missing something. The mounts I've used are correct for the load cover (sturdier metal rather than standard plastic) but it just doesn't seem right. Does this look like I'm missing something?

Image
Image

As you can (hopefully) see the bit that sticks out within the arc on the end of the roller unit doesn't fit into the mount fully as it won't budge past this point to meet the spring at the bottom of the mount.

Anyone have any ideas?

Thanks
Ben

Thanks
Ben
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Sat Aug 27, 2011 1:24 pm

Is the roll cover properly pushed into the mounts? It looks to be sitting just proud of where it should be. Does the cover just pull of/out the way it is now?
BadDave
E30 Zone Team Member
E30 Zone Team Member
Posts: 6012
Joined: Sun Jan 09, 2005 11:00 pm
Location: Nr Aberdeen.Scotland(Gods country)

Post Sun Aug 28, 2011 1:06 am

Mounts fitted on the wrong sides .
Try swapping them over.

1st pic clearly shows the mount fitted on the wrong side.

:D
Last edited by BadDave on Sun Aug 28, 2011 7:20 pm, edited 2 times in total.
Alpina B10 3.2L #187 (1 of 64 brought into the UK)
2.8L turbo build thread(work in progress)
http://www.e30zone.net/modules.php?name ... 27#1268227
Morat
E30 Zone Team Member
E30 Zone Team Member
Posts: 8943
Joined: Thu Feb 09, 2006 11:00 pm
Location: The Peoples Republic of Yorkshire

Post Sun Aug 28, 2011 9:25 am

When it is all installed correctly the load cover/net will rock back to vertical when you snap it in.
E30 Touring 0.35 cD - more slippery than prison soap :)

Image
Praise the Lard... and pass the dripping!
User avatar
toby
E30 Zone Addict
E30 Zone Addict
Posts: 3609
Joined: Thu Aug 11, 2005 11:00 pm
Location: Kent

Post Sun Aug 28, 2011 7:04 pm

Yes swap the bits around as Dave said. You push it down, to depress the spring in the catch, then roll it forward or backward.
Image
User avatar
batphink
E30 Zone Newbie
E30 Zone Newbie
Posts: 8
Joined: Wed Jan 11, 2006 11:00 pm

Post Tue Aug 30, 2011 8:30 am

Thanks guys I already tried different potosi ms forthe mounts but I'll try again. As it is, it simply won't press in any further. The load cover rolls in and out just fine - in fact I found with the mountsthe other way round the cover was pressed into the speaker cover bit... Let you know how I get on.

Thanks!
User avatar
batphink
E30 Zone Newbie
E30 Zone Newbie
Posts: 8
Joined: Wed Jan 11, 2006 11:00 pm

Post Tue Aug 30, 2011 7:02 pm

That's done. Rocks back and forth a fair bit but thats probably just age as it fits much better now and pulling on the dog guard doesn't pull the whole thing out!

Thanks guys