m20 325i overheating issue

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
LagunaE30
E30 Zone Regular
E30 Zone Regular
Posts: 635
Joined: Mon Sep 21, 2009 11:00 pm

Post Tue Aug 16, 2011 3:03 am

okay, so went out for a drift night a few months ago, radiator got sliced open by the viscous( engine mounts gave way).
replaced the rad, viscous fan( not the coupling) just the plastic fan, and ever since the car has been overheating quite badly, the heater system blows out unbelievably hot air, i'm thinking it may be a blocked rad as the rad i fitted was off a car i broke a long time ago and was untested.
a lot of pressure builds up, overflow pipe pisses out steam and hot water, mostly the car overheats when i'm thrashing it on the motorway or during standstills in traffic, also it only overheats every now and then but does run warm most of the time ie between half and three quarter mark on the gauge.
any ideas on how i can fix this problem as it never happened before the incident, there is no mixing of oil and water, no mayo under the oil cap or in the expansiont ank.
regards
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Tue Aug 16, 2011 9:42 am

If the car runs properly when moving at a decent cruising speed, with the heater full on, then this does sound like a duff radiator, possibly along with a faulty viscous coupling.
Thermostat could be worth checking out as well.
User avatar
LagunaE30
E30 Zone Regular
E30 Zone Regular
Posts: 635
Joined: Mon Sep 21, 2009 11:00 pm

Post Sun Aug 21, 2011 8:07 pm

Hey brian ive completely removed the thermostat the water boils in the header tqnk could this be a sign of a cracked head?
User avatar
LagunaE30
E30 Zone Regular
E30 Zone Regular
Posts: 635
Joined: Mon Sep 21, 2009 11:00 pm

Post Sun Aug 21, 2011 8:07 pm

Hey brian ive completely removed the thermostat the water boils in the header tqnk could this be a sign of a cracked head?
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Aug 21, 2011 8:21 pm

Running without a thermostat it one way to get a cracked head! Reduces the flow around the back of the head.
If the water reaches boiling in the header tank, then it's not being cooled - either because the radiator isn't up to the job, the fan isn't, or just possibly the rotor's loose or broken up on the water pump.
What are the top and bottom radiator hoses like in terms of temperature? What's the heater output like?
User avatar
LagunaE30
E30 Zone Regular
E30 Zone Regular
Posts: 635
Joined: Mon Sep 21, 2009 11:00 pm

Post Sun Aug 21, 2011 10:47 pm

the heater output is very hot at times, and when the car begins to overheat the heaters will go cold occasionally.
i tried the newspaper test on the viscous fan and it came to a stop and did not shred the paper, to be honest the problem started when i changed the rad, i've been to a few local garages who have offered to have the head pressure tested but the car was absoloutely fine before the rad change.
i think i'll put a new rad on tomorrow and change the viscous and see if that makes any difference.
User avatar
LagunaE30
E30 Zone Regular
E30 Zone Regular
Posts: 635
Joined: Mon Sep 21, 2009 11:00 pm

Post Sun Aug 21, 2011 10:48 pm

the bottom hose is never as hot as the top pipe whenever the car begins to overheat, the top hose is often too hot to touch but the bottom is lukewarm.
when the car does start to overheat past the 3/4 mark i put the heaters on and they don't bring the temp down, also if i rev the vehicle before the temp hits the 3/4 mark the temp goes down, once it passes this point revving has no effect but to increase the temperature.
kman82
E30 Zone Regular
E30 Zone Regular
Posts: 967
Joined: Mon Sep 22, 2008 11:00 pm
Location: Oxford

Post Mon Aug 22, 2011 9:10 pm

If the viscous fan comes to a stop when the car is running hot then it's not working properly

Also make sure it's bled correctly
User avatar
LagunaE30
E30 Zone Regular
E30 Zone Regular
Posts: 635
Joined: Mon Sep 21, 2009 11:00 pm

Post Fri Aug 26, 2011 12:35 am

changed the viscous, car runs better, every now and then temp raises above half but never goes over 3/4, i bled the system again today and the temp now sits just above half, do you think its a good idea to change the rad?
kman82
E30 Zone Regular
E30 Zone Regular
Posts: 967
Joined: Mon Sep 22, 2008 11:00 pm
Location: Oxford

Post Fri Aug 26, 2011 9:31 am

you got anti freeze in it or just water?
User avatar
LagunaE30
E30 Zone Regular
E30 Zone Regular
Posts: 635
Joined: Mon Sep 21, 2009 11:00 pm

Post Fri Aug 26, 2011 2:58 pm

just water mate, you think anti-freeze would help?
kman82
E30 Zone Regular
E30 Zone Regular
Posts: 967
Joined: Mon Sep 22, 2008 11:00 pm
Location: Oxford

Post Fri Aug 26, 2011 3:06 pm

After i changed my water pump and messed around with collant system i had probs bleeding the system so make sure the front of the car is jacked up really high to get all the air out! takes a while so be patient and make sure the heater is in the right position (cant remember what now, you'll have to search)

I also noticed that running with the proper BMW anti-freeze over just water seemed to lower the temp sensor on the dash by about 1/8th!! i.e. mine always ran just over the half way mark and after with anti freeze it dropped to just below.
Curr946
E30 Zone Regular
E30 Zone Regular
Posts: 425
Joined: Tue Dec 23, 2008 11:00 pm
Location: Inverkeithing Fife

Post Fri Aug 26, 2011 3:15 pm

Running without anti freeze is a bad idea it can lead to problems with the water chambers rusting up and also cause problems within the alloy head
If your wife must learn to drive, don't stand in her way!
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Aug 26, 2011 7:01 pm

Curr946 wrote:Running without anti freeze is a bad idea it can lead to problems with the water chambers rusting up and also cause problems within the alloy head
And in a surprisingly short time!
Adding antifreeze to coolant actually REDUCES the coolant's ability to absorb heat from the engine, and that of the radiator to get rid of it, BUT more importantly, adding antifreeze raises the boiling point of the mixture, as does running the system under pressure.
Your thermostat mat keep the running temperature of the engine to an average of 88 degrees, or whatever rating of 'stat you have, but there are places in the recesses of the head where the temperature is way above 100 degrees, and without pressurisation and antifreeze in the coolant, local boiling will occur - an ideal recipe for a cracked head.
kman82
E30 Zone Regular
E30 Zone Regular
Posts: 967
Joined: Mon Sep 22, 2008 11:00 pm
Location: Oxford

Post Fri Aug 26, 2011 8:46 pm

Brian that makes perfect sense. Is it right that my temp reading would be slightly lower with antifreeze then, or is that likely to be just a coincidence?
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sat Aug 27, 2011 12:29 am

On a fully working cooling system, the engine running temperature, and hence the gauge reading, should be set totally and only by the water thermostat fitted. Antifreeze or not shouldn't affect the running temperature shown on the gauge.
User avatar
LagunaE30
E30 Zone Regular
E30 Zone Regular
Posts: 635
Joined: Mon Sep 21, 2009 11:00 pm

Post Sat Aug 27, 2011 5:22 am

i'll pop the thermostat back in tomorrow in that case and report my findings.
thanks to brian and kman82 for the help.
kman82
E30 Zone Regular
E30 Zone Regular
Posts: 967
Joined: Mon Sep 22, 2008 11:00 pm
Location: Oxford

Post Sat Aug 27, 2011 10:59 am

ahh, come to think of it, I did change the thermostat for a bmw one at the same time! sorry should of remembered that
User avatar
LagunaE30
E30 Zone Regular
E30 Zone Regular
Posts: 635
Joined: Mon Sep 21, 2009 11:00 pm

Post Sat Aug 27, 2011 9:14 pm

put the thermostat back in today didnt make much of a difference to the temp, i think its time to chnge the rad and then see if any difference is made.