Front disc backing plate fouling calliper carrier

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Thu Aug 25, 2011 9:44 pm

Hit a small snag earlier when rebuilding the front strut, the disc back plate fouls the calliper carrier :mad:

Some pics:
Image
Image
Image

There doesn't seem to be any movement to twist the backing plate, pretty confident the right plate it on the right strut, only thing I can think if is that it got bent a little when I was cleaning it with the anglgrinder and wirewheel?
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Fri Aug 26, 2011 12:59 am

You going to drive that thing or polish it?

If you are sure that you have not swapped the backplates from side to side,I would use a bit of hacksaw action...
Youth is wasted on the young.
Rav335uk
E30 Zone Meets/Events Team
E30 Zone Meets/Events Team
Posts: 27978
Joined: Wed Jan 19, 2005 11:00 pm
Location: Mad mad mad

Post Fri Aug 26, 2011 1:01 am

Carriers look to be the wrong way round. :mad:
Image
If you Got "Haters",Then your doing something Right!
CR24v??? Where's it all gone?? LOL
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Fri Aug 26, 2011 9:47 am

daimlerman wrote:You going to drive that thing or polish it?
Probably just polish it :mad: Hoping I get to drive it before winter :roll:

Thought that might have been it Rav, will check shortly when I get out to the car again.
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Aug 26, 2011 9:54 am

Rav335uk wrote:Carriers look to be the wrong way round. :mad:
Been there, done this! Pretty sure it was the carriers on the wrong side, as Rav says.
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Fri Aug 26, 2011 2:16 pm

I swapped carriers, their both the same and still fouling the plate. I'm going to put it down to the back plate being bent/warped from cleaning it up with the wirewheel. I just chopped the tips of bot carriers of :D
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Aug 26, 2011 2:28 pm

Might have been the backplates on the wrong side then. I know the cure was to swap something from side to side!
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Fri Aug 26, 2011 2:35 pm

I don't think they can go on wrong though, the 3 holes in the plate aren't the same distance from each other. Their on now with the bearings done up and their not coming of for the sake of replacing the plates.

Which side of the car is the sensor for the pads on?
E30BeemerLad
Married to the E30 Zone
Married to the E30 Zone
Posts: 16806
Joined: Mon Mar 28, 2005 11:00 pm
Location: Norfolk

Post Fri Aug 26, 2011 2:37 pm

I think it is passenger side but not 100%
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Fri Aug 26, 2011 2:46 pm

Backing plates are on right then, passenger side has the sensor bracket on it.