Bad vibrations

Need technical Q/A then you're in the right place

Moderator: martauto

Cloggy Saint
Old Skooler
Old Skooler
Posts: 8027
Joined: Sun Jan 09, 2005 11:00 pm
Location: zummerzet

Post Wed Aug 24, 2011 7:22 pm

My touring has an extremely annoying vibration that I need to sort out. It's quite a harsh vibration that seems to affect the whole car but I especially feel it through the pedals and floor pan and it tends to be worse when accelerating in 5th from low revs. Over the last couple of years I've replaced all suspension parts/bushes etc but I've never done the engine or gearbox mounts or the prop' centre bearing. I know it's a bit vague but can anyone offer some suggestions?
Image

E30 zone - promoting adult illiteracy since 2004
User avatar
threelander
E30 Zone Camper
E30 Zone Camper
Posts: 1166
Joined: Fri Jan 14, 2011 11:00 pm

Post Wed Aug 24, 2011 7:28 pm

did you replace the donut between gear box and prop it sounds like a problem i had and this was the culprit
Green
E30 Zone Squatter
E30 Zone Squatter
Posts: 1698
Joined: Wed Mar 17, 2010 11:00 pm
Location: Santa Pod

Post Wed Aug 24, 2011 11:21 pm

Gearbox mounts when they're gone usually cause a clunk when changing gear, sounds like it could be the prop donut or other moving part.
Image
Cloggy Saint
Old Skooler
Old Skooler
Posts: 8027
Joined: Sun Jan 09, 2005 11:00 pm
Location: zummerzet

Post Thu Aug 25, 2011 6:41 am

Thanks for that, I guess I'll be starting with the donut, which part is it? :mad:

http://www.realoem.com/bmw/showparts.do ... 10&lang=en
Image

E30 zone - promoting adult illiteracy since 2004
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Thu Aug 25, 2011 10:02 am

Unsurprisingly, it's the most expensive part on that list: 26111225624
Cloggy Saint
Old Skooler
Old Skooler
Posts: 8027
Joined: Sun Jan 09, 2005 11:00 pm
Location: zummerzet

Post Thu Aug 25, 2011 5:46 pm

Thanks for that. Final question, is it the sort of job a cack-handed spanner spas' like myself can do?
Image

E30 zone - promoting adult illiteracy since 2004
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Thu Aug 25, 2011 6:55 pm

User avatar
threelander
E30 Zone Camper
E30 Zone Camper
Posts: 1166
Joined: Fri Jan 14, 2011 11:00 pm

Post Thu Aug 25, 2011 7:13 pm

nice one that grrrr
i let a garage do mine first time and they put all the bolts in the same way the tossers so ended up doing it again myself 12 months later.so the answer to your question is no it,s not a difficult job at all if all the bolts are facing the right way mate.i,m sure you will be ok but i would fit new prop centre bearing at same time cloggy
Cloggy Saint
Old Skooler
Old Skooler
Posts: 8027
Joined: Sun Jan 09, 2005 11:00 pm
Location: zummerzet

Post Thu Aug 25, 2011 7:16 pm

8O Thanks!
Image

E30 zone - promoting adult illiteracy since 2004