Hi all:
Im having a problem with my 325i motronic 1.3.
Its idling silly high at times - anything between 1000 - 2000 rpm, it varies each time bizzarly. The revs will stay steady whilst its doing this and blipping the throttle dosent make any difference.
The fault seems to occur randomly - and will behave perfectly normal the next time you start her up.
What is the best way to fault find this - the ecu must be controlling it as the throttle cable/butterfly are in the normal closed position when the fault happens.
Could it be a faulty ICV?
idle issue
Moderator: martauto
-
darren_mk
- E30 Zone Newbie

- Posts: 247
- Joined: Sun Jan 28, 2007 11:00 pm
- Location: Northern Ireland
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
ICV could be sticking - common with LPG converted cars, where the ICV operates at a different position from where it has for the first twenty years of its life.
Try removing it and cleaning it through with carb. cleaner as a first step.
The ICV on a 325 should stay exactly where it is if unplugged while the engine is running, and the idle speed should only change if the load on the engine changes.
Try removing it and cleaning it through with carb. cleaner as a first step.
The ICV on a 325 should stay exactly where it is if unplugged while the engine is running, and the idle speed should only change if the load on the engine changes.
-
darren_mk
- E30 Zone Newbie

- Posts: 247
- Joined: Sun Jan 28, 2007 11:00 pm
- Location: Northern Ireland
When i disconnected the icv when the engine was running it stalled - does this indicate a fault?
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
325 ICV is a balanced armature affair - effectively two motors pulling against each other, so should just stay put when the plug is pulled, at whatever opening it happens to be at.
-
darren_mk
- E30 Zone Newbie

- Posts: 247
- Joined: Sun Jan 28, 2007 11:00 pm
- Location: Northern Ireland
So what you are saying is that disconnecting the icv will not make the car stall?
If so then as i removed the plug on the icv i might have pulled on its connection into the rubber elbow causing an air leak.....
So that leaves me back to square one! What else would cause a high idle?
If so then as i removed the plug on the icv i might have pulled on its connection into the rubber elbow causing an air leak.....
So that leaves me back to square one! What else would cause a high idle?
-
darren_mk
- E30 Zone Newbie

- Posts: 247
- Joined: Sun Jan 28, 2007 11:00 pm
- Location: Northern Ireland
Anyone shead any more light on this?
Started it up yesterday and it idled perfect - then went on a 10 minute drive and the idle had raised up to 1400 rpm.....
Started it up yesterday and it idled perfect - then went on a 10 minute drive and the idle had raised up to 1400 rpm.....
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
The most likely idle related component to behave sometimes and not others is the idle switch part of the throttle position switch.
This must be set to switch 'on' with the throttle closed onto its stop, but to switch 'off' as soon as possible after the throttle leaves its stop as the accelerator pedal is pressed.
It's a microswitch, so will have a certain amount of hysteresis built into its action, but this should be small. Because of its mounting position at the bottom of the butterfly shaft, oil in the intake pipework (from the engine breather system), tends to run down anget trapped inside it, gumming it up.
A 1mm hole drilled right in the middle of the underside of the switch will let any accumulated oil out, and let you get some switch cleaner in there.
This must be set to switch 'on' with the throttle closed onto its stop, but to switch 'off' as soon as possible after the throttle leaves its stop as the accelerator pedal is pressed.
It's a microswitch, so will have a certain amount of hysteresis built into its action, but this should be small. Because of its mounting position at the bottom of the butterfly shaft, oil in the intake pipework (from the engine breather system), tends to run down anget trapped inside it, gumming it up.
A 1mm hole drilled right in the middle of the underside of the switch will let any accumulated oil out, and let you get some switch cleaner in there.
