Rear beam

Need technical Q/A then you're in the right place

Moderator: martauto

Duke137
Married to the E30 Zone
Married to the E30 Zone
Posts: 7207
Joined: Sat Aug 29, 2009 11:00 pm

Post Thu Aug 11, 2011 10:02 pm

Plan on dropping the rear beam on my project car and replacing:

Trailing arms for rear disc conversion
Trailing arm bushes
Rear beam bushes
Upgrading to a 3.64 medium case diff (open)
Handbrake cables
Rear pads and discs if required (unsure yet)
Replacing the 55L tank for a 63L one

My question is what do I need to get from the stealers?

Example: nuts, bolts, anything really??

What can I get away with re-using? Don't mind buying a few bits but this isn't going to be a show piece....

thanks
How do you pronounce 'either'? I say 'either', but some say 'either'. Either is correct.
TouringMatt
E30 Zone Camper
E30 Zone Camper
Posts: 1188
Joined: Mon Jan 10, 2005 11:00 pm
Location: Not where i should be

Post Thu Aug 11, 2011 10:36 pm

If there is any doubt about the condition of the handbrake back plates, swap them for new, nowt worse than the handbrake retaining pins pulling through.
Its a bearing/drive flange removal job - or you can cut/bent/re-shape and weld them back together
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Fri Aug 12, 2011 12:48 am

You will need bushes,new handbrake cables...as the old one's rarely come out in one piece.

If you are stripping the trailing arms,new back plates are a very good idea.

Everything you need,except for the back plates,can come from GSF/ECP.

If you are having the fuel tank out as well,do not forget to swap the fuel filter!
Youth is wasted on the young.
capri_rob
Married to the E30 Zone
Married to the E30 Zone
Posts: 9678
Joined: Tue Feb 19, 2008 11:00 pm
Location: South Staffordshire

Post Fri Aug 12, 2011 8:20 am

Ferg

Trailing arm bushes from dealer
Subframe bushes from ECP
Handbrake cables ECP ( but think dealer price is roughly the same so you might want to compare the cost before buying )
Pads & Disks ECP - Textar ideally although you can get Brembo branded disks via Ebay quite cheaply now.
Might as well do the wheel bearings as well before you put it on the car - I'd take the arms to a garage and get them to press the old ones out and new ones in for beer tokens

:wink:
Image

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
Duke137
Married to the E30 Zone
Married to the E30 Zone
Posts: 7207
Joined: Sat Aug 29, 2009 11:00 pm

Post Fri Aug 12, 2011 7:14 pm

Cheers guys, I'll email meatballbag for some prices....

I've got trailing arm bushes, and handbrake cables, good discs, just need new pads.

What about nuts and bolts ?
How do you pronounce 'either'? I say 'either', but some say 'either'. Either is correct.
magpie
Old Skooler
Old Skooler
Posts: 28035
Joined: Sun Jun 29, 2008 11:00 pm
Location: Consett,Durham.

Post Fri Aug 12, 2011 7:31 pm

you might need the rear beam plates that bolt to the cills,i've had to grind a few of the bolts out from here in the past.

4,5,and 6

Image
Image
m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds :)
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Fri Aug 12, 2011 9:19 pm

Be careful buying nuts and bolts from the dealer, even they haven't escaped the ridiculous price increases, the big washers that fit above the rear subframe bush's are over £5 each now :mad:
Duke137
Married to the E30 Zone
Married to the E30 Zone
Posts: 7207
Joined: Sat Aug 29, 2009 11:00 pm

Post Fri Aug 12, 2011 9:43 pm

DanThe wrote:Be careful buying nuts and bolts from the dealer, even they haven't escaped the ridiculous price increases, the big washers that fit above the rear subframe bush's are over £5 each now :mad:
eeesh :roll:

cheers boys n girls (Dan) :D
How do you pronounce 'either'? I say 'either', but some say 'either'. Either is correct.
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Sat Aug 13, 2011 2:29 am

Those mounting bolts(number 6)

I slice 'playfull' one's off from the inside of the sill,using Mr Angle Grinder,cutting the captive nut off.Going back,a 25mm M8 nut and bolt from your local nut and bolt shop is all you need.
Youth is wasted on the young.
User avatar
Rodderz
E30 Zone Addict
E30 Zone Addict
Posts: 3105
Joined: Thu Nov 24, 2005 11:00 pm
Location: Southampton

Post Sat Aug 13, 2011 3:29 am

magpie wrote:you might need the rear beam plates that bolt to the cills,i've had to grind a few of the bolts out from here in the past.

4,5,and 6

Image
What is part# 3 called?
Barx325i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6493
Joined: Wed Jul 26, 2006 11:00 pm

Post Sat Aug 13, 2011 3:33 am

rear beam bush
capri_rob
Married to the E30 Zone
Married to the E30 Zone
Posts: 9678
Joined: Tue Feb 19, 2008 11:00 pm
Location: South Staffordshire

Post Sat Aug 13, 2011 9:47 am

Ferg pretty sure I've got the big washers and beam plates "in stock" if you need them - had to do the "angle grinder delete" on the captive nuts on the beam plates but Malc's solution works :D
Image

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
Barx325i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6493
Joined: Wed Jul 26, 2006 11:00 pm

Post Sat Aug 13, 2011 12:29 pm

capri_rob wrote:"angle grinder delete"
angle grinders rock..

I have a pair of brand new no.5's which should make it look nice & tidy, I'll fish them out if you need some

Thinking about it, I have decent no.4's also
Duke137
Married to the E30 Zone
Married to the E30 Zone
Posts: 7207
Joined: Sat Aug 29, 2009 11:00 pm

Post Sun Aug 14, 2011 11:40 pm

capri_rob wrote:Ferg pretty sure I've got the big washers and beam plates "in stock" if you need them - had to do the "angle grinder delete" on the captive nuts on the beam plates but Malc's solution works :D
Hi Rob, yes please mate!

I was scratching my arse on how to remove the rear beam and those bolts?? I gave up because I had a hangover today after an all day session yesterday 8O

I'll take those spares aswell please barx, will drop you both PM's now :)
How do you pronounce 'either'? I say 'either', but some say 'either'. Either is correct.
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Mon Aug 15, 2011 10:51 pm

4's and 5's should be powder coated regardless of how new they are, same with 1's and 8's :)
Oh, and why cut the captive nut off? Cut the bolt head off then once the plate is off remove the stud with a bit of heat and mole grips, clean the thread out afterwards and then you can be civilised and fit just bolts rather than landrover spec nut and bolt bodgery :P
Duke137
Married to the E30 Zone
Married to the E30 Zone
Posts: 7207
Joined: Sat Aug 29, 2009 11:00 pm

Post Mon Aug 15, 2011 10:58 pm

How much does that cost to powdercoat 1 and 8 roughly?
How do you pronounce 'either'? I say 'either', but some say 'either'. Either is correct.
Kedge
Old Skooler
Old Skooler
Posts: 7698
Joined: Thu Jan 13, 2005 11:00 pm
Location: Leicestershire

Post Mon Aug 15, 2011 11:23 pm

Balls to it, watching this now. Will be stripping out the back end of mine now since i can't fathom out how to get the tank in.

Ferg let me know the costs from Matt if you don't mind, i've got to get hold of a spare beam and the arms yet. Got some new BMW rear beam bushes kicking about though :)
Image
'86 Polaris 316 M20B28 Rebuild
Instagram - Kedge85
Duke137
Married to the E30 Zone
Married to the E30 Zone
Posts: 7207
Joined: Sat Aug 29, 2009 11:00 pm

Post Mon Aug 15, 2011 11:32 pm

Will do Dave
How do you pronounce 'either'? I say 'either', but some say 'either'. Either is correct.
Duke137
Married to the E30 Zone
Married to the E30 Zone
Posts: 7207
Joined: Sat Aug 29, 2009 11:00 pm

Post Tue Aug 16, 2011 7:40 pm

When removing the beam is it easier to detatch the trailing arms and diff?
How do you pronounce 'either'? I say 'either', but some say 'either'. Either is correct.
capri_rob
Married to the E30 Zone
Married to the E30 Zone
Posts: 9678
Joined: Tue Feb 19, 2008 11:00 pm
Location: South Staffordshire

Post Tue Aug 16, 2011 7:49 pm

Nope.

If the beam is stuck in place the weight of the diff and arms will help - you might still need to give it some welly with the tapping-stick to free it :D
Image

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
Duke137
Married to the E30 Zone
Married to the E30 Zone
Posts: 7207
Joined: Sat Aug 29, 2009 11:00 pm

Post Tue Aug 16, 2011 8:00 pm

What the fook is it stuck on?
How do you pronounce 'either'? I say 'either', but some say 'either'. Either is correct.
capri_rob
Married to the E30 Zone
Married to the E30 Zone
Posts: 9678
Joined: Tue Feb 19, 2008 11:00 pm
Location: South Staffordshire

Post Tue Aug 16, 2011 8:07 pm

The aluminium centres of the beam bushes sometimes weld themselves into the bodywork - corrosion between the aluminium of the bush and the metal of the bodywork can make them very difficult to separate.

if you're really unlucky the aluminium bush centre will snap off and you'll have to drill it out :eek:

Passenger side one bust off on this pic :banghead:

Image

Just make sure none of you is under any part of the beam when it does let go as its about as heavy as a medium-sized planet- a decent trolley jack is essential :D
Image

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
Bristol_Jer
E30 Zone Addict
E30 Zone Addict
Posts: 2523
Joined: Thu Sep 24, 2009 11:00 pm
Location: Bristol, UK

Post Tue Aug 16, 2011 8:18 pm

I had this problem with the aluminium sleeve welding itself to the bodywork, I used a Dremel with a grinding attachment to carefully grind away the aluminium. Doesn't take too long but make sure you wear goggles!
Duke137
Married to the E30 Zone
Married to the E30 Zone
Posts: 7207
Joined: Sat Aug 29, 2009 11:00 pm

Post Tue Aug 16, 2011 10:37 pm

:cry: gave up it got dark and I have the gay 55L tank pipe stopping me dropping the prop with it all and I the bolts are solid

I banged my head, swore and fooked off in the house :D
How do you pronounce 'either'? I say 'either', but some say 'either'. Either is correct.
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Tue Aug 16, 2011 10:49 pm

Rob, you are wrong. Leaving the arms and diff attached just makes it more difficult, as they twist the beam mounting against the studs.
Taking the arms and diff off first is the best way to do it. Same with the refit.
Kedge
Old Skooler
Old Skooler
Posts: 7698
Joined: Thu Jan 13, 2005 11:00 pm
Location: Leicestershire

Post Tue Aug 16, 2011 10:50 pm

It's a grim job isn't it :(
Image
'86 Polaris 316 M20B28 Rebuild
Instagram - Kedge85
capri_rob
Married to the E30 Zone
Married to the E30 Zone
Posts: 9678
Joined: Tue Feb 19, 2008 11:00 pm
Location: South Staffordshire

Post Wed Aug 17, 2011 7:31 am

DanThe wrote:Rob, you are wrong. Leaving the arms and diff attached just makes it more difficult, as they twist the beam mounting against the studs.
Taking the arms and diff off first is the best way to do it. Same with the refit.
:eek: Done 3 with Mark now and taking off have left the lot on !

On refit have fitted the diff but left the arms off to put the beam in place, but the O/S of the beam you have to drop back down when its on the car to fit the the trailing arm because of filler pipe clearance issues - you need about 4 pairs of hands !
Image

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Wed Aug 17, 2011 8:43 am

capri_rob wrote:
DanThe wrote:Rob, you are wrong. Leaving the arms and diff attached just makes it more difficult, as they twist the beam mounting against the studs.
Taking the arms and diff off first is the best way to do it. Same with the refit.
:eek: Done 3 with Mark now and taking off have left the lot on !

On refit have fitted the diff but left the arms off to put the beam in place, but the O/S of the beam you have to drop back down when its on the car to fit the the trailing arm because of filler pipe clearance issues - you need about 4 pairs of hands !
Last that I did(cabbie),I bolted the beam in first.Then the dif,now the thing is secured at all three mounting points.Then the trailing arms were slotted in.
No need to disturb the beam at all....just line the t/a bushes up and slot the bolts through!

I assembled the entire thing off the car when I did the touring,that is;
Beam
Diff
Trailing arms

Then offered the lot up in one hit,I had it 'balanced' on spare wheels and blocks of timber and found that it was a proper bugger to bolt home,it went,but I struggled and struggled,and next doors kids learnt a whole new vocabulary and I swore that next time it would go back in bits,just for the ease of lifting.
Youth is wasted on the young.
Duke137
Married to the E30 Zone
Married to the E30 Zone
Posts: 7207
Joined: Sat Aug 29, 2009 11:00 pm

Post Wed Aug 17, 2011 9:16 am

Thanks for the advice! I think I will disconnect the trailing arms and diff (hopefully tonight)
How do you pronounce 'either'? I say 'either', but some say 'either'. Either is correct.
nickso
E30 Zone Addict
E30 Zone Addict
Posts: 4396
Joined: Sat Jul 23, 2005 11:00 pm
Location: Go do that voodoo that you do so welllllllll!!

Post Wed Aug 17, 2011 9:27 am

If it's stuck on the beam bushes put in a bolt the same thickness as the bush bolt with a bit sticking out the bottom and belt the hell out of it side to side, that usually gets them free for me but sometimes does break the inner part. If it does break getting the inner bit out isn't much of a chore really. I use a sharp chisel and my weeks quota of patience.
Image

'88 e30 328i M52 track bint.
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Aug 17, 2011 9:37 am

Run a deep hole saw up through the bush each side, and the beam just drops off, first time, every time. Doesn't deal with the problem of the aluminium insert, but at least it's all exposed and you can see what you're doing.
I actually use two hole saws - one that just fits inside the steel outer sleeve, and one that just clears the inner bush. All the rubber gone in one simple process.
Duke137
Married to the E30 Zone
Married to the E30 Zone
Posts: 7207
Joined: Sat Aug 29, 2009 11:00 pm

Post Tue Aug 23, 2011 1:09 pm

Can the Top washers be Re-used if I bead blast them at work? does anyone know?
How do you pronounce 'either'? I say 'either', but some say 'either'. Either is correct.
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Tue Aug 23, 2011 1:43 pm

I can see no reason why not....
Youth is wasted on the young.