Gearbox code and high comp pistons dumb questions
Moderator: martauto
-
FEP
- E30 Zone Regular

- Posts: 309
- Joined: Sat May 24, 2008 11:00 pm
- Location: Hackney (of carriage fame) London
The Bentley Manual says that the gearbox on my M20B25 motor should have an identification number on the top of the bellhousing. With the head off and having cleaned thoroughly, there is no number there at all. Anyone know what I should make of this?
Also, as my car is a pre-facelift and so theoretically a high compression engine, I expected the pistons to be domed. They are dished. Does this mean that my engine is actually low compression? How would I know?
Also, as my car is a pre-facelift and so theoretically a high compression engine, I expected the pistons to be domed. They are dished. Does this mean that my engine is actually low compression? How would I know?
-
gooner1
- Out humping Reindeer
- Posts: 13280
- Joined: Fri Apr 14, 2006 11:00 pm
- Location: Northampton.For my sins.
FEP, your pistons should be like this.


[/quote]
Born and bred in Mare Street btw.



[/quote]Born and bred in Mare Street btw.

-
FEP
- E30 Zone Regular

- Posts: 309
- Joined: Sat May 24, 2008 11:00 pm
- Location: Hackney (of carriage fame) London
They are. So when they lowered the CR must have BIG dishes in 'em.
-
Barx325i
- Engaged to the E30 Zone

- Posts: 6493
- Joined: Wed Jul 26, 2006 11:00 pm
have a look at your engine ID code and report back..
If it went like a scalded whippet, it's high comp, if it just pulled like a train, it's a K model
If it went like a scalded whippet, it's high comp, if it just pulled like a train, it's a K model
-
FEP
- E30 Zone Regular

- Posts: 309
- Joined: Sat May 24, 2008 11:00 pm
- Location: Hackney (of carriage fame) London
Though the id code wouldn't reflect any past change of pistons presumably.Barx325i wrote:have a look at your engine ID code and report back..
If it went like a scalded whippet, it's high comp, if it just pulled like a train, it's a K model
-
Barx325i
- Engaged to the E30 Zone

- Posts: 6493
- Joined: Wed Jul 26, 2006 11:00 pm
well no you are quite right, but 6 pistons out and in is reasonably major surgery, it's not unknown, but pretty rare
-
e301988325i
- E30 Zone Addict

- Posts: 3701
- Joined: Fri Feb 01, 2008 11:00 pm
- Location: Taunton, Somerset
Which is on the near side of the engine block just behind the engine mount and just above the sump/block interface stamped on a flat machined area.Barx325i wrote:have a look at your engine ID code and report back..
If it went like a scalded whippet, it's high comp, if it just pulled like a train, it's a K model
I said:
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
-
FEP
- E30 Zone Regular

- Posts: 309
- Joined: Sat May 24, 2008 11:00 pm
- Location: Hackney (of carriage fame) London
25 6E
So it's high comp it would seem
pacerpete has sold me a 9.4:1 lump. (medium comp?)
How much weaker is it going to feel given that I'm sticking with my presumably Motronic 1.1 ignition.
Anyone got any thoughts about the missing gearbox code? Always thought the ratios were a bit strange - too big gap between 2 and 3. Maybe not the correct box? How would I identify what I've got without splitting the box?
All input greatly appreciated.
So it's high comp it would seem
pacerpete has sold me a 9.4:1 lump. (medium comp?)
How much weaker is it going to feel given that I'm sticking with my presumably Motronic 1.1 ignition.
Anyone got any thoughts about the missing gearbox code? Always thought the ratios were a bit strange - too big gap between 2 and 3. Maybe not the correct box? How would I identify what I've got without splitting the box?
All input greatly appreciated.
-
e301988325i
- E30 Zone Addict

- Posts: 3701
- Joined: Fri Feb 01, 2008 11:00 pm
- Location: Taunton, Somerset
There's a 256E1 9.75:1 and 256E2 9.4:1, yours si more likely 256E1.
Why are you changing engines, is yours worn?
see here for gearbox ID, I can't remember where on the gearbox though, more likely on the side TBH. If you've got wide ratio's 1-2-3 then it's a standard 325 box, where first is normally not necessary.
You can swap it for directly for a close ratio g/box out of a 325i sport which has higher 1-2-3 gears and is a massive improvement.
http://www.e30zone.net/modules.php?name ... arbox++hmm
Why are you changing engines, is yours worn?
see here for gearbox ID, I can't remember where on the gearbox though, more likely on the side TBH. If you've got wide ratio's 1-2-3 then it's a standard 325 box, where first is normally not necessary.
You can swap it for directly for a close ratio g/box out of a 325i sport which has higher 1-2-3 gears and is a massive improvement.
http://www.e30zone.net/modules.php?name ... arbox++hmm
I said:
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
-
Barx325i
- Engaged to the E30 Zone

- Posts: 6493
- Joined: Wed Jul 26, 2006 11:00 pm
a 320 box has the same ratios I believe?
-
gooner1
- Out humping Reindeer
- Posts: 13280
- Joined: Fri Apr 14, 2006 11:00 pm
- Location: Northampton.For my sins.
FEP wrote:25 6E
So it's high comp it would seem
pacerpete has sold me a 9.4:1 lump. (medium comp?)
How much weaker is it going to feel given that I'm sticking with my presumably Motronic 1.1 ignition.
Anyone got any thoughts about the missing gearbox code? Always thought the ratios were a bit strange - too big gap between 2 and 3. Maybe not the correct box? How would I identify what I've got without splitting the box?
All input greatly appreciated.
FEB, not sure what you have in mind for your H/C engine but i may be in need of all 6 pistons if available,

-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
^was just about to add that the 320 (G240) box has the same ratios as the 325CR (G260CR) box,
have you got any numbers on the bottom of the pistons on the bottom of the crown?
i think yours should be KS pistons but could as easily be mahle.
have you got any numbers on the bottom of the pistons on the bottom of the crown?
i think yours should be KS pistons but could as easily be mahle.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
-
Barx325i
- Engaged to the E30 Zone

- Posts: 6493
- Joined: Wed Jul 26, 2006 11:00 pm
Caution, I'm unreliable, but I have a set for salegooner1 wrote:
FEB, not sure what you have in mind for your H/C engine but i may be in need of all 6 pistons if available,
-
e301988325i
- E30 Zone Addict

- Posts: 3701
- Joined: Fri Feb 01, 2008 11:00 pm
- Location: Taunton, Somerset
If by the same you mean different. If you want the ratios and percentage gaps then search gearbox ratios against my usernameBarx325i wrote:a 320 box has the same ratios I believe?
I said:
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
i was under the impression that 1st was lower but the rest were about the same?
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
-
FEP
- E30 Zone Regular

- Posts: 309
- Joined: Sat May 24, 2008 11:00 pm
- Location: Hackney (of carriage fame) London
Sorry - should have said - it is a sport.e301988325i wrote:There's a 256E1 9.75:1 and 256E2 9.4:1, yours si more likely 256E1.
Why are you changing engines, is yours worn?
see here for gearbox ID, I can't remember where on the gearbox though, more likely on the side TBH. If you've got wide ratio's 1-2-3 then it's a standard 325 box, where first is normally not necessary.
You can swap it for directly for a close ratio g/box out of a 325i sport which has higher 1-2-3 gears and is a massive improvement.
http://www.e30zone.net/modules.php?name ... arbox++hmm
25 6E seems to be followed by a '1'.
Changing because I cooked another head(!) and decided this time engine change would be simpler and cheaper than head change, and an engine was available, but not a 'good' head.
Once it's out, we'll see what gearbox id I can find - maybe it's lost its sport gearbox and got a standard one. Not sure that I'd say that first is redundant but I guess it depends how you drive.
Anyway, gonna see how the engine feels and then if all is well and I don't like the 9.4:1 or I get upset about lack of originality, I could always bite the bullet and put the 'new' head on the old block. Gooner1 - suspect that if I decide to keep the 9.4 block, I'll want to hang on to the pistons for the sake of a future fussy owner - but then supose that depends what they're worth.
HairyScreech - pistons are still in the block so not sure about make and numbers but they certainly look like Gooner1's pictures from the tops, though thinking about it, maybe they haven't got the valve cutouts.
Pacerpete reckons I wont feel much difference going from 9.7 to 9.4. We'll see. Certainly as it was it pulled pretty well.
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
the 0.3 drop in compression will be negligible, certainly not something you could feel unless your really sensitive to cars.
best bet is to keep the block and pistons in the shed with a good layer of grease on the bores and a spare sump and knackered head to keep it all sealed up. that way should you ever want matching numbers later on then its just a block swap away.
best bet is to keep the block and pistons in the shed with a good layer of grease on the bores and a spare sump and knackered head to keep it all sealed up. that way should you ever want matching numbers later on then its just a block swap away.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
-
e301988325i
- E30 Zone Addict

- Posts: 3701
- Joined: Fri Feb 01, 2008 11:00 pm
- Location: Taunton, Somerset
mph at 6900rpm, no tyre slip factored in. as you can see the g240/320i box is the widest of all between 1st and 2nd, in my opinion 1st is still not tall enough in the c-r/sport box. to the OP, i've never been able to find if the ratios were cr in the tech1 sport.
e301988325i wrote:1st divided by 5th, the lower the number the closer the ratios of the gearbox
325i, with 3.64
1st divided by 5th = 4.73
1st- 3.83- 35.4 mph
2nd- 2.20- 61.6 mph
3rd- 1.40- 96.8 mph
4th- 1.00- 135.6 mph
5th- 0.81- 167.4 mph
325i sport with, 3.91:1 lsd
Standard tech 2 sport
1st divided by 5th = 4.14
1st- 3.35- 37.7 mph
2nd- 2.03- 62.2 mph
3rd- 1.36- 92.8 mph
4th- 1.00- 126.2 mph
5th- 0.81- 155.8 mph
sport box with 3.64
1st divided by 5th = 4.14
1st- 3.35- 40.5 mph
2nd- 2.03- 66.8 mph
3rd- 1.36- 99.7 mph
4th- 1.00- 135.6 mph
5th- 0.81- 167.4 mph
320i g240 gearbox with 3.64
1st divided by 5th = 4.59
1st- 3.72- 36.4 mph
2nd- 2.02- 67.1 mph
3rd- 1.32- 102.7 mph
4th- 1.00- 135.6 mph
5th- 0.81- 167.4 mph
262 with 3.15
1st divided by 5th = 3.7
1st- 3.72- 42.1 mph
2nd- 2.4- 65.3 mph
3rd- 1.77- 88.5 mph
4th- 1.26- 124.3 mph
5th- 1- 156.6 mph
I said:
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
i think the reason people say the 320 box is a substitute if the fact that 2nd and 3rd are very close to the sport ratio and the 4th and 5th are the same.
after all who uses 1st in normal driving?
after all who uses 1st in normal driving?
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
-
e301988325i
- E30 Zone Addict

- Posts: 3701
- Joined: Fri Feb 01, 2008 11:00 pm
- Location: Taunton, Somerset
yeah i guess once you're up and rolling they're the same. however if you're going to the effort of changing then it's got to be the sport box. one of the best upgrades after brakes and quick rack.
I said:
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
agreed, although cost comes into it a bit, g240s are super cheep, a good g260cr is getting scarce now.
OT - do you do laser cutting at your place?
OT - do you do laser cutting at your place?
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
-
FEP
- E30 Zone Regular

- Posts: 309
- Joined: Sat May 24, 2008 11:00 pm
- Location: Hackney (of carriage fame) London
e301988325i wrote: to the OP, i've never been able to find if the ratios were cr in the tech1 sport.
Well, the box will be out in the next few days. Assuming it is a genuine tech 1 box, is it possible to establish how many teeth on each cog without splitting the box?
The ratios are so odd - on a give and take back road I'm constantly looking for gear two and a half, I even wondered if someone had changed the cogs but i guess that's pretty unlikely.
-
e301988325i
- E30 Zone Addict

- Posts: 3701
- Joined: Fri Feb 01, 2008 11:00 pm
- Location: Taunton, Somerset
Possibly why the tech 2 sports came with a 3.91:1 diff, Vs yours, which would have originally had a 3.64:1.
Looking for gear 2.5 in a 2.5 is quite unusual tbh 3rd should cover all but tightest of corners, I'm normally looking for gear 3.5, but that'll be fixed with a taller (than 3.64 diff) and a 2.8L stroker to drive it!
Looking for gear 2.5 in a 2.5 is quite unusual tbh 3rd should cover all but tightest of corners, I'm normally looking for gear 3.5, but that'll be fixed with a taller (than 3.64 diff) and a 2.8L stroker to drive it!
I said:
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
-
FEP
- E30 Zone Regular

- Posts: 309
- Joined: Sat May 24, 2008 11:00 pm
- Location: Hackney (of carriage fame) London
Box is free! Number (near the clutch slave mounting) is 260 0 1346 90. What does that tell us?
-
e301988325i
- E30 Zone Addict

- Posts: 3701
- Joined: Fri Feb 01, 2008 11:00 pm
- Location: Taunton, Somerset
e301988325i wrote:see here for gearbox ID, HNN or TNM or something cast in raised lettering somewhere, detailed in this thread
http://www.e30zone.net/modules.php?name ... arbox++hmm
I said:
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
Can anyone suggest how to test if the boot lights are staying on with the boot shut?
e30topless said:
lock the wife in there
-
FEP
- E30 Zone Regular

- Posts: 309
- Joined: Sat May 24, 2008 11:00 pm
- Location: Hackney (of carriage fame) London
Found the ID - on the edge of the bellhousing front flange, bottom left looking from the back of the car.
04938 1NW
Any interpretations? The Correct Sport gearbox or not?
Car build was March '87.
Cheers
04938 1NW
Any interpretations? The Correct Sport gearbox or not?
Car build was March '87.
Cheers
-
FEP
- E30 Zone Regular

- Posts: 309
- Joined: Sat May 24, 2008 11:00 pm
- Location: Hackney (of carriage fame) London
bump
-
FEP
- E30 Zone Regular

- Posts: 309
- Joined: Sat May 24, 2008 11:00 pm
- Location: Hackney (of carriage fame) London
I've been looking at the layshaft (contershaft) info on BMW Fans.e301988325i wrote:mph at 6900rpm, no tyre slip factored in. as you can see the g240/320i box is the widest of all between 1st and 2nd, in my opinion 1st is still not tall enough in the c-r/sport box. to the OP, i've never been able to find if the ratios were cr in the tech1 sport.
Seems that from 1985 through 1991 there were 2 different layshafts for M20 325i's, one for Sport and the other for normal.
Unless I'm missing something, that would mean that there are just two ratio configurations that ran through the facelift without change. I.e., the Tech 1 had the same close ratio's as the Tech 2. BUT, did every sport have a CR box as standard or was it an option? Anyone know?
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
The 'Sport' was just a collection of pre ticked options, including the CR gearbox, so yes, it was standard. You could also have the same box on any other 325i if you ticked the right box on the list.
If you absolutely insisted, you could probably have ordered your 'Sport' with an ordinary box, and it's likely that plenty have 'lost' the CR box since the car was built.
If you absolutely insisted, you could probably have ordered your 'Sport' with an ordinary box, and it's likely that plenty have 'lost' the CR box since the car was built.
-
FEP
- E30 Zone Regular

- Posts: 309
- Joined: Sat May 24, 2008 11:00 pm
- Location: Hackney (of carriage fame) London
I don't get this - sure many cars will have succumbed to the tin worm and had their boxes 'liberated', but why would a still running sport have lost its box? I didn't have the impression that boxes are especially liable to die any more quickly than the rest of the mechanicals - or am I wrong on that?Brianmoooore wrote:If you absolutely insisted, you could probably have ordered your 'Sport' with an ordinary box, and it's likely that plenty have 'lost' the CR box since the car was built.
FEP
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
There will be plenty which have had engine failure, where the engine and box have been swapped together for the same from a non 'sport' 325.
-
FEP
- E30 Zone Regular

- Posts: 309
- Joined: Sat May 24, 2008 11:00 pm
- Location: Hackney (of carriage fame) London
Ah yes - I buy that!
