running rich, not blue temp sensor

Need technical Q/A then you're in the right place

Moderator: martauto

schnaarf
E30 Zone Camper
E30 Zone Camper
Posts: 1076
Joined: Sun Jun 24, 2007 11:00 pm

Post Thu Aug 04, 2011 10:15 am

Morning boys and girls. I know from searching that this has been covered many times but most posts point towards blue temp sensor.

I've checked the blue temp sensor at the ECU and at the sensor itself. After being parked for 5 hours (but still in hot sunshine) there was a reading of about 2000 Ohm and when up to running temp, 300 Ohm - which looks about right.

I always thought it was a bit rich but when comparing it to HongKongFueys 325i the other evening and hardly being able to smell the exhaust, I realised mine was ridiculous. Even the slightest sniff and it makes me cough. When cold there is a white steam from the exhaust but this is NOT coolant, it hasn't used a drop of water or oil in 6 months (over 6000 miles).

The engine was originally 'tuned' and 'a chip added, specially matched to the engine and ecu'. I put a standard ecu in a year ago and its serviced and tappets reset every 6 months or so.

Also the idle isn't very smooth and makes the car shudder and the exhaust is popping (not sure if that's the right word for it) although the rev needle sits dead steady. All hoses look in good order apart from the thin one on top of the engine which is a bit perished.

Seems to run rich right at all times. When the engine was 'tuned' maybe the fuel/air mixture screw was messed around with.

Apart from having the injectors cleaned and having the mixture screw altered with a gas analyser, what else to check before messing with the mixture screw?
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Thu Aug 04, 2011 10:21 am

M20? Check out under the lower rubber boot of the injector loom plug and socket, under the inlet manifold.
You'll have to take off the big air pipe for access, so check out the throttle position switch while you're at it.
schnaarf
E30 Zone Camper
E30 Zone Camper
Posts: 1076
Joined: Sun Jun 24, 2007 11:00 pm

Post Thu Aug 04, 2011 11:13 am

Circular plug quite far down? The reading of the blue temp sensor at the ecu end was ok..

I did adjust the tps a while ago, it does 'click'. Will check continuity later.
User avatar
m8782538
E30 Zone Squatter
E30 Zone Squatter
Posts: 1550
Joined: Mon Feb 07, 2011 11:00 pm
Location: Swindon

Post Thu Aug 04, 2011 11:14 am

The "popping" noise coming from the exhaust is usually unburnt fuel igniting in the exhaust system, normally only happens when its hot though, Be carefull if you have a cat in your exhaust as unburnt fuel can cause issues with it.
schnaarf
E30 Zone Camper
E30 Zone Camper
Posts: 1076
Joined: Sun Jun 24, 2007 11:00 pm

Post Thu Aug 04, 2011 11:40 am

No cat :)

I think it is worse when anything but stone cold. Thinking about it the idle is slightly less shuddery when stone cold..
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Thu Aug 04, 2011 12:36 pm

Wonder if you have an air leak around the inlet manifold/various pipes?

Un-metered air finding it's way in,ECU starts chucking more fuel in?

is that thin perished hose the one that runs from the FPR to the bracket on the inlet manifold?

Will cost pennies to replace...
Youth is wasted on the young.
User avatar
MattCyclone
E30 Zone Newbie
E30 Zone Newbie
Posts: 134
Joined: Thu May 14, 2009 11:00 pm
Location: Soton, Hampshire

Post Thu Aug 04, 2011 12:43 pm

Steve,

Do let me know how you get on, mine is rather fragrant at times too!

You manage to get the beam bushes done in the end?
schnaarf
E30 Zone Camper
E30 Zone Camper
Posts: 1076
Joined: Sun Jun 24, 2007 11:00 pm

Post Thu Aug 04, 2011 12:43 pm

daimlerman wrote:Wonder if you have an air leak around the inlet manifold/various pipes?

Un-metered air finding it's way in,ECU starts chucking more fuel in?

is that thin perished hose the one that runs from the FPR to the bracket on the inlet manifold?

Will cost pennies to replace...
The pipes all look in good condition - no sign of cracking. Will spray some wd-40 around the area tonight and see if the revs change.

It is that hose, yes. Where's a good place to find a replacement; what size is it?
User avatar
MattCyclone
E30 Zone Newbie
E30 Zone Newbie
Posts: 134
Joined: Thu May 14, 2009 11:00 pm
Location: Soton, Hampshire

Post Thu Aug 04, 2011 12:45 pm

Steve,

Just looking to replace the same hose, let me know where you find it, or buy double the length and I'll grab the other half off you... Going to try the motor factors by work here...
schnaarf
E30 Zone Camper
E30 Zone Camper
Posts: 1076
Joined: Sun Jun 24, 2007 11:00 pm

Post Thu Aug 04, 2011 12:46 pm

likewise Matt, if you find some let me know!

edit: I did get the bushes done in the end thanks Matt- ended up with an angle grinder on the aluminium bush..
User avatar
MattCyclone
E30 Zone Newbie
E30 Zone Newbie
Posts: 134
Joined: Thu May 14, 2009 11:00 pm
Location: Soton, Hampshire

Post Thu Aug 04, 2011 12:51 pm

Kimber will check on the breather, though he was not that confident... Will let you know tomorrow morning.
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Thu Aug 04, 2011 12:56 pm

Not sure of the size off-hand,but it's small!

You may get away with trimming the ends,then you will have a sample to take to your local motor factors as well.

The splined sockets where the connecters are for the servo were my last air leak point,I ran a smear of silicone around the spline to get a seal.
Youth is wasted on the young.
User avatar
wullie325i
CAUTION - unreliable trader!
Posts: 1398
Joined: Wed Jul 27, 2005 11:00 pm

Post Thu Aug 04, 2011 1:00 pm

i have had this before aswell and for me it was the afm that was at fault get one thats a known good one from someone else and try it.

had the exact same problem on an m50 and again it was a dud maf.
User avatar
wullie325i
CAUTION - unreliable trader!
Posts: 1398
Joined: Wed Jul 27, 2005 11:00 pm

Post Thu Aug 04, 2011 1:16 pm

like some have said also the plug under all the gubbins is a good place to check aswell.
schnaarf
E30 Zone Camper
E30 Zone Camper
Posts: 1076
Joined: Sun Jun 24, 2007 11:00 pm

Post Thu Aug 04, 2011 2:44 pm

Brianmoooore wrote:M20? Check out under the lower rubber boot of the injector loom plug and socket, under the inlet manifold.
You'll have to take off the big air pipe for access, so check out the throttle position switch while you're at it.
Checked the TPS - Continuity when closed with 2 pins and continuity at more than half way or so with the other pin; nothing at any other position. The same as the spare I have here.

Will check the injector loom later.
wullie325i wrote:i have had this before aswell and for me it was the afm that was at fault get one thats a known good one from someone else and try it.

had the exact same problem on an m50 and again it was a dud maf.
Is there any way of checking the afm?
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Aug 05, 2011 9:56 am

schnaarf wrote:
Is there any way of checking the afm?
6 or 9 volt battery across the outer terminals of the track, and measure the voltage on the wiper terminal as the flap is slowly moved open by hand.
Voltage must always increase, and never drop back, even for the briefest period.
This is a far more effective method than that detailed by Haynes.
schnaarf
E30 Zone Camper
E30 Zone Camper
Posts: 1076
Joined: Sun Jun 24, 2007 11:00 pm

Post Fri Aug 05, 2011 2:43 pm

Brianmoooore wrote:
schnaarf wrote:
Is there any way of checking the afm?
6 or 9 volt battery across the outer terminals of the track, and measure the voltage on the wiper terminal as the flap is slowly moved open by hand.
Voltage must always increase, and never drop back, even for the briefest period.
This is a far more effective method than that detailed by Haynes.
Brilliant, thanks. This obviously means removing the black plastic cap - it there anything I need to be super careful about?
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Aug 05, 2011 7:54 pm

Cap doesn't need removing. All three connections are in the plug.
Meter neg and battery neg. to pin 4, battery + to pin 3, and meter + to pin 2.
User avatar
MattCyclone
E30 Zone Newbie
E30 Zone Newbie
Posts: 134
Joined: Thu May 14, 2009 11:00 pm
Location: Soton, Hampshire

Post Fri Aug 05, 2011 11:01 pm

Steve,

Got some washer tubing in the end for the breather pipe, got heaps left over if you want a length?

Got a split in one of the rubber pipes, from the AFM to the injection manifold but not sure if that it is all the way through the rubber as I can't see through it...
schnaarf
E30 Zone Camper
E30 Zone Camper
Posts: 1076
Joined: Sun Jun 24, 2007 11:00 pm

Post Fri Aug 05, 2011 11:12 pm

Brian, thanks for that. Turns out the afm was ok although I've swapped it for another and the emissions seem better. The mixture screw must have been altered on the old one

Matt, I'll have a bit of that off you! Around tomorrow?
User avatar
MattCyclone
E30 Zone Newbie
E30 Zone Newbie
Posts: 134
Joined: Thu May 14, 2009 11:00 pm
Location: Soton, Hampshire

Post Sat Aug 06, 2011 8:49 am

Am in and out today, will send you a PM with my address and I will leave the tubing in the porch for you to collect.
320
E30 Zone Regular
E30 Zone Regular
Posts: 251
Joined: Sat Jan 22, 2011 11:00 pm

Post Sat Aug 06, 2011 1:47 pm

i have the same problem, iv just done a test of the blue sensor with the engine upto temp, its giving a reading of 266 is this to low?, am waiting for the engine to cool down to test it when its cold,
schnaarf
E30 Zone Camper
E30 Zone Camper
Posts: 1076
Joined: Sun Jun 24, 2007 11:00 pm

Post Sun Aug 21, 2011 10:23 am

320 wrote:i have the same problem, iv just done a test of the blue sensor with the engine upto temp, its giving a reading of 266 is this to low?, am waiting for the engine to cool down to test it when its cold,
I think those readings are ok. 2500-3000 is correct when cold, when warm it should be around that number. Basically I think that if the reading changes between cold and warm it should be ok. Did you take this reading from the ecu end?

Massively improved the emissions by swapping the afm. Using a battery and volt meter, the old one showed as working perfectly so it must have been buggered about with previously. Still maybe a bit high but the tappets need doing and probably the injectors need cleaning.
User avatar
fixedwheelnut
E30 Zone Regular
E30 Zone Regular
Posts: 909
Joined: Sun Nov 20, 2005 11:00 pm
Location: South East London

Post Sun Aug 21, 2011 11:23 am

schnaarf wrote: . Did you take this reading from the ecu end?

.
Most important bit of info here, measure it at the ECU and that will pick up any high resistance in the wiring loom, get someone to wiggle the wiring at the plug under the inlet manifold and see if the reading changes wildly.

temp degrees C--------------- Resistance ohms---------- Volts
0 ------------------------------- 5,700 - 5,900 -------------3v
20 ------------------------------2,400 - 2,600 ----------- 2.2-2.8
40 ------------------------------1,100 - 1,300 ------------1.0-1.4
80------------------------------ 300-400 ----------------- 0.6-0.8
100 -----------------------------200ohms
User avatar
Billwill
E30 Zone Regular
E30 Zone Regular
Posts: 363
Joined: Sun Jun 26, 2011 11:00 pm
Location: South Africa

Post Tue Aug 23, 2011 12:43 pm

I know on the 318i M40, if you cannot get the O2 mixture right by adjusting the potentiometer on the AFM....it could mean that someone has moved the positition of the spring inside the AFM.
You can carefully split the AFM open..mark the position of the spring base and try moving it one notch. I believe moving it clockwise weakens the mixture, anti-clockwise enrichens it.
Then glue the two halve back together with a bit of silicon sealant.

Are you sure you do not have leaking fuel injectors? :?
clipper
E30 Zone Squatter
E30 Zone Squatter
Posts: 1980
Joined: Mon Aug 22, 2005 11:00 pm
Location: Madrid

Post Tue Aug 23, 2011 2:33 pm

schnaarf wrote: Massively improved the emissions by swapping the afm. Using a battery and volt meter, the old one showed as working perfectly so it must have been buggered about with previously.
I had the same problem, and it was indeed the mixture screw on the afm, someone had wound it all the way in (presumably to try to compensate for an air leak which I resolved when I did the top end and when I put it back together it was like you describe).
A quick trip to the gas analysis machine and back to full working order in no time.

You could always try to see if you can wind in the mixture screw at all (remembering the original position), if you can't wind it in it'll be because it's been set as rich as possible.
These are sensations as hard to forget as they are to ignore.....