M20 Clutches - Difference?

Need technical Q/A then you're in the right place

Moderator: martauto

Silverfang
E30 Zone Regular
E30 Zone Regular
Posts: 937
Joined: Fri Dec 23, 2005 11:00 pm
Location: Northampton

Post Sat Jun 25, 2011 7:11 pm

As above really. I've got a good LUK clutch and lightened flywheel out of my old 2.0 2 door after i crashed it :cry:

Question is the clutch from a M20B20 identical to that of one from a M20B25? Or is the poundage of springs higher in the 2.5 version?

Just want to confirm, or I'll have to sell on the clutch (barely 3000 miles on it!) and get a new one :mad:
BMW and Opel, both RWD, both german, both good fun
http://www.clockservicing.co.uk/ For any clock repairs try here.
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Sat Jun 25, 2011 7:16 pm

Bung it on the 2.5, will be fine 8)
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Sat Jun 25, 2011 7:42 pm

Pressure plate spring is different,but I have used a 320i clutch on my 2.7 for 4 or 5 years with no problems,it must have run almost 200k by now!
Youth is wasted on the young.
User avatar
gooner1
Out humping Reindeer
Posts: 13280
Joined: Fri Apr 14, 2006 11:00 pm
Location: Northampton.For my sins.

Post Sun Nov 20, 2011 8:57 pm

I have a brand new 320i clutch that i intend to use in my
2.8 build, however i have no release bearing for it.
Do I get the 325i or the 320i one, or does it not matter :?:
Clutch is a Sachs, if that helps.
Image
e30topless
E30 Zone Team Member
E30 Zone Team Member
Posts: 13595
Joined: Wed Aug 23, 2006 11:00 pm
Location: surrounded by scrap

Post Sun Nov 20, 2011 9:16 pm

doesn't matter Rob, IIRC all M20 clutch parts are the same
Simon13
The longest resto in the world !
Posts: 22697
Joined: Mon Jan 10, 2005 11:00 pm
Location: Camberley, Surrey don't u know

Post Sun Nov 20, 2011 10:54 pm

they're all the same pressure plate and disc, the only difference is the size of the release bearings. 325's use the big one for the 260 box and 320's the little one for the 240 box
HairyScreech
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6265
Joined: Sun Jan 21, 2007 11:00 pm

Post Sun Nov 20, 2011 11:30 pm

Took a 320 clutch out of a 2.5 car I did a long time ago about 2 years back, the relese bearing had died but the rest of it was fine and went back in the shed for road car spares.

That car had a full 2.5 kit fitted complete with bearing and that was a 240 box. Relese bearings were identical
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822

m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
User avatar
gooner1
Out humping Reindeer
Posts: 13280
Joined: Fri Apr 14, 2006 11:00 pm
Location: Northampton.For my sins.

Post Mon Nov 21, 2011 8:43 am

Cheers chaps. :thumb:
Image
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Mon Nov 21, 2011 9:12 am

Part # for the release bearing is the same, part # for the clutch disc is the same, part # for the complete clutch kit is different.
Conclusion - there is a difference in the cover plate assembly, and I'm with daimlerman - the clutch pedal on a 325 is noticeably heavier than that on a 320, so I reckon the spring is stronger as well.
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Mon Nov 21, 2011 9:17 am

While we are on the subject here,

How do you change the clutch on an E30? M20 we'll go, hopefully it isnt much different from engine to engine...

This is for the Wiki by the way... :thumb:

Any advise is appreciated.
HairyScreech
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6265
Joined: Sun Jan 21, 2007 11:00 pm

Post Mon Nov 21, 2011 9:18 am

i did notice that, the car i changed it out on had a heavier pedal after the clutch swap, i just put it down to new clutch vs old 100k clutch and didn't pay it too much mind.

it would make sense that the pressure plate is stronger as the torque the clutch can transmit is proportional to the clamping force.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822

m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Mon Nov 21, 2011 9:29 am

Jim320i wrote:While we are on the subject here,

How do you change the clutch on an E30? M20 we'll go, hopefully it isnt much different from engine to engine...

This is for the Wiki by the way... :thumb:

Any advise is appreciated.
No different from any other car back when all other cars had the engine facing the correct way, and driving the correct wheels.
Jim320i
E30 Zone News / COTM Team
E30 Zone News / COTM Team
Posts: 10627
Joined: Sun Oct 25, 2009 11:00 pm
Location: Leicestershire

Post Mon Nov 21, 2011 9:32 am

Brianmoooore wrote:
Jim320i wrote:While we are on the subject here,

How do you change the clutch on an E30? M20 we'll go, hopefully it isnt much different from engine to engine...

This is for the Wiki by the way... :thumb:

Any advise is appreciated.
No different from any other car back when all other cars had the engine facing the correct way, and driving the correct wheels.
Ahh, thanks Brian, that narrows it down alot then. I found a guide for an E36 engine of some sort so we should be able to rewrite a guide from that :thumb:

Few more questions coming too but i'll start another thread shortly.