is it a big job to take the inlet manifold off?
Moderator: martauto
-
Ali786
- E30 Zone Regular

- Posts: 276
- Joined: Tue Mar 15, 2011 11:00 pm
- Location: Nottingham
is it a big job to take the inlet manifold off? can anyone help me on how to do this?
Blue 1988 320i convertible
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
Best asked in Tech Help!
Perhaps a friendly moderator will move this for you.
Briefly;
Remove airbox
Dis-connect throttle cable
Unbolt manifold
Push down crankcase breather tube(under manifold)
Slide manifold off studs
May be nessesary to remove thermostat housing at the same time
This is for M20 engine,BTW.
Going back is reverse of above,BUT,compress breather tube spring with a couple of cableties,when manifold is fitted,cut ties and locate the top of the tube correctly,fit new O rings to this tube.
Perhaps a friendly moderator will move this for you.
Briefly;
Remove airbox
Dis-connect throttle cable
Unbolt manifold
Push down crankcase breather tube(under manifold)
Slide manifold off studs
May be nessesary to remove thermostat housing at the same time
This is for M20 engine,BTW.
Going back is reverse of above,BUT,compress breather tube spring with a couple of cableties,when manifold is fitted,cut ties and locate the top of the tube correctly,fit new O rings to this tube.
Youth is wasted on the young.
-
Jim320i
- E30 Zone News / COTM Team

- Posts: 10627
- Joined: Sun Oct 25, 2009 11:00 pm
- Location: Leicestershire
Also want to ad to Malcs list... Its a pain in the arse. I didnt do with with cable tieing the breather tube, one of the most stressfull things try to get that back in.
-
sunnyr83
- E30 Zone Addict

- Posts: 2286
- Joined: Fri Jun 05, 2009 11:00 pm
- Location: West London 'init'
^agreed with the breather hose, pain in the arse before i found an easy route but can't remember it... 
-
e30-EVN
- Old Skooler

- Posts: 3382
- Joined: Sun Dec 13, 2009 11:00 pm
- Location: S.Wales
Haha, Cable ties FTW lads 
A 2 door e30 with 8 cylinders, what could be better

-
Green
- E30 Zone Squatter

- Posts: 1698
- Joined: Wed Mar 17, 2010 11:00 pm
- Location: Santa Pod
I removed it and it wasn't a too bad job tbh. Bit fiddly getting all the nuts off and back on but that was about it. Breather tube was easy i just pushed it through underneath and popped it on again.
What you taking the manifold off for?
What you taking the manifold off for?

-
Ajsingh
- E30 Zone Addict

- Posts: 2378
- Joined: Sun Mar 28, 2010 11:00 pm
- Location: West Laaaandaan init! / Milton Keynes
It was quite easy.. I removed and re fitted mine last week.. No need to touch the thermostat housing but u will need to remove the pipe that does into te bottle of the housing and it runs along the block. It is quite simple, crack the nuts off and loosen them free by hand.. Careful of the washers that are with the nuts and that big black tube that runs straight down the middle has 2 seals either side of it.. Make sure they are in good condition and not ripped...
E30 Crazy!
-
Morat
- E30 Zone Team Member

- Posts: 8943
- Joined: Thu Feb 09, 2006 11:00 pm
- Location: The Peoples Republic of Yorkshire
Moved to tech help.
E30 Touring 0.35 cD - more slippery than prison soap 

Praise the Lard... and pass the dripping!

Praise the Lard... and pass the dripping!
-
kman82
- E30 Zone Regular

- Posts: 967
- Joined: Mon Sep 22, 2008 11:00 pm
- Location: Oxford
I'm half way through this job, so far got half the bolts off but I've stopped when i've realised there is a hose running vertically from the centre of the inlet manifold down to the bottom of the engine. BMW mentioned 'water hose' when I was ordering the new gaskets, Is that right? When i take the manifold off is coolant going to p1ss out everywhere?
-
Ajsingh
- E30 Zone Addict

- Posts: 2378
- Joined: Sun Mar 28, 2010 11:00 pm
- Location: West Laaaandaan init! / Milton Keynes
No, that is an oil drain from the head to the sump... Grip with both hands and pull down.... There is a runber seal in the inlet and one on the sump. Keep an eye out for them
E30 Crazy!
-
kman82
- E30 Zone Regular

- Posts: 967
- Joined: Mon Sep 22, 2008 11:00 pm
- Location: Oxford
pull down with the inlet manifold still in place?
I guess I should get a new rubber seal ordered
I guess I should get a new rubber seal ordered
-
B7
- E30 Zone Team Member

- Posts: 15841
- Joined: Tue Feb 13, 2007 11:00 pm
- Location: Surrey / West Sussex
Come on! It's hardly a taxuing job is it? Try an M20 starter motor............
B7's Motto. "If it's French, BURN IT!!!!!!"
-
FEP
- E30 Zone Regular

- Posts: 309
- Joined: Sat May 24, 2008 11:00 pm
- Location: Hackney (of carriage fame) London
Don't know if it was just me, but some of the nuts are 12mm and some are 13. Definately need some thin walled sockets.
-
kman82
- E30 Zone Regular

- Posts: 967
- Joined: Mon Sep 22, 2008 11:00 pm
- Location: Oxford
Starter motor is on its last legs!!B7 wrote:Come on! It's hardly a taxuing job is it? Try an M20 starter motor............
-
Kedge
- Old Skooler

- Posts: 7698
- Joined: Thu Jan 13, 2005 11:00 pm
- Location: Leicestershire
This is an easy enough job, i find it much harder putting cable ties on the spring, just line it all up and then give the pipe a good push down into the sump, usually sticks for a few seconds for the inlet to slide on fully.
Would've thought it best to change the starter while the inlet is out the way!
Would've thought it best to change the starter while the inlet is out the way!
-
kman82
- E30 Zone Regular

- Posts: 967
- Joined: Mon Sep 22, 2008 11:00 pm
- Location: Oxford
Sorry to drag this out, is the oil breather pipe in question 11 here?
http://www.realoem.com/bmw/showparts.do ... g=11&fg=10
no o ring on the top?
I might think about doing the starter motor at the same time then if access is a lot easier, B7 just wait for my daft questions then!
http://www.realoem.com/bmw/showparts.do ... g=11&fg=10
no o ring on the top?
I might think about doing the starter motor at the same time then if access is a lot easier, B7 just wait for my daft questions then!
-
Ajsingh
- E30 Zone Addict

- Posts: 2378
- Joined: Sun Mar 28, 2010 11:00 pm
- Location: West Laaaandaan init! / Milton Keynes
Yeah its number 11.. The o ring that sits on top is in a grrove in the inlet manifold... The seals should be ok to re use. Mine were ok to re use and have no oil leak
Not to worry about dragging it out, the zone is here to help others!
Not to worry about dragging it out, the zone is here to help others!
E30 Crazy!
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
I certainly wouldn't recommend reusing twenty year old O rings!
If the pipe "sticks down for a few seconds" when you push it down, then the O rings aren't lubricated properly!
If the pipe "sticks down for a few seconds" when you push it down, then the O rings aren't lubricated properly!
-
B7
- E30 Zone Team Member

- Posts: 15841
- Joined: Tue Feb 13, 2007 11:00 pm
- Location: Surrey / West Sussex
Not for the sake of about 50 pence I agree. If the nuts holding it to the head are a mix of 12's and 13's, someones been there before.Brianmoooore wrote:I certainly wouldn't recommend reusing twenty year old O rings!
!
B7's Motto. "If it's French, BURN IT!!!!!!"
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
I think the 12mm nuts are a BMW 'special',an M8 (13mm) is the same thread but the proximity of the runners makes 13mm nuts playfull to fit.I have M8 stainless self locking nuts on my manifold,and a thin 13mm three eight socket!
In the link above that Kman82 posted,the upper O ring will be shown in the manifold piccie....
In the link above that Kman82 posted,the upper O ring will be shown in the manifold piccie....
Youth is wasted on the young.
-
Kedge
- Old Skooler

- Posts: 7698
- Joined: Thu Jan 13, 2005 11:00 pm
- Location: Leicestershire
That was a tip on how to do it i picked up from the guide i used when doing my first inlet about 5 years ago and I was using brand new O-rings from BMW and a new spring. Like i said, it only stays down just long enough if you've already got the manifold lined up to just slide on the last bit.Brianmoooore wrote:I certainly wouldn't recommend reusing twenty year old O rings!
If the pipe "sticks down for a few seconds" when you push it down, then the O rings aren't lubricated properly!
-
kman82
- E30 Zone Regular

- Posts: 967
- Joined: Mon Sep 22, 2008 11:00 pm
- Location: Oxford
I've managed to get the inlet mani off ok once i found the last of the bolts. Problem now is that it dumped half the crud around the mani down into the cylinders like so...


Any good tips on how to get this sh1t out?
Also had a look at getting the starter motor out. Is there just two bolts with nuts holding it on? If so i think i'm laughing as i have good access to both.


Any good tips on how to get this sh1t out?
Also had a look at getting the starter motor out. Is there just two bolts with nuts holding it on? If so i think i'm laughing as i have good access to both.
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
Wait until the owner of your household vacumn cleaner goes shopping,then use that to suck the loose bits out.Do take great care to remove all evidence from the vacumn,though!
Starter is just the wiring connections and the two bolts that you have found.
Starter is just the wiring connections and the two bolts that you have found.
Youth is wasted on the young.
-
James90
- E30 Zone Regular

- Posts: 271
- Joined: Thu Sep 23, 2010 11:00 pm
- Location: Nottingham
I'm about to try this too to improve access to a thermostat housing stud that has snapped off.
to clear things up:
I need to push downwards on the breather pipe before i try to slide it off the studs? so does the pipe stay in the sump or does the pipe come out separately?
Can someone explain about the cable tie idea?
Thanks
to clear things up:
I need to push downwards on the breather pipe before i try to slide it off the studs? so does the pipe stay in the sump or does the pipe come out separately?
Can someone explain about the cable tie idea?
Thanks
'88 325i Auto Chromie Cabriolet in Alpine White
-
Kedge
- Old Skooler

- Posts: 7698
- Joined: Thu Jan 13, 2005 11:00 pm
- Location: Leicestershire
You should be able to get the inlet off without doing to the breather pipe, just lift and pull the inlet.
Cable tie idea is to compress the spring so the pipe sits lower for when you refit the inlet, then chop the ties off and the pipe comes back up and then just needs securing correctly to the under side of the manifold.
Cable tie idea is to compress the spring so the pipe sits lower for when you refit the inlet, then chop the ties off and the pipe comes back up and then just needs securing correctly to the under side of the manifold.
-
James90
- E30 Zone Regular

- Posts: 271
- Joined: Thu Sep 23, 2010 11:00 pm
- Location: Nottingham
So if I leave the pipe be I don't need to mess about with anything?
I can't picture it but I guess I'd know if I saw it - though if I can avoid it I will!
I can't picture it but I guess I'd know if I saw it - though if I can avoid it I will!
'88 325i Auto Chromie Cabriolet in Alpine White
-
kman82
- E30 Zone Regular

- Posts: 967
- Joined: Mon Sep 22, 2008 11:00 pm
- Location: Oxford
It was pretty easy in the end mate, you need to push the breather pipe down to separate it from the inlet before it will come off the studs. You can then remove the pipe, spring, washers and o rings all together.
The cable ties will be for refitting the inlet but I havnt got that far yet. Good luck!
The cable ties will be for refitting the inlet but I havnt got that far yet. Good luck!
-
James90
- E30 Zone Regular

- Posts: 271
- Joined: Thu Sep 23, 2010 11:00 pm
- Location: Nottingham
Ok thanks, will have a go at taking it off if I get chance this weekend.
'88 325i Auto Chromie Cabriolet in Alpine White
-
kman82
- E30 Zone Regular

- Posts: 967
- Joined: Mon Sep 22, 2008 11:00 pm
- Location: Oxford
I've had a bit of a vacume leak since i took my inlet mani off and put it back together. I had chance to look into it today and with spraying quick start under the throttle body the revs pick up a bit. After taking the throttle bottle off I noticed a big crack in the the little rubber plug on one of the spare tubes of the throttle body so have ordered a new one from bmw.
After inspecting the breather tube though i noticed oil leaking down the back of it. Is this common? I've made sure the rubber o ring is in place properly at the top and re-sited it but should this be pretty leak proof? I am now wondering if air could be drawn into the system here and causing some of the vacume leak?
I never replaced the spring of the breather tube and now wish i had so it held the tube more tightly against the mani! I think i will have to take the mani back off to change the spring!
Edit: to cut a long storey short, could enough air get into the system through a poor sealing breather pipe to cause a vacume leak?
After inspecting the breather tube though i noticed oil leaking down the back of it. Is this common? I've made sure the rubber o ring is in place properly at the top and re-sited it but should this be pretty leak proof? I am now wondering if air could be drawn into the system here and causing some of the vacume leak?
I never replaced the spring of the breather tube and now wish i had so it held the tube more tightly against the mani! I think i will have to take the mani back off to change the spring!
Edit: to cut a long storey short, could enough air get into the system through a poor sealing breather pipe to cause a vacume leak?
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
If oil is coming out, then air can get in!
-
James90
- E30 Zone Regular

- Posts: 271
- Joined: Thu Sep 23, 2010 11:00 pm
- Location: Nottingham
I did this but I would not recommend the cable tie trick! If you can't get the manifold back on without using them get an assistant to hold the tube down while you place the manifold on.
I used the smallest cable ties I could find and it was very tight getting the spring over the pipe to the point that the cable ties are in too tight to be pulled out - I'm gonna have to get the blow torch on them!
I used the smallest cable ties I could find and it was very tight getting the spring over the pipe to the point that the cable ties are in too tight to be pulled out - I'm gonna have to get the blow torch on them!
'88 325i Auto Chromie Cabriolet in Alpine White
-
kman82
- E30 Zone Regular

- Posts: 967
- Joined: Mon Sep 22, 2008 11:00 pm
- Location: Oxford
this is doing my head in! I've changed the tb plug and got it all back together AGAIN and there's still an airleak and its still leaking oil.
Sorry to be a pain brian but when you last refitted one, did you put the washer onto the breather pipe first and then the o ring over the top, then release the spring or did you try and sit the o ring into the underside of the manifold?
i cant see how it can make much difference but i must be doing something wrong for it to leak.
other than taking the manifold off to put a new spring on what else can i do!
Sorry to be a pain brian but when you last refitted one, did you put the washer onto the breather pipe first and then the o ring over the top, then release the spring or did you try and sit the o ring into the underside of the manifold?
i cant see how it can make much difference but i must be doing something wrong for it to leak.
other than taking the manifold off to put a new spring on what else can i do!
-
James90
- E30 Zone Regular

- Posts: 271
- Joined: Thu Sep 23, 2010 11:00 pm
- Location: Nottingham
There is meant to be an o-ring on the pipe at both ends. The one on the top of the pipe sits in a cut out the manifold for it when the pipe is in place
'88 325i Auto Chromie Cabriolet in Alpine White
-
kman82
- E30 Zone Regular

- Posts: 967
- Joined: Mon Sep 22, 2008 11:00 pm
- Location: Oxford
yeah got o-rings at both ends, not too worried about the bottom end coz it doesn't leak.
sorry i'm asking such spasticated questions but would you put the oring into the groove of the manifold or over the pipe before it all goes together.
sorry i'm asking such spasticated questions but would you put the oring into the groove of the manifold or over the pipe before it all goes together.
-
James90
- E30 Zone Regular

- Posts: 271
- Joined: Thu Sep 23, 2010 11:00 pm
- Location: Nottingham
If you put it over the pipe it should sit in the groove in the manifold when the pipe is in the right place.
Are you using a new spring?
Are you sure the manifold is on square? look at the part at the back where it has the vacuum pipe from the FPR, mine wanted to sit wonky where those two bolts are bolted through the bracket.
Are you using a new spring?
Are you sure the manifold is on square? look at the part at the back where it has the vacuum pipe from the FPR, mine wanted to sit wonky where those two bolts are bolted through the bracket.
'88 325i Auto Chromie Cabriolet in Alpine White

