my more door 325i

Show off your pride and joy here

Moderator: martauto

bellgtti
E30 Zone Newbie
E30 Zone Newbie
Posts: 141
Joined: Wed Jan 25, 2006 11:00 pm
Location: wolverhampton

Post Wed Dec 01, 2010 5:13 pm

i await a good discussion on wheels chice but take into account they were cheap and for winter and skiddy fun. car is mainly drift inspired and thats just what its used for aswell as daily driving, cheers in advance for looking.also apologys in advance if it the write up doesnt make sense its from a local forum i write for so things have to be broken down for the smaller minded :cool:


its been a long time coming but i feel i must let you all know what i have been upto.
began the year badly i wrote off the sierra i had bought to drift in an incident at wheels raceway, then griffo morgan and my self bought a v6 manual granada first time out it sheared the diff.

Image

Image


next time out it put the crank through the sump so it ended like the sierra on the scrap pile.
anyway cut a long story short about work etc, morgan and i stumbled accross this e30 325i on the bay, a quick phonecall found out a few more bits and revealed the seller as being an honest enough bloke all be it that he wouldnt end early doh! so whilst on holiday in newquay with the ade of an ipad (cheers sue) and morgan doing the bidding on his home comp i won the car (to the annoyance of the seller it only just met the reserve)
pics on the way home from luton

Image

Image

so got it home thrapped about for a week getting used to it and discovered a few things wrong as you do, car cut out on me and suspected fuel starvation led me to pull the pump change the filters etc

Image

filter looks about as old as the car

pump filter looked lovely and clean

Image

after

Image

next to do was remove this

Image

ive replaced it with a sparco wheel i had from my 200 a while back, the wheel is for sale if anyone fancys it???? 10 pound

then the finally problem, the previous owner had said the disks etc had only done one tour of the ring with about 10 laps the year before, i will never put these disks or pads on my car anyway but this is pretty horrific if the useage is true

Image

Image

changed to these not the best but at least it stops now without making me feel sick

Image

then had this happen to the exhaust lol oops

Image

changed that out for a stock part much better no pics whilst with josh down the garage it had a new gearbox prop mount so now my prop doesnt want to enter the car at whatever rpm its spinning at.

Image

mate sharkys jag and the beemer at the garage

now the good bits, i needed to make the bbs on the car redundant and drift wheels only so i started hunting out a set of reasonable priced sized and widthed wheels, whilst scoping the small ad's on edition it threw these up

Image

16x7j et40, the et was proper weak but i thought meh spacer will see it right so bought these

Image

did some tests

Image

Image

tried one of my 15x10.5j on the back... think there a bit o.t.t

Image

happy that the wheels were gonna fit i ordered the tyres, whilst i waited for them the car went to my mate mat's unit and had its diff mig'd up, mat bleeds vauxhall so it muct pain him having this much german attitude sitting outside his unit (2 x e30's an e36 and an e12 haha although off shot is his senny)

Image

Image

tyres arrived got fitted and the wheels were ready

Image

Image

Image

Image

Image

took it for a test run 3 up to star city saturday and it rubbed like a mother fucker so sunday morning after making the brekkie and persuading the misses to give me a hand we ghetto rolled the arches

first you load the boot with as much heavy **** as you can

Image

then heat em

Image

then you use a jack handle or something of similar diameter and stick it in the arch (between tyre and arch) whilst one controls the pole the other reverses backwards and forwards until the arches are rolled to desired spec
they dont rub now unless it has 10+ wheels in it and under heavy acceleration

there you go one write up i shall add to it whenever

parting shot cheers for the sticker bryce

Image
User avatar
toby
E30 Zone Addict
E30 Zone Addict
Posts: 3609
Joined: Thu Aug 11, 2005 11:00 pm
Location: Kent

Post Wed Dec 15, 2010 11:54 pm

Arch rollering
Image
Kemix
E30 Zone Camper
E30 Zone Camper
Posts: 1423
Joined: Tue Jul 04, 2006 11:00 pm
Location: Braintree

Post Thu Dec 16, 2010 12:11 am

Did the paint on the arches not crack at all? How long did it take to roll them?
.

Image
tonybtonyb
E30 Zone Addict
E30 Zone Addict
Posts: 3580
Joined: Wed Jun 13, 2007 11:00 pm
Location: essex

Post Thu Dec 16, 2010 12:33 am

Looking good :cool: :cool:
They don't make bm's like this anymore!..They should.
Image
suchy
True Zone Relic
Posts: 6604
Joined: Tue Apr 26, 2005 11:00 pm
Location: Portsmouth

Post Thu Dec 16, 2010 9:08 am

Haha ghetto spec arches :D
bellgtti
E30 Zone Newbie
E30 Zone Newbie
Posts: 141
Joined: Wed Jan 25, 2006 11:00 pm
Location: wolverhampton

Post Sun Feb 20, 2011 12:26 pm

hi guys long time since i posted on this thread its had a few changes.
answers on the arch rollering it takes about 10 mins a side but keeping them walm and moving the car slowly helps, depending on condition of paint will obviously have a knock on effect to the finished result. its the thrid car ive ghetto arched the first being a complete cock up but i susspose getting 17x10 et 15 onto an e36 was always going to present problems.

right back to the car, i ordered a seat rail from massive brakes a complete faff ensued with customs the weather and delivery times, took 2 months to get delivered but it arrived and my seat is fitted
Image

i also got offered a 6 branch and full exhaust system from a mate, the centre box was completely knackered but had it lopped out and now have straight through pipes which isnt to displeasing on the ear.
six branch fitted.

Image

and the finally, the wheels have been sold to my sister for her rice rocket due to a misfortune on her behalf lead to one very smashed wheel meaning i could sell the rotas and get my new wheels.
Image

but im rolling on the stock bbs due to crap weather and the fact that the car comes off the road next weekend for its heart transplant finally got my hands on an m50 all be it single vanos aswell as an e36 rack conversion and other things like e30 wieght loss.
now who do i need to speak to about m20 to m50 loom conversions and does anyone do the powersteering pipes for the e36 rack?
e30topless
E30 Zone Team Member
E30 Zone Team Member
Posts: 13595
Joined: Wed Aug 23, 2006 11:00 pm
Location: surrounded by scrap

Post Sun Feb 20, 2011 12:31 pm

Danthe can sort your looms and steering out ,

he may also give you a few tips on Arch rollering and welded diffs :D
bellgtti
E30 Zone Newbie
E30 Zone Newbie
Posts: 141
Joined: Wed Jan 25, 2006 11:00 pm
Location: wolverhampton

Post Sun Feb 20, 2011 12:34 pm

cheers for that bud shall drop him a pm shortly then, beauty is hes only in staffs so not a million miles away.
and the diff is welded and the arches are already rolled ;)