My past 2 days

Show off your pride and joy here

Moderator: martauto

stup86
E30 Zone Regular
E30 Zone Regular
Posts: 485
Joined: Mon Oct 05, 2009 11:00 pm
Location: Clevedon, Near Bristol

Post Thu Jun 10, 2010 4:24 pm

Yesterday whilst at the workshop I got busy making a simple bracket (x2):

Image
Image

Can you guess what it's for???











Maybe this can help, I took delivery of the calipers today:

Image

It's a start, just need some discs, new pads and clean the calipers up. Although with the extra 10hp I get from red calipers I may keep them!

What you think?

Cheers

Stu
Parts needed:

M40/M20 ignition coil with high voltage lead
User avatar
stixe30
E30 Zone Newbie
E30 Zone Newbie
Posts: 9
Joined: Mon Jun 07, 2010 11:00 pm

Post Thu Jun 10, 2010 5:56 pm

those calipers look bigger than my forearm!
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Thu Jun 10, 2010 5:58 pm

Is that going to sit on the disk right? What size/thickness disks will you use?

Should give a nice pedal :D
oakey
E30 Zone Addict
E30 Zone Addict
Posts: 4891
Joined: Fri Feb 10, 2006 11:00 pm
Location: Surrey

Post Thu Jun 10, 2010 5:59 pm

Are these the rx7 calipers? I remember reading the thread in e30 chat about the conversion. What size wheels will you need to run for clearance?
Image
stup86
E30 Zone Regular
E30 Zone Regular
Posts: 485
Joined: Mon Oct 05, 2009 11:00 pm
Location: Clevedon, Near Bristol

Post Thu Jun 10, 2010 6:19 pm

Yes they are RX7 calipers

I'll be using VW Corrado 280x22mm discs and a 3mm spacer so the wheel clears the caliper. The discs should sit perfectly central. I modified the design of the brackets so I may still need to 'step' the centre holes for the disk to sit central. Soon tell once I get the discs

They should fit under standard 15" BBS.

I've been writing a how-to of what is needed and i'll upload it once it's finished.

My plan is to use a E32(?) 750 master cylinder with it too.
Parts needed:

M40/M20 ignition coil with high voltage lead
stup86
E30 Zone Regular
E30 Zone Regular
Posts: 485
Joined: Mon Oct 05, 2009 11:00 pm
Location: Clevedon, Near Bristol

Post Thu Jun 10, 2010 9:13 pm

Is buying a used master cylinder a good idea or should I get a new one?
Parts needed:

M40/M20 ignition coil with high voltage lead
inlovewithRWD
E30 Zone Regular
E30 Zone Regular
Posts: 594
Joined: Wed Jul 22, 2009 11:00 pm
Location: Tunbridge Wells

Post Fri Jun 11, 2010 12:24 am

stup86 wrote:Is buying a used master cylinder a good idea or should I get a new one?
For what it's worth I'd get a new one. You don't want to take a risk when it comes to brakes.
gcs325i
E30 Zone Regular
E30 Zone Regular
Posts: 693
Joined: Fri Jul 14, 2006 11:00 pm
Location: dundee

Post Fri Jun 11, 2010 12:33 am

You may have to offset the caliper holes 2mm from the center of the strut hole's to make it work, also 15" bbs's will require a 12-15mm spacer to clear the inside of the wheel. I used a m3 M/C and the pedal is fine.