318is bosal exhaust problem ?

General E30 related discussions -
Please put technical questions in E30 Tech Help forum below

Moderator: martauto

polsta
Married to the E30 Zone
Married to the E30 Zone
Posts: 10322
Joined: Fri Oct 09, 2009 11:00 pm
Location: portsmouth

Post Tue Apr 27, 2010 4:22 pm

Whats the thoughts on this...

bought a bosal exhaust last week rear section, £140 plus £25 for a fitting kit new brackets etc

had it fitted another £20 (total £185) , and he had a bit of a nightmare getting the new rubbers on etc, weh fitted he said hmmmm this isnt the best fit and being a bosal im suprised its not the best, started it up and it was a bit blowey around the join, he said well i dont like to use it as its supposed to be a dry join, but put a bit of paste round it

its been ok, but started to blow again yesterday, and today sounds a bit blowey, so i popped back to where it was fitted, he said im flat out today but can look tomorrow, il sort it for ya but really you shud try n get back on to where you got it,s ee what they say as the fit wasnt the best as i said

so popped back to the motor factors, he said he can swap it for another one to go back ring em with the number from reciept as i didnt take it, which would mean me going to place i had fitted...getting them to take it off, taking it back quick and swapping it over

but just rang em, its not showing they have any more stock from bosal (they had to order mine in), and hes just gonna do some ringing about and ring me back, i asked what about a refund if not..he said well that might be a problem because its been fitted and used


what should i do ? bmw said £180 for one, im starting to think i should of just bought that, but surely bosal should be a goodun ?

as its a shifty fit...something you can only tell once its actualy fitted and drove, that im in my rights for a refund and to go to bmw for one ?

or...should i just see what they can do to get it sealed properly, or should i be like no f**k that i want one that fits properly on the dry join how its supposed to ? ...as i dont want more probs again after a while if they tried that ?

im a bit cheesed off to say the least :-x
Alex
Married to the E30 Zone
Married to the E30 Zone
Posts: 22665
Joined: Fri Feb 11, 2005 11:00 pm
Location: Johannesburg, South Africa

Post Tue Apr 27, 2010 4:29 pm

the bosal one is the center and rear section all in one, the bmw one is in two pieces and iirc the rear is about £180 and center bit abit cheaper, but still over £100

Hope that helps :D
polsta
Married to the E30 Zone
Married to the E30 Zone
Posts: 10322
Joined: Fri Oct 09, 2009 11:00 pm
Location: portsmouth

Post Tue Apr 27, 2010 4:33 pm

crikey....so id have to fork out £300 odd from bmw ??? 8O

what do you think i should do, sounds like they might have a prob getting another bosal one in at the moment to swap it over , it drives ok but you can hear the blowing a little bit, more so when itson idle and the window is open or drivers door and your sat there
Alex
Married to the E30 Zone
Married to the E30 Zone
Posts: 22665
Joined: Fri Feb 11, 2005 11:00 pm
Location: Johannesburg, South Africa

Post Tue Apr 27, 2010 5:03 pm

i think i worked it out around that figure yes, is it clamped on properly?

i need to make some adjustments to my bosal system as its not on straight, i was rushing to fit it
polsta
Married to the E30 Zone
Married to the E30 Zone
Posts: 10322
Joined: Fri Oct 09, 2009 11:00 pm
Location: portsmouth

Post Tue Apr 27, 2010 5:10 pm

yes i think so,but gonna take it back tomorrow and get him to check it all, take it off and put it back on again, any advice on this or what to double check ?

the motor factors just rang back, said hes rang around everywhere and cant get hold of another one, said bosal might not even be making any more ? ..i find hard to belive , reckon hes just trying a fast one to save themselves the aggro ?

im thinking even maybe i could get my original bmw one, welded up a bit, paint with heat proof paint and put that back on and just get a full refund and wait till i have £300 spare for a bmw one, if it doesnt fit proepr tomorrow and all come ok

after all the work,money,and hrs ive put in the car in the last 2 weeks, i didnt need this :-x
Alex
Married to the E30 Zone
Married to the E30 Zone
Posts: 22665
Joined: Fri Feb 11, 2005 11:00 pm
Location: Johannesburg, South Africa

Post Tue Apr 27, 2010 5:12 pm

the 318is exhaust is a pain in the arse to get hold off

i got mine on ebay there was a company selling bosal systems for £150 :)
inlovewithRWD
E30 Zone Regular
E30 Zone Regular
Posts: 594
Joined: Wed Jul 22, 2009 11:00 pm
Location: Tunbridge Wells

Post Tue Apr 27, 2010 9:43 pm

jaistanley
E30 Zone Addict
E30 Zone Addict
Posts: 2517
Joined: Tue Jan 18, 2005 11:00 pm
Location: Coventry and Essex

Post Tue Apr 27, 2010 9:58 pm

Make sure it's not fitted with those horrible U clamps, but with a decent quality strap type clamp instead. The U clamps ju=st deform the pipe and cause it to blow when over tightened...

Apart from that a decent exhaust cement and clamp should have it sealing ok, you can get away with quite a bit usually. The exhaust paste that is dark grey is usually a lot better than the stuff that dries light grey and is chalky.

HTH

Jai
Image
magpie
Old Skooler
Old Skooler
Posts: 28035
Joined: Sun Jun 29, 2008 11:00 pm
Location: Consett,Durham.

Post Tue Apr 27, 2010 10:03 pm

get that t-ossa zaust fitter to get the job done properly,i bet there's nowt wrong with the pipe and the only problem here is the coont the fitted it.
Image
m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds :)
magpie
Old Skooler
Old Skooler
Posts: 28035
Joined: Sun Jun 29, 2008 11:00 pm
Location: Consett,Durham.

Post Tue Apr 27, 2010 11:14 pm

i refitted my 8 mth old one today with no problems or exhaust paste.i bet he done one of the front bolts right up tight and then the other side one causing a blow then he never bothered to loosen them and re tighten by doing half a side at a time instead he just filled the joint with cake mix because you've already paid up and he can't be arsed to do it again properly.
Image
m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds :)
DavieP
E30 Zone Regular
E30 Zone Regular
Posts: 731
Joined: Wed Aug 01, 2007 11:00 pm
Location: South Devon

Post Wed Apr 28, 2010 5:56 am

inlovewithRWD wrote:Have you tried this website?

http://www.leisureshack.co.uk/318iS-1-8 ... 11109.aspx
These people are really quite good if you phone to make are they send the correct Bosal part. I bought an M20 exhaust centre section from them several weeks ago, via the website. It said Bosal, made no mention of any other make, so I presumed I would get Bosal.

It arrived the following day (fookin' quick and only £6 something carriage charge too!), but I was disappointed to find a Walker part, which was unacceptable. I gave them some stick over the phone and they sent out the correct Bosal resonator, picking up the Walker at the same time.

Bosal is a very good make - maybe not quite as good as the original BMW, but as near as dammit and the tone is spot-on. It's worth persevering with - get that 'fitter' to do it correctly.
Dave in Torquay

Image
polsta
Married to the E30 Zone
Married to the E30 Zone
Posts: 10322
Joined: Fri Oct 09, 2009 11:00 pm
Location: portsmouth

Post Wed Apr 28, 2010 12:36 pm

cheers lads, im jusst going back there to see him this arvo and get the car on the ramp

hes not a coont hes a mate ive known years, when he fitted it he did it up properly, i was there watching and chatting, and after it was blowing when he started, he un done it and did it again-still blowing,..that was when he said looks like your gonna have to have some paste on it-which i dont like using-then did it the 3rd time, the paste was the dark grey stuff in a tube gun thing, professional garage , il see what he says today, realy hope it sorts out
polsta
Married to the E30 Zone
Married to the E30 Zone
Posts: 10322
Joined: Fri Oct 09, 2009 11:00 pm
Location: portsmouth

Post Wed Apr 28, 2010 3:56 pm

right took the car back today, told him theyd exchange it but couldnt get another one in,he found strange...then rang round his suppliers, about 3 of them, and even euro parts, who all said the same thing...that theres none in stock anywhere and bosal themselves dont have any, so i wasnt being lied to, said it looks like i was very lucky to get that one, so lets get it sorted

put it up on the ramp, and un done it n had a look, ...he said well lets try it with different bolts...took the original 2 bolts with the springs off, put 2 smaller bolts on, and it sorted it :D , sounds sweet and happy days


is it fine like that to have it with different bolts without the springs on ? is yours like that magpie ? ..just thought id check to be safe
magpie
Old Skooler
Old Skooler
Posts: 28035
Joined: Sun Jun 29, 2008 11:00 pm
Location: Consett,Durham.

Post Wed Apr 28, 2010 6:13 pm

mine has the springs and the bolts are not threaded all the way down so there is a gap between the two flanges when tightened right up but no blowing.at least the problems sorted now and the bolts are as tight as will allow so it wont fall of.i had my new straps welded before i fitted them as they were only spot welded very lightly where the rubber goes on and didn't look like they would hold up for 20 mile 8O they were about half bmw price.
Image
m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds :)
polsta
Married to the E30 Zone
Married to the E30 Zone
Posts: 10322
Joined: Fri Oct 09, 2009 11:00 pm
Location: portsmouth

Post Wed Apr 28, 2010 8:18 pm

ok mate cheers, the origin bolts look as new not threadeded all the way down, but they wernt pulling the join quite tight enough, is it perfectly fine to have it without them springs ? or should i persist with it in trying to sort it with them ? and any ideas how to go about it ?
magpie
Old Skooler
Old Skooler
Posts: 28035
Joined: Sun Jun 29, 2008 11:00 pm
Location: Consett,Durham.

Post Wed Apr 28, 2010 8:26 pm

i'd say it's fixed now,no springs wont hurt it :)
Image
m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds :)
polsta
Married to the E30 Zone
Married to the E30 Zone
Posts: 10322
Joined: Fri Oct 09, 2009 11:00 pm
Location: portsmouth

Post Wed Apr 28, 2010 8:33 pm

good stuff, fitted a new rubber boot ait thing on the engine earlier too, other one had cracks, finally now i can drive how i want to be driving and have a right old drive :mad:

just 1 of the rear floorpan bungs to do now, do you have any idea id its 158ml ? there was 105,144,158ml ... bmw not been much help with this, cple of em in there didnt have a chuffling clue

so had a measure up, 158 i think, gotta wait 4-7 days for that and the bolts etc to come from germany, then happy days, mot next month !
magpie
Old Skooler
Old Skooler
Posts: 28035
Joined: Sun Jun 29, 2008 11:00 pm
Location: Consett,Durham.

Post Wed Apr 28, 2010 8:41 pm

i've never needed a floor bung so i couldn't tell you.
what bolts are you getting sent :?
Image
m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds :)
Andyboy
Alpina Colada
Posts: 12577
Joined: Mon Sep 11, 2006 11:00 pm
Location: Notts

Post Thu Apr 29, 2010 9:12 am

Bosal = rubbish.

If you want an exhaust that doesn't fit properly, robs power and mpg, and sounds crap, insist on a Bosal. They're shite. I had a grand total of three on mine in the space of three weeks. The noise was dreadful and the quality of the welding abysmal. One was so bad that you could feel the engine struggling - on closer inspection the silencer pipes were misaligned inside by about 10mm. In the end I bit the bullet and got an exhaust from BMW. It weighed about twice what a Bosal thing did and sounded superb. The original lasted 16 years so this should be good for a while. Cheap rubbish exhausts arev a false economy. The Bosal junk you've fitted was half the price of a BMW one, but you'll be fitting at least three of them in the time a BMW exhaust takes to rot off and it'll not be as good.

In no way are Bosal exhausts good. They're renowned for their crapness and the same as all the other cheap rubbish - Walker, Timax, Unipart etc.

There's only one exhaust worth a damn and that's a proper BMW system made by either Boysen or Eberspacher. Expensive, but you get what you pay for.
magpie
Old Skooler
Old Skooler
Posts: 28035
Joined: Sun Jun 29, 2008 11:00 pm
Location: Consett,Durham.

Post Thu Apr 29, 2010 9:50 am

so there you have it,buy quality buy once.
Image
m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds :)
User avatar
BEERBOY123
E30 Zone Squatter
E30 Zone Squatter
Posts: 1537
Joined: Sat Jun 06, 2009 11:00 pm

Post Tue Jun 26, 2012 6:02 pm

I'm getting an OEM one fitted this week by BM and can't wait to pick it up. I have been dreaming about it. What would they fit now, in 2012? Still Boysen or Eberspacher? I forgot to ask.
Two headblenders, couple of bags of MC Hammer, 5 litres of FFF, a 48ft bastard, a box of jumped-up custard and some soggy chimps
darkchild
E30 Zone Addict
E30 Zone Addict
Posts: 2729
Joined: Mon Feb 06, 2006 11:00 pm
Location: Kingston 12

Post Tue Jun 26, 2012 9:32 pm

Andyboy wrote:Bosal = rubbish.
Spot on. Buying anything other than an OE exhaust is a false economy if you plan on keeping the car. My E30's original exhaust lasted 18.5 years.

I think my E36's original system lasted 10-11 years. The sh!tty Timax replacement lasted less than 2. :( Sounded awful too. A BMW exhaust is built so much better.
DavieP
E30 Zone Regular
E30 Zone Regular
Posts: 731
Joined: Wed Aug 01, 2007 11:00 pm
Location: South Devon

Post Tue Jun 26, 2012 9:43 pm

Well, over 2 years on and the bosal has been absolutely fine - no power/mpg loss, great exhaust tone and no hint of poor fit/leaks etc. IOW the complete opposite of the criticism above.
Dave in Torquay

Image
MrWhite
E30 Zone Regular
E30 Zone Regular
Posts: 721
Joined: Fri Mar 14, 2008 11:00 pm
Location: Renfrewshire

Post Wed Jun 27, 2012 9:56 pm

I've had a bosal exhaust on my M42 for nearly 2 years. I bought it from you, Mick if I remember right. No issues with it blowing and it looks good with the black tail pipe tip on it.

The general fit was ok but it didn't have a flattened section where it passes under the rear beam, i fitted it and noticed that it had a couple of mm clearance to the beam. Going round right-handers and roundabouts was annoying because it would rattle off the beam. It didn't annoy me enough to be bothered taking the exhaust off to adjust it. I was fixing the prop last week though, so while the exhaust was off i adjusted it with a lump hammer. It doesn't rub anymore, much better. The other area of poor fit was the mount piece for the hanger at the rear beam. It was too tall to be of any use, no hanging would occur, it just rubbed off the rear beam hanger.

I did notice while it was off how much it has corroded. When I bought it it was almost new, very good condition.

I guess this supports the "bosal are shite" argument but for the minute it does the job just fine. When it finally rots through I will be looking for a better quality replacement. What are the thoughts on custom SS systems compared to OEM?
rust never sleeps
polsta
Married to the E30 Zone
Married to the E30 Zone
Posts: 10322
Joined: Fri Oct 09, 2009 11:00 pm
Location: portsmouth

Post Wed Jun 27, 2012 10:04 pm

The bosal ended up ok didnt get any more probs and the tone got better as it beded in with milage, for the price they are not going to be or fit like a 3 times the price oem,but they are fine for the money
G-Bear
E30 Zone Squatter
E30 Zone Squatter
Posts: 1631
Joined: Wed Mar 12, 2008 11:00 pm
Location: Hertfordshire

Post Wed Jun 27, 2012 11:33 pm

BEERBOY123 wrote:I'm getting an OEM one fitted this week by BM and can't wait to pick it up. I have been dreaming about it. What would they fit now, in 2012? Still Boysen or Eberspacher? I forgot to ask.
A good bit of thread recycling Beerboy... I like it. Caring for the Zone's environment..
User avatar
BEERBOY123
E30 Zone Squatter
E30 Zone Squatter
Posts: 1537
Joined: Sat Jun 06, 2009 11:00 pm

Post Thu Jun 28, 2012 5:15 pm

More that I did a search first to see general opinions on different sorts of exhaust and this one came up from a while ago. So yes, I sort of recycled it!

Out of interest, what is the actual function of the backbox?
Two headblenders, couple of bags of MC Hammer, 5 litres of FFF, a 48ft bastard, a box of jumped-up custard and some soggy chimps