Weepy Head Gasket
Moderator: martauto
-
OllieB
- E30 Zone Regular

- Posts: 676
- Joined: Sat Jun 25, 2005 11:00 pm
- Location: Winchester, Hants
My head gasket is weeping oil near the water pump ever so slightly, I think it was caused by the previous water pump seizing while doing excessive and illegal speeds on the motorway
The car was really slow before the pump went and I reckon it was putting huge load on the belt, and therefore the engine, causing the gasket failure. What I want to know is how quickly is this likely to get worse, or can I pretend all is ok cos H/G is quite a big job. Will driving the car hard quicken its demise? Sorry for long post..... 
-
johnono
- E30 Zone Addict

- Posts: 4677
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: land of the vikings
fella, its all up to u..
peace of mind would suggest " get it sorted before the motor goes tits up"
bank book may suggest " sod that, i aint made of money!"
if u have another car to use then D.I.Y
its a biggish job though.. timing belts , pumps , tensioners, new bolts, gaskets, sealants, and the tools to do it. and all the pipe work, bleeding the coolant, prolly an oil change as uԚ´re there,
not a 5 minute job on a saturday afternoon before the footy
but, thereԚ´s always the garage to sort it
peace of mind would suggest " get it sorted before the motor goes tits up"
bank book may suggest " sod that, i aint made of money!"
if u have another car to use then D.I.Y
its a biggish job though.. timing belts , pumps , tensioners, new bolts, gaskets, sealants, and the tools to do it. and all the pipe work, bleeding the coolant, prolly an oil change as uԚ´re there,
not a 5 minute job on a saturday afternoon before the footy
but, thereԚ´s always the garage to sort it
-
OllieB
- E30 Zone Regular

- Posts: 676
- Joined: Sat Jun 25, 2005 11:00 pm
- Location: Winchester, Hants
My mate is a mechanic, get him to do everything on my car, with my supervision of course
Problem is appropriate bribes, can I do it in my garage at home over time, or should it be on a ramp? I own a transit connect so I don't need to drive my sport. I haven't the patience or temperament to do mechanic stuff myself, managed an oil and filter the other day though!
Problem is appropriate bribes, can I do it in my garage at home over time, or should it be on a ramp? I own a transit connect so I don't need to drive my sport. I haven't the patience or temperament to do mechanic stuff myself, managed an oil and filter the other day though!
-
johnono
- E30 Zone Addict

- Posts: 4677
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: land of the vikings
do it as project the mate
get the mechanic over on the weekend for some brewskis and get the low down
get the mechanic over on the weekend for some brewskis and get the low down
-
OllieB
- E30 Zone Regular

- Posts: 676
- Joined: Sat Jun 25, 2005 11:00 pm
- Location: Winchester, Hants
If I just go into 'ignore' mode, whats the worst case scenario out of interest.....?
-
johnono
- E30 Zone Addict

- Posts: 4677
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: land of the vikings
compression loss = no power
ring seal faliure = burns oil and dies
blending of water from the jacket into the cylinder = mayonaise (over heating coolant, steam and cracked head)
oil loss = dry engine so bearing wears out (dead engine)
all pretty worst case there fella...
on the up side, all the m20Ԛ´s ive heard of leaking oil are on the injector side towards the front arount the oil filter, some others have a soggy gasket too,
if u feel its worth the work then do it, or take a chance ;)
ring seal faliure = burns oil and dies
blending of water from the jacket into the cylinder = mayonaise (over heating coolant, steam and cracked head)
oil loss = dry engine so bearing wears out (dead engine)
all pretty worst case there fella...
on the up side, all the m20Ԛ´s ive heard of leaking oil are on the injector side towards the front arount the oil filter, some others have a soggy gasket too,
if u feel its worth the work then do it, or take a chance ;)
-
elliot
- E30 Zone Regular

- Posts: 622
- Joined: Sun May 01, 2005 11:00 pm
- Location: banbury oxon

-
Fushion_Julz
- E30 Zone Camper

- Posts: 1295
- Joined: Tue Jun 07, 2005 11:00 pm
- Location: Blackwater
Are you sure it is the head gasket itself, not the timing case gasket?
Head gasket problems are usually accompanied by loss of compression and/or water-oil mixing (white emulsion in the cam cover or oily residue in the water) and/or mis-firing
Non of these and I'd say your head gasket is OK and the problem is the timing case gasket
Head gasket problems are usually accompanied by loss of compression and/or water-oil mixing (white emulsion in the cam cover or oily residue in the water) and/or mis-firing
Non of these and I'd say your head gasket is OK and the problem is the timing case gasket
1987 Henna Rot M3 (was 195bhp CAT..now more and no cat)
2001 E46 330i SE Touring (manual)
2001 E46 330i SE Touring (manual)
-
OllieB
- E30 Zone Regular

- Posts: 676
- Joined: Sat Jun 25, 2005 11:00 pm
- Location: Winchester, Hants
very slight misfire, but only when you stab the throttle very quickly when the car has just been started after a long time (eg overnight)

-
OllieB
- E30 Zone Regular

- Posts: 676
- Joined: Sat Jun 25, 2005 11:00 pm
- Location: Winchester, Hants
Forgot to mention, oil is only apparent near the water pump. Car is not losing any oil, eg no drips on garage floor when parked overnight.
-
Simon13
- The longest resto in the world !
- Posts: 22697
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Camberley, Surrey don't u know
if u cane it when it's suspect u will see it off pretty quick i'd say, but i drove my 318is with a dogey head gasket for months...............but not hard
put it this way i wouldn't be doing any clutch kicking
put it this way i wouldn't be doing any clutch kicking
