re-spray
Moderator: martauto
-
jasonbold
- E30 Zone Newbie

- Posts: 235
- Joined: Sat Mar 03, 2007 11:00 pm
- Location: Essex
I've recently aquired a pre-facelift coupe, and its original colour is graphite grey and one of the previous owners had a cheap spray job in bright lime green. it wasn't a full re-spray, just the surface. i want it back to its original colour so do i do the surface again or do it properly and strip it completely?
-
jasonbold
- E30 Zone Newbie

- Posts: 235
- Joined: Sat Mar 03, 2007 11:00 pm
- Location: Essex
Mods could you please move this to Chat please. posted in wrong section.
cheers
cheers
-
initial_g
- E30 Zone Moderator

- Posts: 975
- Joined: Fri Oct 24, 2008 11:00 pm
- Location: derby
it doesnt want stripping (will probibly open a huge can of worms?) nib the imperfections flat the body down so the orange peel and imperfections have gone, use 1500 and wet flat it basicly make it smooth and take the shine off
on the otherhand if its had a cheap respray it maybe full of filler ect so the wheel archers may have been filled and if you have it painted rust could pop through anytime, if you putting money into it have them weld a pair of new wheel archers in it
on the otherhand if its had a cheap respray it maybe full of filler ect so the wheel archers may have been filled and if you have it painted rust could pop through anytime, if you putting money into it have them weld a pair of new wheel archers in it
-
m_jermyn
- E30 Zone Team Member

- Posts: 4208
- Joined: Sat Mar 14, 2009 11:00 pm
- Location: Sydney Australia Mate
You dont need to strip it all down, Start with 240 dry paper and then you will need to high fill it. Once its high filled 240 dry 600 wet 800 wet and 1200 wet. Mask it up clean. it and now you can paint it.
If you do it any other way then this you will more then likely have troubles. You dont know what quality of paint is on the car so you want to start with 240 to remove a fair bit of it. 180 would be better, then after the 180 go to 240. The highfill is there as a primer and also to seal the paint beneath.
If you want some profesional advice take it from a panel beater spray painter, people who dont know what they are doing are going to reply to this thread, but unless they advise you as what I have said take it as a grain of salt.
But as he has said above you dont know what is under the paint in the way of rust or filler. So a full strip down is the only way to be sure
Mike
If you do it any other way then this you will more then likely have troubles. You dont know what quality of paint is on the car so you want to start with 240 to remove a fair bit of it. 180 would be better, then after the 180 go to 240. The highfill is there as a primer and also to seal the paint beneath.
If you want some profesional advice take it from a panel beater spray painter, people who dont know what they are doing are going to reply to this thread, but unless they advise you as what I have said take it as a grain of salt.
But as he has said above you dont know what is under the paint in the way of rust or filler. So a full strip down is the only way to be sure
Mike
-
jasonbold
- E30 Zone Newbie

- Posts: 235
- Joined: Sat Mar 03, 2007 11:00 pm
- Location: Essex
m_jermyn wrote:You dont need to strip it all down, Start with 240 dry paper and then you will need to high fill it. Once its high filled 240 dry 600 wet 800 wet and 1200 wet. Mask it up clean. it and now you can paint it.
If you do it any other way then this you will more then likely have troubles. You dont know what quality of paint is on the car so you want to start with 240 to remove a fair bit of it. 180 would be better, then after the 180 go to 240. The highfill is there as a primer and also to seal the paint beneath.
If you want some profesional advice take it from a panel beater spray painter, people who dont know what they are doing are going to reply to this thread, but unless they advise you as what I have said take it as a grain of salt.
But as he has said above you dont know what is under the paint in the way of rust or filler. So a full strip down is the only way to be sure
Mike
Thanks for your advice mate, i've decided i want a thorough job done on the car. so i will be stripping it right down to its birthday suit. The car is for keeps so i need to know i've got a goodun.
Cheers Fellas
