Good work trevor, is yours an auto btw?
B7's C2.7 Build - FINITO!!!!!!
Moderator: martauto
-
oakey
- E30 Zone Addict

- Posts: 4891
- Joined: Fri Feb 10, 2006 11:00 pm
- Location: Surrey
325i cam is plenty good for loads of torquage
Good work trevor, is yours an auto btw?
Good work trevor, is yours an auto btw?

-
B7
- E30 Zone Team Member

- Posts: 15841
- Joined: Tue Feb 13, 2007 11:00 pm
- Location: Surrey / West Sussex
Yeah switchable Auto.oakey wrote:325i cam is plenty good for loads of torquage![]()
Good work trevor, is yours an auto btw?
B7's Motto. "If it's French, BURN IT!!!!!!"
-
alpinac227
- E30 Zone Newbie

- Posts: 32
- Joined: Mon Oct 31, 2005 11:00 pm
I have the genuine article a C2 2.7i in Alpina Green and the head went - to cut a long (and painful to recall!) I got lucky and located a C2 2.7i Engine overseas and had it shipped over. Only had 62kMiles and is an absolute corker - fell in love with the car all over again. Worth all the effort - so hang in there. I only get on this site every few weeks so may be late in replying in case. But I'll be interested to know how yours goes. All the best mate.
-
B7
- E30 Zone Team Member

- Posts: 15841
- Joined: Tue Feb 13, 2007 11:00 pm
- Location: Surrey / West Sussex
You were the guy Barry and i spoke to at Gaydon I think? You decided not to sell then?alpinac227 wrote:I have the genuine article a C2 2.7i in Alpina Green and the head went - to cut a long (and painful to recall!) I got lucky and located a C2 2.7i Engine overseas and had it shipped over. Only had 62kMiles and is an absolute corker - fell in love with the car all over again. Worth all the effort - so hang in there. I only get on this site every few weeks so may be late in replying in case. But I'll be interested to know how yours goes. All the best mate.
This engine came out of a c2 2.7 4 door in the same colour as yours.
B7's Motto. "If it's French, BURN IT!!!!!!"
-
bss325i
- E30 Zone Team Member

- Posts: 24532
- Joined: Sat Jan 20, 2007 11:00 pm
- Location: London/Surrey
Thats him Trev.B7 wrote:You were the guy Barry and i spoke to at Gaydon I think? You decided not to sell then?alpinac227 wrote:I have the genuine article a C2 2.7i in Alpina Green and the head went - to cut a long (and painful to recall!) I got lucky and located a C2 2.7i Engine overseas and had it shipped over. Only had 62kMiles and is an absolute corker - fell in love with the car all over again. Worth all the effort - so hang in there. I only get on this site every few weeks so may be late in replying in case. But I'll be interested to know how yours goes. All the best mate.
This engine came out of a c2 2.7 4 door in the same colour as yours.
-
old_skool
- E30 Zone Team Member

- Posts: 3405
- Joined: Fri Sep 01, 2006 11:00 pm
- Location: Glossersure
This is looking very good Trev. I have only just spotted this and read all the way through. I'm loving the detail and the cleanliness. The resized pictures don't do these oil pump assembly sections much justice - roll on the new zone, no picture resizing!.
The C2 2.7 is a great re work of the super M20 - those that profess them to be boat anchors just haven't experienced one. The M20 still sounds like the epitome of what a BMW engine should sound like IMO.
-
Jhonno
- Homo Hair
- Posts: 20362
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: FLAT, FLAT, FLAT!!
Soooooooo.. Hows this coming along? 
-
B7
- E30 Zone Team Member

- Posts: 15841
- Joined: Tue Feb 13, 2007 11:00 pm
- Location: Surrey / West Sussex
Not very quickly i'm afraid! Been so busy with work and in the evenings. Hope to start very soon putting her back together. I really need to get my other lump riaght out as I need some bits of that. Could do with both blocks side by side rather than 16 miles apart!!!! Simons willing to come over, it's just my time I need to sort.
B7's Motto. "If it's French, BURN IT!!!!!!"
-
Jesus325iTouring
- Frog freak !

- Posts: 11356
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Omnipresent!
Funnily enough Trev,it's this thread that's inspired me to rebuild the top end of the Corsa Diesel in my drive,I could have sold it for a hundred quid and made a quick buck,but figure,looking at the extent of your total rebuild,a simple top end rebuild for me should be easy peasy by comparison.
Stripping engines is not something I've ever done with cars,except the head gasket on my 5. Most of the cars I've had where there has been engine issues are close to being scrapped anyway so have been little point messing about with.
Stripping engines is not something I've ever done with cars,except the head gasket on my 5. Most of the cars I've had where there has been engine issues are close to being scrapped anyway so have been little point messing about with.

X5 V8 for thrills, CRV for chills, Range Rover P38 V8 for sooooo much aggravation...
-
B7
- E30 Zone Team Member

- Posts: 15841
- Joined: Tue Feb 13, 2007 11:00 pm
- Location: Surrey / West Sussex
Blimey. I'm inspiring
That Corsa shouldn't be anything out of the ordinary. 100 quid these days don't do far and if it's repairable it's run on a thimble of derv and cost you naff all to run. My kinda car. That MX5 I'm using? Owes me 1500 quid ALL IN. Thats the bodywork, full service, a clutch, new hood etc. I've used the car for 6 months at a regular 30mpg, put 6000 miles on it trouble free and had plenty of "tail out" fun
. If I sell that for what it owes me (and it would sell for that all day long) it's better than cheap motoring 
That Corsa shouldn't be anything out of the ordinary. 100 quid these days don't do far and if it's repairable it's run on a thimble of derv and cost you naff all to run. My kinda car. That MX5 I'm using? Owes me 1500 quid ALL IN. Thats the bodywork, full service, a clutch, new hood etc. I've used the car for 6 months at a regular 30mpg, put 6000 miles on it trouble free and had plenty of "tail out" fun
B7's Motto. "If it's French, BURN IT!!!!!!"
-
SteSE
- Heading for the Naughty Room
- Posts: 1477
- Joined: Sun May 21, 2006 11:00 pm
- Location: Gatwick
Hi Trev, hope all is well. I'd like to help in anyway that i can just give me a call. Re fiche, towards the end of next week and they should be electronic and ready for our little mits oooooo 
-
Jesus325iTouring
- Frog freak !

- Posts: 11356
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Omnipresent!
Can't beat cheap motoring,well I guess if you have money you can,but as I haven't............B7 wrote:Blimey. I'm inspiring![]()
That Corsa shouldn't be anything out of the ordinary. 100 quid these days don't do far and if it's repairable it's run on a thimble of derv and cost you naff all to run. My kinda car. That MX5 I'm using? Owes me 1500 quid ALL IN. Thats the bodywork, full service, a clutch, new hood etc. I've used the car for 6 months at a regular 30mpg, put 6000 miles on it trouble free and had plenty of "tail out" fun. If I sell that for what it owes me (and it would sell for that all day long) it's better than cheap motoring
Started my work,what a b4astard to work on,so little room,still, the heads ready to come off just have the cam sprocket to line up and remove.
Anyway,enough about me,this is your engine rebuild thread!

X5 V8 for thrills, CRV for chills, Range Rover P38 V8 for sooooo much aggravation...
-
ricey46
- E30 Zone Regular

- Posts: 982
- Joined: Fri Dec 02, 2005 11:00 pm
- Location: Edinburgh
Well Trev how's this going?? 
Paul.
325i sport Tech1
335i Chromie - Sold
2001 E46 M3-Sold
1999 E39 M5

325i sport Tech1
335i Chromie - Sold
2001 E46 M3-Sold
1999 E39 M5

-
B7
- E30 Zone Team Member

- Posts: 15841
- Joined: Tue Feb 13, 2007 11:00 pm
- Location: Surrey / West Sussex
All been a bit quiet of late so a quick update. I hope to steam ahead next week.
I've been waiting for a guy I know to sort the sheared sump bolt out but I can't wait no longer so today the bare block was taken to southern rebore for them to sort it. it will be back on monday and I can start bolting big oily bits back into it.
The block is now honed and cleaned and is ready for paint, I have a box full of parts, a head built sitting on the bench..........sit tight peeps. It's all go from here.
I've been waiting for a guy I know to sort the sheared sump bolt out but I can't wait no longer so today the bare block was taken to southern rebore for them to sort it. it will be back on monday and I can start bolting big oily bits back into it.
The block is now honed and cleaned and is ready for paint, I have a box full of parts, a head built sitting on the bench..........sit tight peeps. It's all go from here.
B7's Motto. "If it's French, BURN IT!!!!!!"
-
d6dph
- Married to the E30 Zone

- Posts: 12435
- Joined: Sun Aug 14, 2005 11:00 pm
- Location: Tiptree. Essex
Trev, This has just reminded me about that castrol sticker. Can you email it over again for me please. We lost all of the saved emails when changed to this forum style, not sure why but it was a pain. 

-
Jesus325iTouring
- Frog freak !

- Posts: 11356
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Omnipresent!
That feelinf of a snapped bolt,miserable!B7 wrote:
I've been waiting for a guy I know to sort the sheared sump bolt out but I can't wait no longer so today the bare block was taken to southern rebore for them to sort it.
I had two shear off the Transit the other day whilst fitting new wheel bearings,one caliper and one hub->shock bolt,cost 50 quid to have the buggers milled out and re tapped.

X5 V8 for thrills, CRV for chills, Range Rover P38 V8 for sooooo much aggravation...
-
B7
- E30 Zone Team Member

- Posts: 15841
- Joined: Tue Feb 13, 2007 11:00 pm
- Location: Surrey / West Sussex
Dave, Thanks mate, I'll mail it over now. Cheers, will finish it off nicely.d6dph wrote:Trev, This has just reminded me about that castrol sticker. Can you email it over again for me please. We lost all of the saved emails when changed to this forum style, not sure why but it was a pain.
B7's Motto. "If it's French, BURN IT!!!!!!"
-
B7
- E30 Zone Team Member

- Posts: 15841
- Joined: Tue Feb 13, 2007 11:00 pm
- Location: Surrey / West Sussex
Well, the head is as far as it can go now until I actually fit it at which time I'll fit the rocker gear. I don't want to leave pressure on the valve gear when it's not torqued down. Heres a few shotes with all the new studs etc. Now all wrapped up awaiting for the block to return.












B7's Motto. "If it's French, BURN IT!!!!!!"
-
Jhonno
- Homo Hair
- Posts: 20362
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: FLAT, FLAT, FLAT!!
Softcore porn
Looking good Trevor!
Looking good Trevor!
-
bss325i
- E30 Zone Team Member

- Posts: 24532
- Joined: Sat Jan 20, 2007 11:00 pm
- Location: London/Surrey
-
B7
- E30 Zone Team Member

- Posts: 15841
- Joined: Tue Feb 13, 2007 11:00 pm
- Location: Surrey / West Sussex
Today i rushed down to Southern rebore to collect the block. They've had to helicoil the sheared sump bolt thread due to some muppet
trying to drill it out!
Heres the helicoil. A lovely job and all for 13 quid!!! RESULT!

So heres where we are now. Blocks back on the stand (barry I promise you'll have it back soon, cheers mate. All degreased and Honed and just requiring a thinners down before paint. It will be Black (obviously) but i want it to be as close to original as possible. This isn't gloss and it's not true satin. It's a cross between the two. So out with the mixing pot it'll be.





and the all important C2 stamping. You'd think they's have made a better job of it but hey ho. It's the real deal at least.

So from here I have no excuses anymore. Lets get painting and throwing lots of clean bits at it!!!
Ooooh, the front of my trousers are tightening already!
Heres the helicoil. A lovely job and all for 13 quid!!! RESULT!

So heres where we are now. Blocks back on the stand (barry I promise you'll have it back soon, cheers mate. All degreased and Honed and just requiring a thinners down before paint. It will be Black (obviously) but i want it to be as close to original as possible. This isn't gloss and it's not true satin. It's a cross between the two. So out with the mixing pot it'll be.





and the all important C2 stamping. You'd think they's have made a better job of it but hey ho. It's the real deal at least.

So from here I have no excuses anymore. Lets get painting and throwing lots of clean bits at it!!!
Ooooh, the front of my trousers are tightening already!
B7's Motto. "If it's French, BURN IT!!!!!!"
-
spook
- League two here we come !!!
- Posts: 7583
- Joined: Sat Aug 19, 2006 11:00 pm
- Location: portsmouth
Good stuff Trevor, is this your first engine build? 

-
Simon13
- The longest resto in the world !
- Posts: 22697
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Camberley, Surrey don't u know
trevs rebuilt plenty of A series scrap before, the bimmer donk should be a revelation!
-
B7
- E30 Zone Team Member

- Posts: 15841
- Joined: Tue Feb 13, 2007 11:00 pm
- Location: Surrey / West Sussex
The first for a few years. Originally I cut my teeth on A series Minis. Then a couple of crossflows for mates, a fiat mirafiori engine etc. The last full rebuild was in abou '93 and my brother in laws Metro Turbo. F*cking told him not to buy one. The geabox was w4nked and as it was letting go the oil pump picked up the debris and BANG!!! Funny enough, I used Southern Rebore for the machining on that lump as well.spook wrote:Good stuff Trevor, is this your first engine build?
B7's Motto. "If it's French, BURN IT!!!!!!"
-
B7
- E30 Zone Team Member

- Posts: 15841
- Joined: Tue Feb 13, 2007 11:00 pm
- Location: Surrey / West Sussex
Beat me to it!!Simon13 wrote:trevs rebuilt plenty of A series scrap before, the bimmer donk should be a revelation!
B7's Motto. "If it's French, BURN IT!!!!!!"
-
Jesus325iTouring
- Frog freak !

- Posts: 11356
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Omnipresent!
No excuse's now Trev,get in that garage with the baby monitor,a cup of coffee and a dollop of elbow grease,you should be able to nail it all back together by morning 

X5 V8 for thrills, CRV for chills, Range Rover P38 V8 for sooooo much aggravation...
-
E30BeemerLad
- Married to the E30 Zone

- Posts: 16806
- Joined: Mon Mar 28, 2005 11:00 pm
- Location: Norfolk
I noticed a pack of Richmond Superking Menthols lurking in one of those head shots
They have helped me through many an arse scratching whilst working on my turd
They have helped me through many an arse scratching whilst working on my turd
-
Simon13
- The longest resto in the world !
- Posts: 22697
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Camberley, Surrey don't u know
me and trev like a mental fag!

-
Jesus325iTouring
- Frog freak !

- Posts: 11356
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Omnipresent!
And meSimon13 wrote:me and trev like a mental fag!

X5 V8 for thrills, CRV for chills, Range Rover P38 V8 for sooooo much aggravation...
-
Simon13
- The longest resto in the world !
- Posts: 22697
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Camberley, Surrey don't u know
someone edited that post of mine by adding that pink poof smiley!
-
B7
- E30 Zone Team Member

- Posts: 15841
- Joined: Tue Feb 13, 2007 11:00 pm
- Location: Surrey / West Sussex



B7's Motto. "If it's French, BURN IT!!!!!!"
-
bss325i
- E30 Zone Team Member

- Posts: 24532
- Joined: Sat Jan 20, 2007 11:00 pm
- Location: London/Surrey
Stop being such tart!
Shouldn't the core plugs unpainted though?
Shouldn't the core plugs unpainted though?
-
powelly
- E30 Zone Squatter

- Posts: 1649
- Joined: Wed Dec 06, 2006 11:00 pm
- Location: On the scrap heap
Trev, assuming you used VHT type paint, it might dull down a bit after running it up, it's my understanding that heat fully cures the paint. Looks good though.
Le Mans Classic 2006-
B7
- E30 Zone Team Member

- Posts: 15841
- Joined: Tue Feb 13, 2007 11:00 pm
- Location: Surrey / West Sussex
Yes they should. But it' didn't look right!bss325i wrote:Stop being such tart!![]()
Shouldn't the core plugs unpainted though?
It's still dulling down now as it happens so I reckon heat will cure it more.
B7's Motto. "If it's French, BURN IT!!!!!!"
-
ricey46
- E30 Zone Regular

- Posts: 982
- Joined: Fri Dec 02, 2005 11:00 pm
- Location: Edinburgh
Well Trev any updates?? 
I'm still awiting rings shells and loads of other goodies from the stealers, can't wait to get stuck in
I'm still awiting rings shells and loads of other goodies from the stealers, can't wait to get stuck in
Paul.
325i sport Tech1
335i Chromie - Sold
2001 E46 M3-Sold
1999 E39 M5

325i sport Tech1
335i Chromie - Sold
2001 E46 M3-Sold
1999 E39 M5


