Rear Toe/Camber tabs - With price!

[gcs325i]

My address was on my paypal payment. Any news on these?

[caneswell]

I've PM'd the address. Any news?

[Jhonno]

They are made.. They should have/be sending them out

[march109]

AWESOMENESS.

[shorty73]

What's going on with these?

[DanThe]

[Jhonno]

Have people not recieved any yet?

Dan, big apologies for yours as I have them! I just haven't had a car and been rather busy..

I will try and see if they are there tomorrow morning and ask what is happening If not I will call them 1st thing Monday morning

[gcs325i]

No. Nothing yet.

[Jhonno]

Ok, I will have a word

[DRIFTBOY]

Nowt here either dude, cheers for getting on the case!

[pilt]

Hi,

I would really like these by the end of the week as i have my subframe stripped and ready to weld and really need to put it back on next weekend! So can u give em the hurry up!

Cheers

Dan

[mccarthy]

any spare kit's?

[Jhonno]

Right spoke to them today, they are sending them out tomorrow or Wed, sorry for the delay again, ive been rather occupied!

there are spare kits yes..

[mccarthy]

where abouts in essex are they/what m25 junction? be great to get them welded at same time as others have done! how much extra cost did this put on top?

[winx]

any idea when the supplied beams are going to be welded? Got some time this weekend so could collect

[Jhonno]

I will sort the welding out as I want mine done asap also..

mccarthy, I am in Colchester, Jct 28 of the M25..

[JungleGus]

i know it's way late - is there any chance of still getting in on it or plans for a 2nd batch?

Thanks!

[pilt]

Hey,

Just wondering if you know if they have been sent out yet?

Sorry for being impatient, just it will save me from having to remove my subframe twice if i get them before the weekend!

Cheers

Dan

[BadDave]

My tabs arrived this morning courtesy of the postie.

Thanks Dan.

[Dave_M3]

any body have any pics of these?
I'm dying to see what this compromise looks like

[shorty73]

No reply to email or P.M's? Jhonno have you got my delivery address? Getting a bit concerned over lack of communication.

[winx]

I wouldnt worry too much fella, dan has taken a while to reply to my emails/pms before and was just too busy to remember them! Came good in the end.

[hoshy]

Dan - can you ask these guys to post mine out please. I've PMd the address.

Ta.

[DRIFTBOY]

Anyone apart from BadDave got these yet?

[BadDave]

Anyone apart from BadDave got these yet?

It looks like it may be an issue with the company that's been used to manufacture the tabs.

Dan(Jhonno) picked up mine and sent them up to me,as I was happy with that delivery method.

It might be a good idea to let folks who paid direct,know who's manufacturing the tabs and there contact details(contacts name,address and phone number).
It would give them the opportunity to contact the Fab shop involved directly regarding the delivery issues.

[Jhonno]

DanThe has got his also..

Having spoken to them, it sounds like they have messed it up again. I gave them a drawing to make them, the previous problem was 'rectified', where I took the drawing up again and left of one the correctly orientated ones on their desk, only for them it would appear to rerun the wrong ones

They apparently are having to re run them again! Which has confused the hell out of me, as when I went up to get Dave's and DanThe's, they pulled a bag out and it had correctly orientated tabs in which were supposedly the rerun batch

I can only apologise and say lessons learnt with dealing with Group Buys.. I will take money next time and pay and post out myself etc

I would honestly feel bad about giving the company name out, as I don't feel what has gone on is an accurate representation of them.. Frustrating as it has been

[DanThe]

Dan, I pm'd you about the problem with those you sent me, I take it they were from a 'faulty batch'? Are they making some to the drawing now?

[BadDave]

As there's an issue with the one's sent to Danthe,I've just double checked the one's that were sent to me.

The ones sent to me.


And the ones in the post/I.E site.



The ones i've got appear to be the correct ones.

[DRIFTBOY]

All sorted!

[BadDave]

They look rather simple, how the feck did an engineering company get those wrong?

Just a guess, but i reckon they folded the wrong 2 edges meaning the slotted holes ran parallel to the raised edges.

[DRIFTBOY]

All sorted!

[DanThe]

Well, if you try a bolt into them Dave you will realise they have been made wrong! The edges should not be folded, the piece should be made from 8mm flat bar, they should be milled, the folded edge creates a radius which stops the bolt dropping all the way in, ive exchanged a few pm's with Jhonno about it and it seems he has filed down the edges of the bolts/washers so they fit flush, I dont like the idea of this as apart from the amount of money the firm has had out of this group buy the folded edge is much thinner and with a weld on the back of it its likely to distort, if they are making them again im up for returning these

[BadDave]

A milled 90deg edge would indeed be better than the current folded edge.

Jhonno did mention that there would be a little tweak required to make it work as it should.

A proper milled set of tabs would be the preferred option, however, as they've mucked up 2 batches already, there's probably little chance of them doing a milled batch.

[Jhonno]

A milled 90deg edge would indeed be better than the current folded edge.

Jhonno did mention that there would be a little tweak required to make it work as it should.

A proper milled set of tabs would be the preferred option, however, as they've mucked up 2 batches already, there's probably little chance of them doing a milled batch.

This is the trouble! I shall speak to them and see if they have started the new batch, if not then I will ask them to mill them.

I have no idea why they folded them tbh!

The 'wrong' ones they did with the slot parallel to the lip as has been said! I get the feeling I am not their favourite person, as they seem to be blaming me for the error, when I have only ever given them 1 drawing and a even the above picture of what they should look like

[DanThe]

Sorry if you boys think im being fussy, but if they are being arsey ive no problem having my money back, and TBH id rather that than these folded tabs