GF boot lid + bonnet (ended)

[SteMarsden]

I'd be interested in putting my name down if we could get a few more names

[kipsy]

So anyone else interested? Maybe reopen thread to see if interest?

[ABSMotorsport]

OK, put your names down below, same prices as before..

[kipsy]

Just before I put name down I'd be interested if someone could put a picture up of the fitted bonnet and bootlid and how are people going about washer jets? Mine would be fitted to a rally car so quite important ;)

[ABSMotorsport]

theres a couple of customer images of the boots fitted on here - http://www.facebook.com/absmotorsport?sk=wall&filter=1
and there are a couple of images of bonnets fitted here -
http://www.absmotorsport.net/bmw/e30.html?p=4

washers - run a pipe direct on the wiper arm.

[kipsy]

They do look good when fitted. Little concerned about how safe the bonnet pod would be? I would need to have dzuz fasteners to fold it down. If the bonnet is strong enough don't really see an issue though. Do we still need the ten people for the new offer? Sorry for all the questions

[ABSMotorsport]

hi, yes it should be ok

yes we would need the 10 again.

[rix313]

I've amended the title to let people know a new GB is pending and to see Page 6 and contact you (ABS) with any questions

[tommyg]

hi can i get a price on these fiberglass parts?

tom 07890260644

[tommyg]

Is it too late to get involved in this?

Do you know where I can get f g panels?

[Jimbob]

A new group buy is starting up mate so now is the time to get involved!

[rix313]

hi can i get a price on these fiberglass parts?

tom 07890260644

I have put the prices in the very first post of the thread (go to the top of page 1).


------------


A new list would be handy if people start getting their names down. Copy and paste the list and add your name:

Bonnet
1.
2.
3.
4.
5.


Boot:
1.
2.
3.
4.
5.

[pdd144c]

Look good, can you make any of the panels with internals?

[ABSMotorsport]

at the moment we dont have moulds for the inners, but we would look at doing them if there was enough interest

[pdd144c]

Well I'd have a set with internals for sure, not like the weight would increase much and so much easier to mount using original fixing holes.

[kipsy]

I would prefer internals to be honest. Depending on price. Still unsure if to get one now or in few months when better off financially as just put entry in for welsh rally Tarmac championship in car and that's going to eat up lots of my funds.

[nickso]

I'll get the ball rolling.

Bonnet
1. Nickso
2.
3.
4.
5.


Boot:
1.
2.
3.
4.
5.

[Motorhole]

Potentially interested with internals for original fixings too.

[Motorhole]

Bonnet
1. Nickso
2. Motorhole (with internals/fixings)
3.
4.
5.


Boot:
1.
2.
3.
4.
5.

[mattxr2]

Bonnet
1. Nickso
2. Motorhole (with internals/fixings)
3.mattxr2
4.
5.


Boot:
1.mattxr2
2.
3.
4.
5.

[ross_jsy]

Bonnet
1. Nickso
2. Motorhole (with internals/fixings)
3.mattxr2
4.
5.


Boot:
1.mattxr2
2. ross_jsy
3.
4.
5.

Down for a boot lid for now. Might be down for a bonnet in the near future. How much do the boots weigh btw?

[samuraibaz]

hi mate am interested in boot but was wondering if they are pinned down front & rear or use any original fixings? cheers baz

[ABSMotorsport]

Hi Baz, they are pinned front and rear, but i dount this 2nd group buy will get the numbers...

[jonnyfartpants]

put me on the list for a boot and bonnet
cheers

[Jimbob]

How much does the replacement bonnet weigh? There's no mention of it in the thread so far.

[mccarthy]

Bonnet
1. Nickso
2. Motorhole (with internals/fixings)
3.mattxr2
4.
5.


Boot:
1.mattxr2
2. ross_jsy
3. mccarthy
4.
5.

Also interested in a FG roof. Have spoke to you a while back i think Tony but due to work circumstances i couldn't commit. Am able to purchase now though but i can discuss this over the phone with you.

[Jimbob]

Bonnet
1. Nickso
2. Motorhole (with internals/fixings)
3.mattxr2
4. Jimbob
5.


Boot:
1.mattxr2
2. ross_jsy
3. mccarthy
4.
5.

[Motorhole]

Bonnet
1. Nickso
2. mattxr2
3. Jimbob
4.
5.


Boot:
1.mattxr2
2. ross_jsy
3. mccarthy
4.
5.

Sorry folks, need to take my name off this, sourced another bonnet

[Martin347]

Would it be possible to get a price on just the internals for the bonnet and boot? I bought a bonnet and boot on a group buy a while ago and have never fitted them because I didn't really want them just on pins. If I could get the internals, I could bond them on myself and job done!

Thanks, Martin.