Removing Crank Pulley

Need technical Q/A then you're in the right place

Moderator: martauto

Kedge
Old Skooler
Old Skooler
Posts: 7698
Joined: Thu Jan 13, 2005 11:00 pm
Location: Leicestershire

Post Sat Feb 10, 2007 1:25 pm

Chaps,

I need to remove the crank pulley from my M42, however the engine is sat on an engine stand so i can't lock it up by putting it in gear!

Whats tricks have you guys got for doing this?

Cheers
Image
'86 Polaris 316 M20B28 Rebuild
Instagram - Kedge85
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Sat Feb 10, 2007 1:37 pm

Ive found the best solution with engine on a stand is to heat the bolt (until the oil seal melts hot) then an impact gun will bring it out easy.
This was with M50/52 engines but I dont think the torque setting is too different
Kedge
Old Skooler
Old Skooler
Posts: 7698
Joined: Thu Jan 13, 2005 11:00 pm
Location: Leicestershire

Post Sat Feb 10, 2007 3:58 pm

Sounds like a plan, although i haven't got an impact gun so a big bar may have to do!
Image
'86 Polaris 316 M20B28 Rebuild
Instagram - Kedge85
Turbo-Brown
Boost Junkie
Posts: 4705
Joined: Tue Feb 15, 2005 11:00 pm
Location: Aldershot, Hants

Post Sat Feb 10, 2007 7:03 pm

I put a 10mm dia stick of ali in between the middle two cylinder's counterweights and the inside of the block to stop the crank turning on my M20.

A big bar and the mass of my fat dad was then used to get the bolt out :)
325i Twin Turbo (until 10am 01/12/07 :( )

www.air-in.co.uk free M20 exhaust and inlet flange
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sat Feb 10, 2007 10:25 pm

Hammer handle jammed between a crank web and the block is the usual way if the sump is off.
E30Mark
E30 Zone Team Member
E30 Zone Team Member
Posts: 8107
Joined: Sun Jan 09, 2005 11:00 pm
Location: Wimborne, Dorset

Post Sat Feb 10, 2007 11:06 pm

I had to give up trying to undo the crank nut on a M42 when it was on the engine stand. Had the sump off and jammed the crank, but no matter what abuse i gave it the thing would not move. I was trying to be good and change the timing chain gasket whilst the engine was out, but ended up putting the engine in the car without changing the gasket. Thankfully the old gasket was fine and never leaked.
1 & 2 bed flats in Bournemouth areas, with parking
PM for details
Kedge
Old Skooler
Old Skooler
Posts: 7698
Joined: Thu Jan 13, 2005 11:00 pm
Location: Leicestershire

Post Mon Feb 12, 2007 3:50 pm

Got it off in the end, jammed the crank with 3/4" drive extension which i put in an old water pipe. Then after heating it up with a blow torch for a few mins she was ready to go with a fair bit of weight! Not too difficult in the end :D
Image
'86 Polaris 316 M20B28 Rebuild
Instagram - Kedge85