Camber and Toe (plates)

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Thu Dec 01, 2011 2:06 pm

Anyone know how much camber correction you can get by using camber plates (and how much +/- toe?) on the rear beam? I have them welded on as close to being centred as I could get them.

I'd like to run the touring with as little camber as is recommended.
Jhonno
Homo Hair
Posts: 20362
Joined: Mon Jan 10, 2005 11:00 pm
Location: FLAT, FLAT, FLAT!!

Post Thu Dec 01, 2011 2:47 pm

Depends where you have welded them..

There is decent adjustment, mine was all in spec, and it was looooooow.
Got cable ties? Get diffin..

Arch roller for hire.

www.zeroexhausts.co.uk

Image
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Thu Dec 01, 2011 3:02 pm

Camber plates on the inside mounts and with the plates centred over the existing hole.

What size wheel were you running? I have some fitment issues with camber dialed out
Image
Image

16x9 et15 225/40
Jhonno
Homo Hair
Posts: 20362
Joined: Mon Jan 10, 2005 11:00 pm
Location: FLAT, FLAT, FLAT!!

Post Thu Dec 01, 2011 3:09 pm

Checked the toe?

Image

215 tyre 8" et20
Got cable ties? Get diffin..

Arch roller for hire.

www.zeroexhausts.co.uk

Image
Jhonno
Homo Hair
Posts: 20362
Joined: Mon Jan 10, 2005 11:00 pm
Location: FLAT, FLAT, FLAT!!

Post Thu Dec 01, 2011 3:10 pm

Check my sig for how far it would tuck WITHOUT any scrub!
Got cable ties? Get diffin..

Arch roller for hire.

www.zeroexhausts.co.uk

Image
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Thu Dec 01, 2011 3:16 pm

It started snowing in my thread :D

Toe seems to make little difference, I'm not sure where it should be either.

I have problems hitting that hump with the tire thats up in the arch if I dial in some camber. I also have the added problem of iX arches in which the wheels will look lost with lots of camber.
Jhonno
Homo Hair
Posts: 20362
Joined: Mon Jan 10, 2005 11:00 pm
Location: FLAT, FLAT, FLAT!!

Post Thu Dec 01, 2011 3:20 pm

Haha. Suddenly got cold in here..

I think mine was running on the upper levels of camber obviously!

Knock the hump flat.. Be careful not to knock it into the outer skin though! Or cut it and weld a flat?
Got cable ties? Get diffin..

Arch roller for hire.

www.zeroexhausts.co.uk

Image
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Thu Dec 01, 2011 3:26 pm

Jhonno wrote: Knock the hump flat.. Be careful not to knock it into the outer skin though! Or cut it and weld a flat?
Cutting and welding has crossed my mind! Should have done it when I fitted a new outer wheelhousing.

Seems I can flare the arches like normal and just trim away at the back of the ix arch flares :banana: