Any ideas tips on how I can polish up my inlet/intake manifold or even how much it would cost to buy?
Thanks
Polished inlet/intake
Moderator: martauto
Anyone? cant see anything in the wiki....
-
Rtaylor2208
- E30 Zone Addict
- Posts: 3004
- Joined: Mon Oct 11, 2010 11:00 pm
- Location: Ayr, Ayrshire, Scotland
StanleyTurbo I think is the user thats had his done.
-
Cloggy Saint
- Old Skooler
- Posts: 8024
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: zummerzet
I've done my inlet, TB and AFM. I started with a wire brush on a dremel and then rubbed it down with increasingly fine wet & dry, from 12 to 2000 and then finished with a fine wire wool. It's not a mirror finish but it looks very nice.
E30 zone - promoting adult illiteracy since 2004
Great! I will give that a try! Any ideas if polishing compound would give it a mirror like finish?
-
BEERBOY123
- E30 Zone Squatter
- Posts: 1537
- Joined: Sat Jun 06, 2009 11:00 pm
It's not a mirror finish! It bloody is! Lovely work.Cloggy Saint wrote:I've done my inlet, TB and AFM. I started with a wire brush on a dremel and then rubbed it down with increasingly fine wet & dry, from 12 to 2000 and then finished with a fine wire wool. It's not a mirror finish but it looks very nice.
Two headblenders, couple of bags of MC Hammer, 5 litres of FFF, a 48ft bastard, a box of jumped-up custard and some soggy chimps
-
BEERBOY123
- E30 Zone Squatter
- Posts: 1537
- Joined: Sat Jun 06, 2009 11:00 pm
BEERBOY123 wrote:"It's not a mirror finish" - It bloody is! Lovely work.Cloggy Saint wrote:I've done my inlet, TB and AFM. I started with a wire brush on a dremel and then rubbed it down with increasingly fine wet & dry, from 12 to 2000 and then finished with a fine wire wool. It's not a mirror finish but it looks very nice.
Two headblenders, couple of bags of MC Hammer, 5 litres of FFF, a 48ft bastard, a box of jumped-up custard and some soggy chimps
I've sent my inlet off to be chrome plated at ashford chroming in Kent, hope they do a good job! I'm polishing the TB AFM and thermostat housing myself, dremmel, fine sandpaper and a lot of autosol does the job! takes a lot of time but well worth it when it's done
-
aimlessrock
- E30 Zone Squatter
- Posts: 1821
- Joined: Sun Dec 06, 2009 11:00 pm
- Location: Manchester
Smithy, would not mine seeing the results of your inlet when your done as am considering having mine done...how much were you quoted if its not a rude question?
E30 320i Convertible (1989)
190 Mercedes (1988)
"there is nothing more expensive than a cheap E30"
190 Mercedes (1988)
"there is nothing more expensive than a cheap E30"
Are you able to do a step by step picture guide? It'll be great for the wiki! I'm trying to get hold of a dremmel...can I use an angle grinder with a wire brush attachment?Smithy89 wrote:I've sent my inlet off to be chrome plated at ashford chroming in Kent, hope they do a good job! I'm polishing the TB AFM and thermostat housing myself, dremmel, fine sandpaper and a lot of autosol does the job! takes a lot of time but well worth it when it's done
Here you go... I ordered one this week comes in a sexy little man bag too 
http://www.amazon.co.uk/gp/aw/d/B0033UW ... ecouk06-21
http://www.amazon.co.uk/gp/aw/d/B0033UW ... ecouk06-21