E30 Zone

how do ii check if the sensor is gone then must confess ive not looked at it myself yet

anyone any other thoughts on what i can check i know its getting fuel plugs were soaked

hia guys hope u can help point me in right direction car been not started for about a month was left outside at local garage waiting for an mot there is basically no spark 1 battrey is ok turns over fine 2 power at coil 3 removed dizzy cap cleaned a sprayed with wd 40 some evidence or a little arkin...

was the 27 pounds for the chrome or the black one

can i buy the crome strips or does it need new the whole lot replacing and if so how do i fit them any one ?

im happy if its ok

got a 325 manual with lsd track day car

was gonna tow it to track days on a dolly will this be ok for the box etc

u can tke a feed off of anything live such as a cig lighter hope thats ok

take off the filler plug at back of the diff the level should be to that hole

ie to much oil it will run out of the hole (i usually just out my finger in to seee if its far off)

what size spanner

got a socket to fit 9/32 wich is obviously no good

shap says that size dont wxist in spanner lol

helo

thanks ed much appreciated

no one ever answer my post sorry its not about a big bore exhaust of 17 inch alpinas

master or slave id start with the cheapest first lol

probably ur idle need adjusting now u have a nice claen carbon free head

just a thought

as i replaced the fron to rear pipe and am replacong with dot five i guess i need to bleed the lot lol. so which order ?

although i did replace the fron too rear pipe that was fun in steel lol

cant seem to get it to clip in to the last clip ( the one neareest the filter under the bonnet) is that a mot failure it goes into all the others ok worried about snapping it the 3m steel pipe that is .

just replaced al my rear brake pipes etc which order should i blled them now is it furthest away from the cylinder ? ie o/s/r ? thanks guys

three line kit just replaces the felxies doesnt it it the long one im needing

wont replaceing a steel pipe with a braided one lose efficency no matter how well reinforced it is

thanks every one

found the goodridge sight but they dont seem to do the fron to back line lol just my luck and one any ideas ( i gonna have to buy a kit to make my own)

had anight mare today bending that steel brake pipe. well three pipes to be honest, brake one the other doesnt fit got one on, went to bmw because i though they would fit straight on stupid me who does a braided hose kit and where do i get one (are the fuel lines bend urself too!

so u took a braided hose straight off the bottom of the brake proportioning valve thing to where right to the wheels ? where did it end etc and this was a kit or something u made urself ive bought the line now and had the petrol tank out allready (having fun here) whats the best way to bend the stee...

thats it thoght it must have been some pressure regulating device i beeter taking it off or leaving it where it is its a bitch to get at espec with 3 meters of brake pipe to fit to it

somebody

just removed the front to rear brake pipe (mot fail) hard enough to remove it , access mainly at the front end where it screws in to a sort of lump (excuse my ignorance before it comes back to the master cylinder. to refit any tips as the new pipe as its so long how best to line it up with the lumpt...

unbolted the fromt, unbolted the back, unbolted the cemtre, neither end of the prop will clear diff or gearbox and that spline dont wanna slide

anyone

how u mean what does this nut do all nuts fron and back centre offf wont cllear gear box or diff

following adam instructions to get me tank out thanks mate, having trouble removing the diff all the fixings are undone the spline seems a to not want to move so i can draw the shaft out plus can the bolts on the diff end be taken out or are the fixed (thought they might be an interfearance fit ?) h...

u guys are always alot of help amogst other things car failed mot on ns outer headlight beam to high when i investigated it swung like a cat flap lol from the top is it likrey to be just a screw or something more serious just tought id ask before i start to delve

now im confused lol the handbrake does opperate the callipers yes, sounds like a small drum set of drum brakes help, (take of the disk is that just that one fixing on the disk face sorry to be such a numpty

cant see ill turn up me torch a bit it as an 85 car but disks all round

do u know the part no. i have this too lol

am i adjusting a screw as i cant see one at all at 12 oclock help, can see bit of a spring in a few places as i rotate wheel

many thanks adam ur a legend as always im just back from four days away sounds like fun all i have to do now is find a tank top fit to the car

so do u have that stuff about a fuel tank change?

yes i would be interested in the tank how much u want? in going to purfleet sinday night too thanks ring me 07977584397

adam did i hear u would give somebody the run down on how to change the fuel tank need some help if u can, now dont laugh is it possible to weld the tank ( i do realise its more dangerous empty than full and how explosive it is) just wondered if there was a trick such as fuilling with sand which see...

Search found 40 matches

Re: mine wont start either

mine wont start either

Re: faded crome inserts on windsreen rubbers

faded crome inserts on windsreen rubbers

towing my 325

brake bleed

which order to bleed the brakes

brake pipe fron to rear

prop shaft

head light like a cat flap

bit confused

adam

tank

fuel tank