E30 Zone

Hi guys, I've replaced my camshaft for a 302° CatCams and i think my clearance is not enought between pistons and valves. Engine rotating well by hand but when i look thouhgt the spark hole with a boroscope, it's look around 1mm to the closest point. What should be the minimum clearance for that kin...

what you mean regarding prices with the forum -- Yes Get the the one with plenum not open stacks -- but behind the plenum there open stacks right ? "All kits are supplied with polished silver trumpets and polished carbon fiber Plenum/ Air-box. See our other listing if airbox is not required." It's l...

OK !
so im gonna search for an RHD !
Do you have any prices wit the forum ?

Back few years later, but engine's running well !! last week on dyno and i'm really happy for the results !! But for the last step im starting to look Dbilas or RHD ITB, i dont know wich one are the best ... So my conf is 2.8 engine 130 rods 11.4vr 299 cat cams aac Dta s80 228.4 hp @6125 289.6Nm @ 5...

Hi guys, Yesterday I try to set my tracking but I cannot set correctly my front camber, I used M3 e36 3.2 settings on the device and I'm not sure about this. For my 5 lugs conversion I used Z3M front struts, E30 HR springs, M3 3.2 spindles, M3 3.2 trailing arms and IRP adjustable front control arms ...

Yep but i want to keep my DTA, for me it's a better ECU than MS
I finally start the loom, it's not easy but it's on the way, I do it with plugs, pins and wires, a 100% homemade loom.

Hi everyone, Is anyone of you already installed an S60 on m20b25 engine with motro 1.3 ? I try by many ways to do the loom but i'm a poor electrical and it's start to be a nightmare . Every time I try to start I spend all the time to think and look all the wiring diagram but in fact I've done nothin...

No, with oil

Ok today i take my time for know exactly what I have ! I have done my crankshaft measurments and I found 44.98 & 59.98, so this is standard size right ? For my rods bearing attrition, it's probaly some bullshit i've done :( During the rods balancing i mix rods and rods end and now without bearings I...

Impressive !

Today I disassembled the engine, to know what's going on inside ! The good thing is now I know why the engine was blocked, the bad is now I have more questions ! I found some rods bearings without the grey coating, with a shinny area, they was new so, I don't understand why just by hand turning the ...

Hi all ! After some lot of work on the chassis for eliminate corrosion, i'm back with my b28 ! and with another problem too ! When i tight the rods on crankshaft the engine is impossible to turn and i have no axial clearance on some rods I think the rods bearing (oemM20b25, 45mm) installed are not i...

Asymmetrical camshaft is more for turbo right ? in my case dbillas 284 or catcams 285 may the better choice for my use.
Never ear about enem z45 but thanks for all your answers

Principaly street but sometimes on tracks
What do you think about a 284 dbillas ?

Now i need to find the correct camshaft.

Thanks reggid

I don't know why i was thinking the Max lift is in TDC, Thanks for the explaination and forget my question

For the moment i don't know wich cams i'm gonna use, all need to be clear in clearance and measurements before ordering camshaft. For the measurement i've done, it's from the top of the head, by the tail of the valve and the top of the guide. First when valve closed and after valve open in contact w...

nice job !! the head gasket is an OEM 1.75mm ?

Hi guys, my M20B28 build is in progress and I've my first problem, sorry for my english, i got to try to be understood My Stuff: m20b25 block, m52b28 crankshaft, 9.7 pistons with skirt ablation, OEM 1.75mm head gasket. The problem is when i measure the valves openning when piston on TDC is not enoug...

OK, thank Reggid, you're right maybe strong loctite is enought !!

Hi, the crank spacer for an m20b28 is free to rotate or blocked by the shaft key ? (without tight the crankshaft bolt)
Mine is free and I try to find a way to fit it but maybe is not required
What do you think ?
Thank you

Search found 22 matches

Re: M20B28 Stroker

Re: M20B28 Stroker

Re: M20B28 Stroker

Re: M20B28 Stroker

Re: M20B28 Stroker

Tracking questions on 5 lugs

Re: DTA S60 Loom

DTA S60 Loom

Re: M20B28 Stroker

Re: M20B28 Stroker

Re:

Re: M20B28 Stroker

Re: M20B28 Stroker

Re: M20B28 Stroker

Re: M20B28 Stroker

Re: M20B28 Stroker

Re: M20B28 Stroker

Re: M20B28 Stroker

Re: M20B28 build 2

M20B28 Stroker

Re: m20b28 crank spacer

m20b28 crank spacer